DBX 1074 NOISE GATE USED (Made in USA)

• Four independent channels of gating
• Independent key filtering
• Independent Threshold and Release controls
• Differentially balanced gold-plated XLR and 1/4" inputs and outputs
• True RMS level detection
• Stereo Coupling mode
• Switchable +4dBu or -10dBv operation per channel

  Input Connectors	XLR (Pin 2 and tip hot)
  Input Type	Electronically balanced/unbalanced, RF filtered
  Input Impedance	Balanced > 50 kOhm, unbalanced >25 kOhm
  Max Input	> +22 dBu balanced or unbalanced
  CMRR	40dB: Typically >55 dB at 1 kHz
  Key Input	Electronically balanced/unbalanced, RF fitered Balanced 50kOhm, unbalanced > 25 kOhm
  Output Connectors	XLR (Pin 2 hot)
  Output Type	Servo-balanced/unbalanced, RF filtered
  Output Impedance	Balanced 60 Ohm, unbalanced 30 Ohm
  Max Output	> +22 dBm balanced, > +20 dBm unbalanced
  Bandwidth	20 Hz to 20 kHz, +0/-0.5 dB
  Frequency Response	0.35 Hz to 200 kHz, +0/-3 dB
  Noise
  Dynamic Range	> 115 dB, unweighted
  THD+Noise	0.008% typical at +4 dBu (1 kHz unity gain), 0.08% typical at +20 dBu (1 kHz unity gain),
  Interchannel Crosstalk
  Stereo Coupling	True RMS Power Summing
  Operating Voltage	100-120 VAC 50-60 Hz or 200-240 VAC 50/60 Hz
  Power Consumption	30 Watts
  Fuse	100-120 VAC:250 mA Slow Blow, 200-240 VAC:125 mA Type T
  Power Connector	IEC receptacle
  Unit Weight	6.9 lbs.
  Shipping Weight	9.3 lbs.

   

The AD2055 combines 100% discrete, pure class A signal amplifiers with state-of-
the-art passive and active filter topologies. The AD2055's unique circuitry delivers
very high resolution transient detail at the operational extremes of real world equalization
demands. The AD2055 auto-bias DC servo loop control eliminates the need for all
interstage capacitor coupling. The AD2055 breathes life into all musical performances!
 
AD2055 FEATURES
Pure Class A, 100% discrete design
Smooth musical detail and sonic excellence
Minimum audio signal path
Dual mono operation
Transparent active and passive filter design
High headroom +30dB Very low noise -94dB
Fully balanced inputs and outputs
DC coupled, no transformers in audio path
Switched frequencies in high and low bands
Mid bands use X10 frequency for extended range
Wide bandwidth -3dB 1Hz to 450kHz
Low distortion less than 0.5% THD and IMD
All signal routing with sealed silver relays Conductive
plastic potentiometers for low noise
External 150W toroidal power supply 100% discrete
power supplies for audio path
Long lasting, stainless steel hardware
 
SONIC EXCELLENCE
The Avalon AD2055 Pure Class A music equalizer is the most powerful, low noise
parametric equalizer available today. Designed to optimize absolute signal integrity
and musical performance, the AD2055 combines the best of active and passive filter
topologies with sonic excellence unequaled by lesser designs. The AD2055 is the
perfect solution for two buss music-program equalization, special instrument EQ and
FX applications and ultra high performance mastering studio's.

Features include state-of-the-art, balanced 100% discrete, Pure Class A signal amplifiers,
practical user features and rugged hardware designed to deliver true high performance
audio for many years. 

PASSIVE-ACTIVE FILTER DESIGN
Avalon equalizers feature the unique combination of both active and passive filter EQ designs.
This special combination enables the AD2055 to deliver high speed transient detail at the
operational extremes of real-world equalization demands. The passive high and low bands offer
alternate musical tone range to the full function active parametric mid bands. Passive equalizers
have long been a favorite with music lovers around the world.  Full bodied, powerful (up to +/-32dB,
64dB range !) and sweet frequency selections are the benefits of the passive high-low EQ bands.
The full bandwidth twin mid bands provide variable frequency selection (X10 frequency multipliers
for very wide range), variable Q (width) and amplitude control.

MINIMUM SIGNAL PATH DESIGN
Avalon's advanced true symmetry design offers high-voltage, large headroom, extended bandwidth
and very low noise. The use of 100% discrete, Pure Class A signal amplifiers give the serious music
professional unlimited sonic character and a natural harmonic detail that enhances the program
material and becomes one with the music itself. The Avalon AD2055 breathes life!

AD2055 SPECIFICATIONS
Circuit Topology  High-voltage 100% discrete, balanced and symmetrical
Class A 
Output Gain Range  Unity Gain 
Maximum Input Level  +30dB balanced XLR pin 2 hot 
Maximum Output Level  +32dB balanced 600 ohms, DC coupled, high-current
discrete Class A 
Input / Output Type  XLR type, pin 2 hot balanced 
Noise 20kHz Unweighted  -94dB (EQ in) 
Distortion THD, IMD  0.5% (typical 0.05% at +6dB 1kHz) 
Frequency Response -3dB  1Hz to 450kHz (input band limited) 
Equalizer Type  Passive high and low bands plus two fully parametric mid
bands 
Bypass  Hard-wire relay bypass for equalizer in-out 
Low Band F1  Passive, amplitude to -32dB to +32dB shelf or peak-dip curve 
F1 Frequency Range  Switched 10 position 18Hz, 25, 30, 50, 72, 100, 150, 215,
300, 450Hz 
Mid Band F2  Active, amplitude to -16dB to +16dB peak-dip curve 
F2 Frequency Range  Variable 35Hz to 450Hz (x10) 350Hz to 4k5Hz, Q (width)
0.3 to 3.0 
Mid Band F3  Active, amplitude to -16dB to +16dB peak-dip curve 
F3 Frequency Range  Variable 160Hz to 2k0Hz (x10) 1k6Hz to 20kHz, Q (width)
0.3 to 3.0 
High Band F4  Passive, amplitude to -26dB to +26dB shelf or peak-dip curve 
F4 Frequency Range  Switched 10 position 1k5Hz, 2k5, 3k5, 5k, 7k2, 10k, 12k5,
15k, 20k, 25kHz 
AC-DC Power  External AC supply, 150w toroidal transformer, 4 pin cable 90v
isolated, 
(B2T Power Supply Included)  100-240v selectable 50/60Hz, 150w max 
Dimensions  19 x 3.5 x 12 in (482 x 88 x 305mm) 
Shipping weight  30lbs (13.6 kg) 

VIRTUALIZER 3D FX2000
High-Performance 3D Multi-Engine Effects Processor
71 breathtaking new algorithms—true RSM (Real Sound Modeling) stereo and 3D effects
Wave-adaptive virtual Room reverb algorithms for natural reverb and delay
Awesome modulation, dynamic, psychoacoustic and EQ algorithms
Authentic amp simulation, distortion and special effects
11 effect combinations with selectable serial / parallel configuration
Up to 7 adjustable parameters plus 2-band EQ per effect
24-bit A/D and D/A converters with 64/128-times oversampling
True stereo processing for realistic channel separation in stereo image
100 factory presets plus 100 user memory locations
Extensive MIDI implementation
Accurate LED level meters for perfect level setting and optimum performance
Servo-balanced XLR and ¼'' TRS inputs and outputs
High-quality components and exceptionally rugged construction ensure long life
Conceived and designed by BEHRINGER Germany

 Reverbs & Delays

Because it is one of the most desired effects, the FX2000 provides 12 different reverb programs, so you always have the ideal reverb for your live performance or studio needs.

Reverbs include:

    CATHEDRAL
    GOLD PLATE
    SMALL HALL
    ROOM
    STUDIO
    CONCERT
    STUDIO
    STAGE
    SPRING REVERB
    AMBIENCE
    EARLY REFLECTIONS

Specialty reverbs include:

    REVERB – reverb is synthetically turned off after a predetermined amount of time
    REVERSE REVERB – reverb envelope is reversed—it slowly gets louder

Delays include:

    STEREO DELAY – delay is processed across the entire stereo image
    TAPE ECHO – simulates classic tape echo devices, pre-dating the advent of digital delays
    PING PONG – delay signal is "bounced” from left to right at an adjustable tempo

Much More than Just Reverb and Delay

The FX2000 has some of the best-sounding reverb and delay programs, but thatʼs not all. It also provides excellent modulation effects (such as chorus, flanger and phaser), including special variations like musical pitch shifter, tremolo and even a rotary speaker simulation.

Modulation and Pitch Shifter FX:

    STEREO FLANGER (originally generated by playing back two synchronized "reel to reel” tape recorders with a finger rubbing on the flange of one of the take-up reels)
    VINTAGE FLANGER simulates a guitar fl anger stomp box
    JET STREAM FLANGER sounds like a classic analog flanger
    STEREO CHORUS (combines a slightly detuned signal with the original)
    ANALOG CHORUS simulates a guitar chorus stomp box
    VINTAGE CHORUS imitates a classic analog studio chorus
    ULTRA CHORUS creates the sound of an eight person chorus
    STEREO PHASER (combines a second, phaseshifted signal to the original)
    VINTAGE PHASER represents a guitar phaser stomp box
    DUAL PHASER processes the left and right channels separately
    ROTARY (simulation of the rotating speakers typically used on an organ) – Slow or Fast
    PITCH SHIFTER (changes the pitch of the original signal) – can be used to create harmonies with the original signal or replace it entirely with the altered pitch. Choices include stereo, two and three vocal pitch shifter
    VIBRATO – the peak frequency of the tone is periodically and uniformly changed (quickly or slowly)
    TREMOLO (common vintage guitar amplifier effect) – a fast or slow periodic variation in volume
    AUTO PANNING – signal is automatically sent from one side of the stereo image to the other, either once or multiple times

Dynamic FX:

    COMPRESSOR – reduces the dynamic range of the signal, maintains consistent signal level and thus avoids distortion associated with excessive input levels
    EXPANDER – effectively broadens the dynamic range of source signals while reducing background noise
    GATED REVERB – helps reduce background clutter by turning reverb off below a predetermined threshold level. Particularly effective on drum mics and vocals
    ANA. KOMPR/LIM. — similar to COMPRESSOR but with Limiting functionality
    ULTRAMIZER – analyses incoming signal and automatically applies compression across two independent frequency bands
    DENOISER – eliminates or reduces noise and other interference
    DE-ESSER – reduces or removes sibilance (Ssss sound) from signal
    WAVE DESIGNER – allows you to influence the envelope by adjusting Attack and Release of the signal

Psychoacoustic FX:

    EXCITER – adds artificially generated overtones to the original signal, increasing presence and perceived loudness without significant increase in signal level
    ENHANCER – functions much like a dynamic pitch equalizer
    ULTRA BASS – sub-harmonic processor combined with bass exciter and limiter
    STEREO IMAGER – divides the signal into middle and side signals, allowing individual signals to be amplif ed when desired and placed on the stereo image
    ULTRA WIDE – creates a broader stereo image
    BINAURALIZER – also creates a broader stereo image and compensates for crosstalk between both speakers

Filter/EQ FX:

    AUTO FILTER – influences the frequency response of a signal. Two filters are included: low pass allows low frequencies to pass and suppresses high frequency content; high pass does the exact opposite
    LFO FILTER - Controls the rate of oscillation effects
    PARAMETRIC EQ – allows you to control the bandwidth, frequency and amplitude of a signal
    GRAPHIC EQ – the sound spectrum is divided into eight (8) adjacent frequency bands, which can be cut or boosted, bandwidth is predetermined

Distortion FX and Amp Simulations

The FX2000 is also equipped with distortion, amplifier and speaker simulation including VOCAL DISTORTION, TUBE DISTORTION, GUITAR AMP, TRI FUZZ, SPEAKER SIMULATION, RING MODULATOR and LO-FI.

Special FX:

    VINYLIZER – adds clicks and/or noise to the signal, reminiscent of old vinyl records and tape machines
    SAMPLER – allows you to record and playback up to five (5) seconds of program material
    VOCODER – allows the input signal to modulate another signal (usually a synthesizer sound), creating the familiar "talking synthesizer” effect
    VOICE CANCELER – removes mono vocal parts from stereo recordings for "instant Karaoke”
    RESONATOR – simulates and oscillating system that amplifies a specific frequency

Our FX Combinations Go to 11

Sometimes you want to add a little (or a lot) of color to your reverb and delay patches. The FX2000 allows you to layer modulation effects like chorus, flanger, pitch or tremolo with your reverb or delay selections.

FX Combinations include:

    Chorus & Reverb
    Flanger & Reverb
    Leslie & Reverb
    Pitch & Reverb
    Delay & Reverb
    Tremolo & Reverb
    Phaser & Reverb
    Chorus & Delay
    Flanger & Delay
    Pitch & Delay
    Tremolo & Delay

Enhanced User Editability
Logical grouping of parameters, along with the combination of encoders, buttons, LEDs and an easily readable LED display, make operating the FX2000 a breeze. You are free to edit up to seven parameters per preset, and then save them for future use in the 100 provided memory locations.
Value
With its extremely powerful processing capability and versatile array of features, the FX2000 will become the busiest tool in your audio arsenal. Stop by your BEHRINGER dealer today and find out why more professional sound engineers are turning to the FX2000 as their primary FX processor— both in the studio and on the road.

The S com 4 is a compact and versatile single-rack space device that provides
four channels of high quality dynamics processing with an Expander/Gate and
Compressor/Limiter on each channel.
The four channels operate independently or in stereo pairs. Its multi-segment LED
metering displays input/output level as well as gain reduction. The Expander/Gate
section features a continuously variable Threshold control as well as a switch for
fast or slow release times.
The Compressor/Limiter section includes variable Threshold, Ratio and Output levels.
S com 4's Enhancer switch restores high frequencies that are sometimes diminished
by heavy compression. This wide-ranging combination of features makes the S com
4 an efficient and versatile audio tool for a wide variety of applications. Its clean and
quiet audio characteristics make it ideal where high sonic integrity is imperative. 
 
FEATURES:

4 Channel Compressor/Limiter, Expander/Gate with Enhancer
Linkable in two Stereo pairs
Expander/Gate with variable Trigger control and switchable Fast/Slow Release
5 Segment LED meters for Input/Output levels and Gain Reduction on each channel
Advanced circuit design utilizing Low Noise Operational
Amplifiers and High Quality VCA's
Servo Balanced Inputs and Outputs on XLR and 1/4" connectors
SKD (Smart Knee Detector) circuit automatically switches from soft to hard knee
based on the level of Input signal applied
Individual Threshold and Ratio controls on each channel
Three-year extended warranty 

Innovation

The ARX AFTERBURNER? is a unique Multi Mode compressor/limiter
designed for use in any professional audio dynamics control application.
Multiple Modes
The Afterburner can be set up and used in three different ways:
In Two channel mode, it performs as two independent compressor/limiters,
with 'industry standard' variable Threshold, Ratio and Output gain. In stereo
mode, our New Adaptive Stereo Link circuitry provides increased stereo
imaging accuracy when linking both channels as a stereo pair. A single front
panel switch puts the Afterburner into its alternative Mono mode, setting it up
as a Single channel, Dual Band compressor/limiter, with separate dynamics
control of both Low and High frequencies, opening up a whole new range of
gain control techniques.
Enhance Switch
In any mode, the Afterburner features an 'Enhance' switch, which provides
frequency restoration to preserve the spectral balance of the audio signal,
compensating for the sagging Low and High frequency response of compressed
program material. Think of it as a 'smart' loudness control.
 
Features
Switchable Modes - Stereo; Dual Channel Single band; or Single Channel
Dual Band (Low and High)
Low and High frequency compression in Single Channel mode
'Enhance' switch restores spectral balance of compressed signal
New Hard/Soft knee compression switch
New Adaptive Stereo Link circuit for accurate stereo imaging
New Above/Below Threshold LEDs enable at-a-glance compression
confirmation
Balanced XLR and Jack Inputs and Outputs
Sidechain Insert points
Intuitive user-friendly layout
Flawless performance
 
New Above/Below Threshold LEDs enable at-a-glance compression confirmation
New Hard or Soft knee compression option
New LED metering provides accurate Level status, with separate Gain Reduction
metering in easy to read 'wide scale' meters. There is also comprehensive LED
indication of all operating functions and status in any mode.
Balanced Inputs and Outputs
On the rear panel, each channel has true differential Balanced inputs and outputs,
on both XLR and TRS jack connectors. As well, each channel has a TRS jack
Sidechain access insert point, for applications such as De-essing (when used with
an external equalizer such as the ARX Multi Q or EQ 260).Other features include a
true Hardwire bypass switch for each channel, and passive RFI filters on the inputs.
Universal AC Power
AC power range is a universal 100 to 120V or 220 to 240V AC, and is connected to
the unit via a removable power lead and standard 3 pin IEC connector, with built-in
fuse and voltage change switch.
With its smooth compression, intuitive user friendly layout, high density precision
circuitry, and extensive user-variable operating parameters, the unique ARX Afterburner
is equally at home in Studio, Installation, Broadcast and Sound Reinforcement
environments. It can provide great sounding dynamics control effects that are not
available with any other device.
 
T E C H N I C A L  S P E C I F I C A T I O N S
Input Impedance Balanced 20 Kohms, Unbalanced 10 Kohms
Input Headroom + 22 dB
CMRR >60 dB, 20 Hz-20 KHz
Output Impedance Balanced 300 ohms, Unbalanced 150 ohms
Output Level (Max) + 22 dB
Frequency Response 20Hz to 20KHz ±0.2dB
Signal to Noise ratio -93 dB Unweighted, -99 dB 'A' weighted
Distortion .02% THD @ 0dB,1KHz
Dynamic Range 115 dB
Sidechain Insert Impedance 10 Kohm
Filter Section
Filter Type Phase corrected 6dB/octave
Summed Filter Response ±0.2dB through crossover region
Dividing Frequency 250 Hz
Enhance Section
Low Enhance 50 Hz, High Enhance 10 KHz
Power Requirements 100/120 V AC, 220/240 V AC
Weight 5 lbs/2.2 Kg
Dimensions 19“W x 1?“H x 6“D, 482 x 44 x 155mm
Input/OutputConnector type XLR, Balanced Jack
Sidechain Insert Connector TRS Jack

Front Panel Controls
Hardwire bypass IN/OUT switch
Threshold, Ratio and Output Gain controls
Above/Below Threshold LEDs
12 segment LED Output Level display
Numbered marker panel for labelling compressor assigns
7 segment LED Gain Reduction display
Enhance switch and status LED
Adaptive Stereo link switch and status LED
Dual/Single channel mode switch and status LEDs
Rear Panel Connectors
Balanced Inputs and Outputs, on both XLR and TRS jack
connectors. In Single channel (Mono) mode, use Channel
1 Inputs and Outputs only
Sidechain Insert TRS connector on each channel
AC input connector, with voltage switch and fuse.