DBX 1074 NOISE GATE USED (Made in USA)

• Four independent channels of gating
• Independent key filtering
• Independent Threshold and Release controls
• Differentially balanced gold-plated XLR and 1/4" inputs and outputs
• True RMS level detection
• Stereo Coupling mode
• Switchable +4dBu or -10dBv operation per channel

  Input Connectors	XLR (Pin 2 and tip hot)
  Input Type	Electronically balanced/unbalanced, RF filtered
  Input Impedance	Balanced > 50 kOhm, unbalanced >25 kOhm
  Max Input	> +22 dBu balanced or unbalanced
  CMRR	40dB: Typically >55 dB at 1 kHz
  Key Input	Electronically balanced/unbalanced, RF fitered Balanced 50kOhm, unbalanced > 25 kOhm
  Output Connectors	XLR (Pin 2 hot)
  Output Type	Servo-balanced/unbalanced, RF filtered
  Output Impedance	Balanced 60 Ohm, unbalanced 30 Ohm
  Max Output	> +22 dBm balanced, > +20 dBm unbalanced
  Bandwidth	20 Hz to 20 kHz, +0/-0.5 dB
  Frequency Response	0.35 Hz to 200 kHz, +0/-3 dB
  Noise
  Dynamic Range	> 115 dB, unweighted
  THD+Noise	0.008% typical at +4 dBu (1 kHz unity gain), 0.08% typical at +20 dBu (1 kHz unity gain),
  Interchannel Crosstalk
  Stereo Coupling	True RMS Power Summing
  Operating Voltage	100-120 VAC 50-60 Hz or 200-240 VAC 50/60 Hz
  Power Consumption	30 Watts
  Fuse	100-120 VAC:250 mA Slow Blow, 200-240 VAC:125 mA Type T
  Power Connector	IEC receptacle
  Unit Weight	6.9 lbs.
  Shipping Weight	9.3 lbs.

   

Interactive Reference-Class 2-Channel Expander/Gate/Compressor/ Peak Limiter with
Integrated De-Esser, Dynamic Enhancer, Tube Simulation and Low Contour Filter 

Whether you?re recording, mixing or mastering, the COMPOSER PRO-XL MDX2600
gives you total dynamic control. It includes all of the features you would expect from
a reference class compressor?plus a voice-adaptive de-esser, a new dynamic
enhancer, authentic tube emulation and much more. These are some of the indispensable
tools for producing clean, consistent audio with virtually no loss in signal quality.

Features:
Switchable IKA (Interactive Knee Adaptation) program-adaptive compression circuitry
combines the advantages of hard-knee and soft-knee characteristics
Integrated de-esser with switchable male/female voice recognition removes excessive
sibilance from your vocal tracks
IGC (Interactive Gain Control) peak limiting circuitry combines clipper and program
limiter for reliable and inaudible protection against signal peaks
Switchable dynamic enhancer for brilliant, lively audio even with heavy compression
IRC (Interactive Ratio Control) expander/gate circuitry for virtually inaudible
noise suppression
Switchable tube simulation for the extra warmth and transparency of classic
tube circuitry
Automatically or manually adjustable attack and release times
Switchable low contour filter prevents "pumping" due to low-frequency
dominated compression
Stereo couple function with independent output level settings
Switchable side chain input with side chain monitor function
Ultra low-noise 4580 operational amplifiers and state-of-the-art THAT¬ VCA's
Separate 12-segment LED meters for input/output levels and gain reduction
Dedicated "traffic light" threshold and de-esser level displays
High-quality detented ALPS¬ potentiometers and illuminated switches
Servo-balanced inputs and outputs with ? in. TRS and gold-plated XLR
connectors
Relay-controlled hard bypass switch with auto bypass function in case
of power failure
Manufactured under ISO9000 certified management system
 

• Professional 31-band stereo graphic equalizer for live and studio applications
• Revolutionary FBQ Feedback Detection system instantly reveals critical frequencies and can also be used as audio analyzer
• Ultra-low noise 4580 operational amplifiers for highest signal integrity
• Dedicated mono subwoofer output with adjustable crossover frequency
• Additional sweepable high and low-cut filters for each channel remove unwanted frequencies, e.g. floor rumble, hiss etc.
• Highly accurate 12-segment LED input/output metering and input gain controls for easy level setting

• Relay-controlled hard-bypass with an auto-bypass function during power failure (fail-safe relay)
• Servo-balanced inputs and outputs with 1/4" TRS and gold-plated XLR connectors
• “Planet Earth" switching power supply for maximum flexibility (100 - 240 V~), noise-free audio, superior transient response plus low power consumption for energy saving
• 3-Year Warranty Program*
• Conceived and designed by BEHRINGER Germany

The DPR-504 is a 4-channel noise gate.

Each channel features:
A parametric key filter with key filter listening.
Simultaneous key level and threshold metering with average and
peak metering.
A gate status LED.
A RELEASE/HOLD control (hold tracks proportionally with release
times).
Attack switchable auto/fast (auto tracks signal dynamics for optimum
setting).
Link (links two channels together).
Key source allows external triggers.

The Range switch selects between 7OdB and 2OdB gating depth to
provide alternative release profiles.
The unit features electronically balanced inputs and outputs. 

Features
Enhance switch to restore spectral balance of compressed signal
Switchable Mode - Dual Channel or Stereo linked
Above or Below Threshold LEDs
Balanced XLR and Jack Inputs and Outputs
Intuitive, user friendly layout
Flawless performance

Innovation
The ARX COMPO? is a unique compressor/limiter designed for use in any
professional audio dynamics control application, packaged in a compact 1
RU chassis.The COMPO operates as two independent compressor/limiters,
with 'industry standard' variable Threshold, Ratio and Output gain controls.
A Stereo Link switch on the front panel lets both channels track as a stereo
pair in a Master/Slave configuration.
Enhance Switch
The COMPO features an 'Enhance' switch, which provides frequency restoration
to preserve the spectral balance of the audio signal, compensating for the sagging
Low and High frequency response of compressed program material.
The best way to think of it is as a 'smart' loudness control.
Wide Scale metering
There is comprehensive LED indication of all operating functions and status. Above
or Below Threshold LEDs on each channel give you instant visual confirmation of
compressor activity, as well as easy to read LED Gain Reduction meters.
Balanced Inputs and Outputs
On the rear panel, each channel has true differential Balanced inputs and outputs,
on both XLR and TRS jack connectors. Other features include an Active/Bypass
switch for each channel, and passive RFI filters on the inputs.
Universal AC Power
AC power range is a universal 100 to 120V or 220 to 240V AC, and is connected to
the unit via a removable power lead and standard 3 pin IEC connector, with built-in
fuse and voltage change switch.
ARX Quality
With its smooth compression, intuitive user friendly layout, high density precision
circuitry, and extensive user-variable operating parameters, the ARX COMPO is the
ideal installation 'set and forget' compressor, and is also equally at home in Studio,
Broadcast and Sound Reinforcement environments.

Every day, ARX Audio interface products solve audio problems for thousands of people
around the world.

T E C H N I C A L S P E C I F I C A T I O N S
Input Impedance Balanced 20 Kohms, Unbalanced 10 Kohms
Input Headroom + 22 dB
CMRR >60 dB, 20 Hz-20 KHz
Output Impedance Balanced 300 ohms, Unbalanced 150 ohms
Output Level (Max) + 22 dB
Frequency Response 20Hz to 20KHz ±0.4dB
Signal to Noise ratio -85 dB Unweighted, -99 dB 'A' weighted
Distortion .02% THD @ 0dB,1KHz
Dynamic Range 107 dB
Enhance Section
Low Enhance 50 Hz, High Enhance 10 KHz
Power Requirements 100/120 V AC, 220/240 V AC
Weight 5 lbs/2.2 Kg
Dimensions 19“W x 1?“H x 6“D, 482 x 44 x 155mm
Input/OutputConnector type XLR, Balanced Jack

Front Panel Controls
Channel A Active/Bypassed IN/OUT switch
Threshold, Ratio and Output Gain controls
Numbered marker panel for labelling compressor assigns
5 segment LED Gain Reduction display
Above/Below Threshold status LEDs
Enhance switch and status LED
Stereo link switch and status LED
Channel B controls identical to Channel A
Rear Panel Connectors
Balanced XLR Input and Output connectors.
Balanced TRS jack Input and Output connectors.
AC input connector, with voltage switch and fuse.
 

OPTIMOD-FM 5500 puts coveted five-band and two-band OPTIMOD processing into a single rack unit package and brings it to you at the most affordable price ever.

Quality sound is what 5500 is all about-sound that attracts audiences by providing a polished, professional presentation regardless of format and source material. Exceptional versatility allows you to adjust the processor's audio texture to brand your audio, knowing that the resulting signature sound will remain consistent, cut-to-cut and source-to-source. Branding builds businesses and no other processors have the consistency to brand your sound like OPTIMOD.

With the 5500, your signature sound is just a preset away. An easy, one-knob Less/More adjustment allows you to customize any factory preset, trading cleanliness against processing artifacts according to the requirements of your market and competitive environment. Full Control gives you the versatility to customize your audio further. And, if you're a hard-core processing expert, you can explore Advanced Control to tweak presets at the same level as Orban's factory programmers. This versatility makes the 5500 a superb choice for any format. Its five-band processing is ideal for any pop music format (even the most competitive and aggressive CHR), while phase-linear two-band processing yields ultratransparent sound for classical, classic jazz, and fine arts formats. Regardless of your choice, 5500's optimized technology ensures unusually high average modulation and coverage for a given level of subjective quality. Unlike many lesser processors, the 5500 handles speech particularly well. It's always clean, even when you process for loudness.

If you're concerned about latency because you need to feed live talent headphones off air, be assured that the 5500's ultra-low-latency (5 ms delay) processing will keep the most finicky talent happy. Or use optimum latency (15 ms delay) processing for the most competitive sound with delay that's still low enough to satisfy most any talent.

The 5500 can also be used as a superb stand-alone stereo encoder with latency as low as 2 ms and full overshoot limiting in both the left/right and composite baseband domains.

When used in this mode, the 5500 must be driven (usually via an STL) by a full-featured FM audio processor (like Orban's 8600) that incorporates pre-emphasis aware HF limiting and peak control. In both modes, the 5500's stereo encoder helps deliver a transmitted signal that's always immaculately clean and perfectly peak limited, with full spectral protection of subcarriers and RDS/RBDS regardless of the amount of composite limiting.

It is the ideal choice for network broadcasters who process with Orban's flagship OPTIMOD-FM 8600 at the network origination point and who need a processor at every transmitter to eliminate STL overshoots (using the 5500's stand-alone stereo encoder mode) and/or to process local insertions while also eliminating network STL overshoots (using the 5500's audio processor / stereo encoder mode). Moreover, the 5500's two modes make it easy for large government and network broadcasters to manage its inventory of spares because any 5500 can be used as a stereo encoder with or without audio processing.

Available in both modes, the built-in, defeat-able ITU-BS412 multiplex power controller allows the 5500's output to meet even the most stringent European government regulations.

A 10 MHz frequency reference input allows the stereo pilot tone frequency to be locked to GPS or another high-accuracy frequency standard. This improves the performance of single-frequency networks in areas where coverage of the transmitters overlaps.

The 5500's built-in stereo encoder, AES/EBU digital inputs and outputs, and analog I/O permit hasslefree interfacing to any broadcast plant, whether the 5500 is located at the studio or the transmitter. Tight band limiting to 15 kHz means you can use any uncompressed digital STL to pass 5500- processed audio from studio to transmitter without compromising on-air loudness - there's no need to use STL's having 44.1 or 48 kHz sample-rate.

The stereo encoder's stereo sub-channel modulator can operate in normal double sideband mode and in an experimental compatible single sideband mode (SSB/VSB) that is offered to enable users to compare and assess the two modes.

Analog Fallback to Digital control that allows Silence Sense to switch the active input from Analog to Digital if silence is detected in the analog input signal but not on the digital input signal. This function works vice versa as well on both analog and digital AES input. The silence sense parameters apply to both simultaneously and both detectors are available to drive the 5500's tally outputs and sending SNMP Traps/Alerts.

If you want to locate the 5500 away from the studio, you'll be pleased by its three separate remote control ports - GPI contact closures, RS232 serial and built-in Ethernet for TCP/IP networks. The serial and Ethernet ports are supported by the supplied 5500 PC Remote Control application. This Windows® 2000/XP/Vista/7/8 application allows you to do even more with the 5500 than you can do through its front panel, making remote control a pleasure.

5500 PC Remote software allows you to access all 5500 features and allows you to archive and restore presets, automation lists, and system setups (containing I/O levels, digital word lengths, GPI functional assignments, etc.)

Built-in clock-based automation lets you automatically day-part the processing. You can control many other 5500 operating parameters too.

The 5500's feature set fully exploits the processor's DSP and computer-based control architecture. To ensure absolute accuracy, you can automatically synchronize the clock to an Internet timeserver. It has a cool-running, energy-efficient switching power supply and uses the latest dual-core DSP chip technology from Freescale Semiconductor.