| Content |
- 2x500W Power Amp
- 8 Mic/Line Inputs
- 2 Stereo Inputs
- 1 Aux / FX Send
- 9 Band Graphic EQ
- Record Bus
- USB Recording / Playback
- Touring Grade Build Quality
- 2 Line Inputs with Class A high impedance for ultimate guitar tone
- 3 Band British EQ with Swept Mid
- 16 Studio Quality FX with Tap Tempo
| DYNACORD POWERMATE 600-3 COMPACT POWER MIXER.2X340W-4ohms Original 3 years warranty of Greek distributor
This extremely compact powered mixer is the youngest member of the PowerMate3 family. With a total output of 2,000 watts, it is far and away the most powerful compact mixer on the world market, yet it weighs only 9kg! With its very lavish feature set and exemplary versatility it is the ideal choice for all professional applications in which few channels yet very high audio quality are required.
Performance without compromises: intuitively operated mixing section; 2 editable digital effects devices with 100 presets each and 20 user memories each; professional 4xIN / 4xOUT digital interface (USB) for the connection of a PC or Mac; stereo equalizer in the master section; large, contrast-rich OLED display; and a class-D high-performance power amplifier delivering 2 x 1,000 watts RMS into 4 ohms. Exclusively high-quality brand components have been used; all faders and potentiometers are supplied by ALPS.
In the mixer section, a total of 8 channel strips are available: 4 MIC / LINE channels, 2 MIC / Stereo USB channels ('Super Channels') and 2 stereo LINE channels.
The MIC / LINE channels offer extremely low-noise and low-hum electronically balanced XLR microphone inputs with an extremely low distortion factor (typ. < 0.002%) for the connection of low-impedance microphones. For condenser microphones, phantom power (+48 volts) is centrally switchable. The LINE inputs are also electronically balanced and implemented as jack sockets. In addition to a Gain control, a highly efficient 3-band equalizer, an FX send, an AUX send and a MONitor send as well as either Panorama or Balance controls are available. The four MIC / LINE channels boast, in addition, a switchable 80Hz Lo-Cut filter, whilst the Super Channels 5-6 and 7-8 are supplied by the USB inserts 1-2 and 3-4, in each case in stereo.
The STEREO-LINE channels (9-10 and 11-12) offer electronically balanced jack inputs for the connection of electronic instruments such as keyboards, drum-computers, guitars and basses with active electronics, as well as all other high-level stereo signal sources such as additional mixers, effects devices etc. CD or MP3 players can be connected to the additional cinch (RCA) inputs CD 1-2 and CD 3-4, which are switched in parallel. The tone controls and sends are identical to those of the MIC / LINE channels.
In all input channels, a Signal / Peak LED is provided to assist level control. The SIG LED illuminates at around 30 dB and the PK LED at 6dB beneath the distortion threshold. A MUTE button and a PFL button (in channels 5-12 in stereo) are further features found in all input channels.
The DIGITAL AUDIO INTERFACE supplies two stereo channels, present as USB 1-2 and USB 3-4 in Super Channels 5-6 and 7-8 respectively. This interface is implemented professionally in 24-bit resolution and supports sampling rates up to 96 kHz, thereby satisfying studio requirements. The USB sends are supplied with the Master L and R, AUX and MON signals. The DIGITAL AUDIO INTERFACE can be used for input and output simultaneously. Via the USB 2.0 port of your PC / Mac, four channels can be transmitted simultaneously in each direction. When a USB 1.1 interface is used, two channels can be transmitted simultaneously in each direction. The PowerMate is designed for the level of standard PCs / Macs; the gain level can easily be adjusted, if need be, from the computer connected.
Included in the delivery is a DVD containing the professional recording software Cubase LE and PC / Mac USB drivers.
PC MIDI Interface
The PowerMate also makes available a fully-featured PC MIDI interface.
The MIDI input also supports the remote switching of both internal effects units using a master keyboard or MIDI footswitch.
In the PowerMate's Master Section are to be found the Master A L+R sends (on separate faders), an additional Master B send (switchable pre/post and mono/stereo), the stereo effects returns, and the send signals of the AUXiliary and MONitor busses. If the AUX buss is not used to supply FX 2, it can be switched pre or post and thereby used as an additional monitor send or to supply an external effects device.
The 9-band stereo equalizer in the master section allows you to adjust the frequency response to the acoustics of the room.
The REC SEND and USB OUT controls determine the level of the master L+R signal at the Rec Send sockets and in the output channels of the digital USB interface. The control below it allows you to adjust the volume in the headphones.
Two ten-LED meters provide an overview of the power amplifier level. When the PFL switch is activated, the left-hand LED chain shows the internal level of the master buss in dBu.
The STANDBY switch mutes all outputs. For the playback of things like interval music, the DEVICE SETUP menu allows you to route stereo channel 11-12 for standby operation directly to the power amplifiers.
The PowerMate is equipped with two very high-quality, 24-bit stereo effects processors, FX 1 and FX 2; these function independently and can therefore be mixed. The two effects units are fully identical in design. Each effects section offers 100 presets including high-quality reverb, delay and modulation effects selected by means of the display. When a delay effect is active, the delay time can be synchronized to the beat of the music using the TAP key. The further possibility exists of modifying individual parameters of the presets and storing the results in the 20 user memories provided.
Both effects units are supplied by the FX Send buss. Using the DEVICE SETUP menu, you can, if you wish, configure the AUX send buss to function as an FX 2 send, so that only the FX 1 effects unit is supplied by the FX 1 buss. In this way, the two effects devices can be controlled independently of one another.
The effects can be mixed separately in the master and monitor busses.
The large, high-contrast OLED display is easily read from a wide range of viewing angles—even in very bright surroundings. The operation of the effects units and processing menus is intuitive and made easier still through the use of soft keys and a rotary encoder.
Processing Menus: Particularly valuable in making it possible to adjust the PowerMate perfectly to the selected loudspeaker cabinets, thereby optimizing the audio performance and maximizing the operating safety and reliability of the system, are the LPN Processing and Speaker Protection menus.
LPN processing
Typical small to medium-sized loudspeaker cabinets, for physical reasons that have nothing to do with their make or quality, exhibit distortion in the transient response of the woofer. Since neither graphic nor parametric equalizers can do anything to alleviate this problem, the PowerMate offers a configurable LPN (low-pass notch) filter. Depending upon the size of the loudspeaker cabinet being used and also to adjust to problematic acoustics (such as those of bassy, boom-ridden rooms), the LPN filter can be set to either High or Medium. The result is considerably greater punch (e.g. from the bass drum), an extension downwards of the frequency response, and improved transparency in the bass and midrange.
Speaker Protection
This menu allows you to match perfectly the continuous power output of the PowerMateʼs power amplifiers to the connected loudspeakers in the interests of greater operational safety and reliability.
Through dynamic limiting of the maximum power at the output, loudspeaker damage due to thermal overload can be avoided, without the wide dynamic range of the power amplifiers being sacrificed. For this purpose, the maximum permissible nominal power handling of the connected loudspeaker cabinet can be selected from the menu. Unlike the case with conventional voltage limiters, dynamic peaks of short duration are permitted, as loudspeaker cabinets can as a rule tolerate peak levels many times higher than their nominal sustainable loads (RMS).
The speaker protection supervises permanently the amount of energy being fed to the loudspeakers, only limiting it in the event of a threatened overload, and even then, doing so softly and inaudibly. For peak levels of short duration, the full output of the power amplifier remains available at all times, even when relatively small cabinets are being used. As a result, not only is the maximum dynamic range of the system maintained but also, and at all times, the highest degree of operational safety and reliability.
Professional Digital High-Performance Power Amplifier
The PowerMate is equipped with a professional, extremely powerful, stereo power amplifier that uses modern and highly efficient class-D technology for audio performance of the highest quality.
What this means is that at a nominal output of 2 x 1,000 watts RMS into 4 ohms (or 2 x 1,350 watts RMS into 2.7 ohms) only a comparatively small amount of heat is generated within the device, which therefore consumes considerably less electricity than a conventional power amplifier. The minimal load impedance at the output is 2.7 ohms, making operation with up to three 8-ohm loudspeaker cabinets per channel, connected in parallel, possible with no problems.
The overall power supply is handled by an extremely stable, microprocessor-controlled, switching power supply, bringing massive gains in terms of weight-saving over a conventional toroidal transformer. Another advantage is the automatic mains voltage switching, which ensues that the PowerMate can be used without any problem anywhere in the world. Voltage surge protection is also integrated. A ʽsoft startʼ function prevents the mains fuse tripping when the device is switched on.
The PowerMate is equipped, naturally, with all the protective circuitry familiar from DYNACORD power amplifiers and satisfies even the extreme demands of hard tour use. The power amplifiers are protected against thermal overload, short-circuit, back EMF and no-load operation as well as high-frequencies or DC at the output. Both outputs, here, are supervised independently so that, should a fault occur, only the channel affected is shut down. When the device is powered up, there is a delay before the power outputs are connected, to obviate the risk of noise.
The thermal stability of the PowerMate is assured by two very quiet fans the speed of which is continuously variable. The front-to-rear airflow allows the device to be used in large or small racks. Furthermore, the PowerMate is equipped with an intelligent thermo-limiter, so if ever the threat of overheating does arise, the clip limiter intervenes in a highly musical way, acting only upon the peaks. In this way, a total shutdown of the power amplifiers is effectively prevented, as is any obtrusive fall in the overall volume level. The PROTECT and LIMIT LEDs on the front panel indicate the current operating state of the power amplifiers.
To ensure safe transportation, the PowerMate 6003 is supplied with a solid plastic lid that is held in place simply and securely, without the need for any locking mechanism, by magnets.
Available as an optional accessory, the carrying bag BAG-600PM not only accommodates the PowerMate with its lid but also offers an additional compartment for cables etc.
For rack installation, the RMK-PM600-3 rack-mount kit is available as an option.
Order No. F01U213899 (DC-PM600-3-UNIV)
Channels (Mono + Stereo) 4 + 4
Auxiliarys (MON, FX, AUX) 1 Pre, 1 Post, 1 Pre/Post switchable
Maximum Midband Output Power, 1 kHz, THD = 1%, Dual Channel into 4 Ohms 2 x 1000 W
Power Requirements (SMPS with auto range mains input) 100 V to 240 V AC, 50 Hz to 60 Hz
Power Consumption, at 1/8 maximum output power, 4 Ohms 450 W
Dimensions with lid (W x H x D), mm 438.8 x 161.7 x 362.5
Net Weight, without lid 9.0 kg
complete specifications see download section, Datasheet EDS
User's Manual |
A professional mixer offering two digital effect units and a 2 x 300 watts power amplifier to be used in entertainment and multimedia applications. Whether it is being used as mobile DJ-mixer, by a rental company, in a clubhouse, a hotel, a club / bistro, or in the party cellar at home: the comprehensive set of features and professional audio quality of the MP-7 Entertainment System also solves your sound reinforcement problem.
Maximum Midband Output Power, 1 kHz, THD = 1%: - into 4 ohms 2 x 340 W into 8 ohms 2 x 200 W Rated Output Power, 20Hz… 20 kHz, THD =0.2%: - into 4 ohms 2 x 300 W into 8 ohms 2 x 150 W Maximum Output Voltage of the power amplifier, no load THD @ 1 kHz, MBW=80kHz 43 Vrms MIC input to Main L/R output, +16 dBu 90 dB Channel seperation > 70 dB Input Sensitivity, all level controls in max. position: - MIC input -74 dBu (155µV) Line Input (Mono) -54 dBu (1.55 mV) CD/MD Line Input (Stereo) -24 dBu (49 mV) Phone Input (Stereo) -61.5 dBu (652 µV) Power Amplifier Input +6 dBu (1.55 V) Maximum Level, mixing desk: - MIC inputs +11 dBu Line inputs +30 dBu All other inputs +20 dBu Record Send output +14 dBu All other outputs +20 dBu Input Impedances: - MIC 1.8 kohms All other inputs > 10 kohms Output Impedances: - Record Send 1 kohms Phones 47 ohms All other outputs 75 ohms Equivalent Input Noise, MIC Input, A-weighted 150 ohms -130 dBu Noise, Channel inputs to Main L/R outputs, A-weighted: - Master fader down -104 dBu Master fader 0 dB, Channel fader down -91 dBu Master fader 0 dB, Channel fader 0 dB, Channel gain unity -84 dBu Signal/Noise-Ratio, power amplifier, A-weighted 105 dB Equalization STEREO: - LO Shelving +9/-30 dB / 60 Hz MID Peaking +9/-30 dB / 2.4 kHz HI Shelving +9/-30 dB / 12 kHz Equalization MIC: - LO Shelving ±15 dB / 60 Hz MID Peaking ±12 dB / 2.4 kHz HI Shelving ±15 dB / 12 kHz Master EQ, 2x7-band, Stereo ±10 dB Phantom Power, all MIC Inputs +24V dc Lamp +12V dc Power Requirements, factory preset, 50Hz....60Hz 100V/120V/230V/240V Power Consumption at 1/8 maximum output power 4 ohms 450 W Dimensions, (WxHxD), mm 455,5 x 175,8 x 340.6 Weight, including lid 13 kg Optional Rack-Mount-Kit MP7
| PowerMate 1000
SPECIFICATIONS
Order No.
F01U131113 (DC-PM1000-3-UNIV)
Channels (Mono + Stereo)
6 + 4
Auxiliaries (MON, FX, AUX)
2 Pre, 2 Post, 2 Pre/Post switchable
Maximum Midband Output Power,1 kHz, THD=1%, Dual Channel
into 2.66 Ohms
2 x 1350 W
into 4 Ohms
2 x 1000 W
into 8 Ohms
2 x 600 W
Rated Output Power,THD=0.1%, Single Channel
into 4 Ohms
2 x 900 W
into 8 Ohms
2 x 450 W
Maximum Output Voltage of power amplifier, no load
74 Vrms
THD at 1kHz, MBW=80kHz
MIC input to Master A L/R output, +16 dBu, typical
< 0.005%
POWER AMP INPUTS to Speaker L/R output
< 0.075%
DIM 30, power amplifier, 60Hz, 7kHz
< 0.05%
IMD-SMPTE, power amplifier, 60Hz, 7 kHz
< 0.015% CMRR, MIC input, 1 kHz > 80 dB
Equivalent Input Noise, MIC Input, A-weighted, 150 Ω
-130 dBu
Signal/Noise-Ratio, power amplifier, A-weighted, 4 Ohms
105 dB
Output Stage Topology, amplifier
Class D
Equalization
LO Shelving
+/- 15 dB / 60 Hz
MID Peaking, mono inputs
+/- 15 dB / 100 Hz .. 8 kHz
MID Peaking, stereo inputs
+/- 12 dB / 2.4 kHz
HI Shelving
+/- 15 dB / 12 kHz
Master EQ, 11-band (63, 125, 250, 400, 1k, 1.6k, 2.5k, 4k, 6.3k, 12k Hz)
+/- 10 dB / Q = 1.5-2.5
Filter
LO-CUT, mono inputs
f=80 Hz, 18 dB/oct
VOICE FILTER, mono inputs
FEEDBACK FILTER, MON1/2
70 Hz .. 7 kHz, Notch, -9 dB
Speaker Processing
LPN, switchable
Display
High Contrast OLED
Effects | Product Highlights
- Integrated 1260 W Power Amplifier
- 8 Mono Mic/Line Inputs
- Four Stereo Inputs
- Hi-Z Input on Channel 4
- Two Aux Sends w/ Dedicated Outputs
- 3-Band EQ on Each Channel
- Master EQ for Music Playback or Speech
- Integrated Feedback Suppressor
- Built-In SPX Multi-Effects
- Compatible with 4 and 8 Ohm Speakers
|
- 1,000 Watts RMS, 1500 Watts peak
- Subwoofer line output
- Monitor send
- Digital effects
- 8 Combination XLR/1/4 inputs
- Input pads
- Analog record output capability
- Front panel effects defeat
- FLS? exclusive feedback detection circuit
- Footswitchable effects defeat
- Dual 9-Band Main/Mon Graphic EQ
- Individual signal and clip detection LEDs
- Effect to monitor return
- Individual signal and clip detection LEDs
- Bluetooth? capability
- Four twist lock outputs
- Footswitchable master mic mute
- Optional rack mount kit available
- MidMorph? EQ
- KOSMOS? bass enhancement
- USB MP3 Player
- Selectable Main/Main or Main/Monitor power amp modes
- 3-Band EQ per channel
- Product Dimensions: 39.37 cm x 23.81 cm x 19.69 cm
- Weight Packed: 7.3 kg
- Width Packed: 34.29 cm
- Height Packed: 48.26 cm
- Depth Packed: 30.48 cm
|
Reviews
There are no reviews yet.