Content |
This low-profile cardioid condenser boundary microphone is recommended for unobtrusive table-, ceiling-, or panel-mount applications in high-quality sound reinforcement, professional recording and teleconferencing. Designed for permanent installation, the microphone is equipped with a self-contained power module with an XLRM-type output connector, eliminating the need for an external power module. Protected by a rugged all-metal case with a two-layer steel mesh grille, the microphone has a cardioid pattern for enhanced gain before feedback and improved signal-to-noise ratio. It is available in two colors: black (ES947) and white (ES947W).
- Designed for surface-mount applications such as high-quality sound reinforcement, professional recording and teleconferencing
- Low-profile element provides uniform cardioid polar pattern with 120º acceptance angle
- Mounts unobtrusively in table-tops, ceilings and wall panels
- Self-contained power module with XLRM-type output connector
- Rugged all-metal case with a two-layer steel mesh grille
- Isolators provide mechanical dampening of mounting-surface vibration
- Requires 11V to 52V DC phantom power
- UniGuard® RFI-shielding technology offers outstanding rejection of radio frequency interference (RFI)
- Available in two colors: black (ES947) and white (ES947W)
- RoHS compliant - free from all substances specified in the EU directive on hazardous substances
- Element: Fixed-charge back plate, permanently polarized condenser
- Polar Pattern: Half-cardioid (Cardioid in hemisphere above mounting surface)
- Frequency Response: 40-12,000 Hz
- Open Circuit Sensitivity: -42 dB (7.9 mV) re 1V at 1 Pa
- Impedance: 200 ohms
- Maximum Input Sound Level: 142 dB SPL, 1 kHz at 1% T.H.D.
- Dynamic Range: 113 dB, 1 kHz at Max SPL
- Signal to Noise Ratio: 65 dB, 1 kHz at 1 Pa
- Phantom Power Requiremens: 11-52V DC, 2 mA typical
- Weight: 64 g (2.3 oz)
- Dimensions: 69.0 mm (2.72“) long, 30.0 mm (1.18“) diameter
- Output Connector: Integral 3-pin XLRM-type
|
With three cardioid condenser elements in a single housing, the phantom-powered U843R offers a remarkably versatile tool for surface-mount installations. Levers on the microphone base allow easy reorientation of two elements to offer 360° or 300° coverage. Since elements can be powered and used individually or in any combination, further flexibility is easily achieved. For example, with two elements powered, the microphone can provide a figure-of-eight polar pattern; with a single element powered, the microphone functions as a standard cardioid boundary microphone. Installation and repositioning are extremely quick, thanks to four recessed pathways on the base of the microphone that enable the user to route the cable as required to accommodate any installation requirements; no tools or disassembly are needed. The microphone also offers Audio-Technicaʼs innovative UniGuard® RFI-shielding technology.
- Three cardioid condenser elements mounted in a single housing
- Easily reposition two elements (via levers on the microphone base) to offer 360° or 300° coverage; each element can be powered and used individually or in any combination
- Also functions as a stereo boundary microphone
- Provides full, efficient and flexible coverage—fewer microphones required
- Small-diameter capsules near boundary eliminate phase distortion and deliver clear, high-output performance
- Low-frequency attenuation improves sound pickup without affecting voice quality
- Cable routes through any of four recessed pathways on the microphone base (or down for direct feed through a table surface); no tools or disassembly required
- UniGuard® RFI-shielding technology offers outstanding rejection of radio frequency interference (RFI)
- Heavy die-cast case and non-slip silicone foam bottom pad minimizes coupling of surface vibration to the microphone
- Low-profile design with low-reflectance finish for minimum visibility
- Element: Fixed-charge back plate, permanently polarized condenser
- Polar Pattern: Hemispherical Cardioid x3 (combine to omni-directional or bidirectional)
- Frequency Response: 70-16,000 Hz
- Open Circuit Sensitivity: –37 dB (14.1 mV) re 1V at 1 Pa
- Impedance: 100 ohms
- Maximum Input Sound Level: 134 dB SPL, 1 kHz at 1% T.H.D.
- Dynamic Range (Typical): 105 dB, 1 kHz at Max SPL
- Signal-to-Noise Ratio: 65 dB, 1 kHz at 1 Pa
- Phantom Power Requirements: 11-52V DC, 2 mA typical
- Switch: The lever of elements can adjust the proper position
- Weight (Less Cable): 160 g
- Dimensions: 20.0 mm - height
85.0 mm – maximum body diameter - Cable: 7.6 m long (permanently attached to microphone), 4 mm diameter, 6 conductor, shielded cable; output end stripped and tinned for connection to electronic device
- Accessories Furnished: Soft protective pouch
|
Type of Transmitter UHF Frequency Agile
Input Connector Internal fitting for interchangeable capsules
Type of Microphone Electret Condenser Boundary Microphone
Polar Pattern Cardioid (Supplied)
Interchangeable Mic Heads Yes - R183B Omnidirectional, R184B Supercardioid and R185B Cardioid cartridges available
Frequency Response 50Hz to 17kHz
Battery Type/Approx. Life 9 Volt Alkaline - 7 hours based on alkaline battery
# Of Channels Over 100 channels between 692-862MHz, depending on locale
Mute Switch Programmable Touch-Sensitive Switch
Level Control Gain Adjustment Range: -6 to 34dBs
Antenna Type Internal
Display Microphone Status & Battery Life LEDs
Dimensions 3.625 x 1.8 x 5.17 (92 x 46 x 131mm) (WxHxD)
|
Condenser
Lightweight, sensitive diaphragm. Precisely and smoothly captures sound nuances. Powered by battery or phantom power supply.
Recommended Uses
Conference/Installed
Available Options
MX396C/DUAL Dual-Element 0-180 Degrees, Cardioid, back or bottom exit cable, mute output, LED input
MX396/TRI Dual-Element 90-0-90 mic, adjustable to 120-120-120 degrees, Cardioid, back or bottom exit cable, mute output, LED input
The Microflex® Multi-Element Boundary microphone delivers a unique and versatile tool for conference room installations.
Clean and simple in appearance, Multi-Element Boundary mics come in two or three element configurations, combining the coverage of multiple microphones into one small, compact package.
|
About the AKG Acoustics CBL 410 PCC
The AKG CBL 410 PCC Conference Microphone Set (Black) is a simple to use, plug and play desktop microphone for use with any PC or laptop. It improves audio quality incredibly when making a conference via VOIP. The microphone reproduces the voice with a clear and natural sound.
With its 3.5 mm stereo jack, it is a 100% plug and play device. No drivers are needed. Its ability to be cascaded makes the CBL 410 PCC the perfect tool for modern communication for both single person use in the office and/or multi-person use in a modern meeting room.
This microphone provides optimum intelligibility and audio quality for your meetings. The CBL 410 PCC is also an excellent choice for recording applications.
AKG Acoustics CBL 410 PCC Includes - AKG 3x CBL 410 PCC PC Boundary Layer Microphones
- GHAP1 USB Adapter
- AKG Warranty
AKG Acoustics CBL 410 PCC Features - Small and inconspicuous
- Exceptionally rugged
- Excellent sound quality
- High sensitivity
- Low self-noise
AKG Acoustics CBL 410 PCC Specifications Polar pattern | Omnidirectional | Microphone Type | Back electret condenser microphone | Frequency response | 50 Hz to 20 kHz | Impedance | 2000 ohms ±30% at 1000 Hz | Sensitivity | -42 dB ±3 dB (7.9 mV/Pa)Sensitivity: | Maximum current consumption | 0.5 mA | Supply voltage | 1.5 to 5 V DC | Cable length | 100cm (40“) | Connector | TRS mini jack |
|
C 547 BL
"Non-crush" case
Inconspicuous
Hypercardioid polar pattern
Easy to repaint
Hypercardioid, studio-quality boundary microphone with rugged, "non-crush" case and
switchable bass-cut filter for reducing footfall noise, ideal for tough on-stage assignments.
Other benefits include optimum acoustic properties, high directivity, and neutral sound.
Having the same frequency response, the C 547 BL can be combined with the CK 47 with
excellent results.
Primarily designed for use in places of worship, theaters, and conferencing, the C 547 BL
is also a good choice for miking kick drums and other instruments.
SPECIFICATIONS:
Polar pattern hypercardioid
Frequency range 30 to 18,000 Hz
Sensitivity 8.5 mV/Pa (-42 dBV)
Max. SPL 133 dB (for 1% THD)
Equivalent noise level 22 dB-A
Signal/noise ratio (A-weighted) 72 dB
Bass filter 12 dB/octave at 150 Hz
Impedance 400 ohms
Recommended load impedance >1000 ohms
Supply voltage 9 to 52 V phantom power to DIN 45596
Current consumption |
Reviews
There are no reviews yet.