Audio Technica U851A Cardioid condenser boundary microphone

Offering outstanding Audio-Technica sound for surface-mount applications, the U851A features a PivotPoint® rotating output connector, UniSteep® filter and UniGuard® RFI-shielding technology. This battery- or phantom-powered condenser microphone accepts interchangeable condenser elements - available for boundary microphones in cardioid, hypercardioid and omnidirectional polar patterns. Its heavy die-cast case and silicon foam bottom pads minimize coupling of surface vibration to the microphone. With superior off-axis rejection and maximum gain-before-feedback, this professional microphone sets audio-quality standards in challenging acoustic environments.

• Designed for surface-mount applications such as high-quality sound reinforcement, professional recording, television, conferencing and other demanding sound pickup situations
• PivotPoint® rotating output connector allows cable to exit from either the rear or the bottom of the microphone
• Superior off-axis rejection for maximum gain before feedback
• UniGuard® RFI-shielding technology offers outstanding rejection of radio frequency interference (RFI)
• UniSteep® filter provides a steep low-frequency attenuation to improve sound pickup without affecting voice quality
• Small-diameter UniPoint capsule near boundary eliminates phase distortion and delivers clear, high-output performance
• Heavy die-cast case and non-slip silicon foam bottom pads minimize coupling of surface vibration to the microphone
• Low-profile design with low-reflectance black finish for minimum visibility
• Operates on battery or phantom power

• Element: Fixed-charge back plate, permanently polarized condenser
• Polar Pattern: Half-cardioid (cardioid in hemisphere above mounting surface)
• Frequency Response: 30-20,000 Hz
• Low Frequency Roll Off: 80 Hz, 18 dB/octave
• Open Circuit Sensitivity: Phantom: -40 dB (10.0 mV) re 1V at 1 Pa Battery: -41 dB (8.9 mV) re 1V at 1 Pa
• Impedance: Phantom: 200 ohms Battery: 270 ohms
• Maximum Input Sound Level: Phantom: 133 dB SPL, 1 kHz at 1% T.H.D. Battery: 123 dB SPL, 1 kHz at 1% T.H.D.
• Dynamic Range: Phantom: 111 dB,1 kHz at Max SPL Battery: 101 dB, 1 kHz at Max SPL
• Signal to Noise Ratio: 72 dB, 1 kHz at 1 Pa
• Phantom Power Requiremens: 11-52V DC, 2 mA typical
• Battery Type: 1.5V AA/UM3
• Battery Current Life: 0.4 mA / 1200 hours typical (alkaline)
• Switch: Off, on-flat, on-roll-off
• Cable: 25.0' (7.6 m) long (permanently attached to microphone), 0.13" (3.2 mm) diameter, 2-conductor, shielded cable with TA3F-type connector
• Accessories: AT8531 power module; battery; soft protective pouch

The new Engineered Sound.

This low-profile omnidirectional condenser boundary microphone is designed for clear, highly intelligible sound reinforcement, professional recording and teleconferencing in table-, ceiling-, or panel-mount applications. The microphone is equipped with a self-contained power module with an XLRM-type output connector, eliminating the need for an external power module. The microphone offers unsurpassed immunity from radio frequency interference thanks to Audio-Technica's UniGuard® innovations. Protected by a rugged all-metal case with a two-layer steel mesh grille, the microphone has a 360º pickup angle, and is available in two colors: black (ES945) and white (ES945W).

• Designed for surface-mount applications such as high-quality sound reinforcement, professional recording and teleconferencing
• Low-profile element provides uniform omnidirectional polar pattern with 360º acceptance angle
• Mounts unobtrusively in table-tops, ceilings and wall panels
• Self-contained power module with XLRM-type output connector
• Rugged all-metal case with a two-layer steel mesh grille
• Isolators provide mechanical dampening of mounting-surface vibration
• Requires 11V to 52V DC phantom power
• UniGuard® RFI-shielding technology offers outstanding rejection of radio frequency interference (RFI)
• Available in two colors: black (ES945) and white (ES945W)
• RoHS compliant-free from all substances specified in the EU directive on hazardous substances

• Element: Fixed-charge back plate, permanently polarized condenser
• Polar Pattern: Omnidirectional
• Frequency Response: 40-18,000 Hz
• Open Circuit Sensitivity: -42 dB (7.9 mV) re 1V at 1 Pa
• Impedance: 200 ohms
• Maximum Input Sound Level: 142 dB SPL, 1 kHz at 1% T.H.D.
• Dynamic Range: 112 dB, 1 kHz at Max SPL
• Signal to Noise Ratio: 64 dB, 1 kHz at 1 Pa
• Phantom Power Requiremens: 11-52V DC, 2 mA typical
• Weight: 63 g (2.2 oz)
• Dimensions: 69.0 mm (2.72“) long, 28.0 mm (1.10“) diameter
• Output Connector: Integral 3-pin XLRM-type

Designed to deliver easy, flexible control in conference and boardroom installations, the versatile U891Rx cardioid condenser boundary microphone features a touch-sensitive on-off switch that can be set to three modes: press-on/press-off, press to talk, and press to mute. The phantom-powered microphone is equipped with a unique PivotPoint® rotating output connector and an LED status indicator. UniGuard® innovations offer unsurpassed immunity from radio frequency interference; interchangeable elements are available in cardioid, hypercardioid and omnidirectional polar patterns; an 80 Hz low-cut UniSteep® filter reduces pickup of low-frequency ambient noise. The microphone's heavy die-cast case and silicon foam bottom pads minimize coupling of surface vibration to the microphone. The unit's self-contained electronics eliminate the need for an external power module.

• Designed for surface-mount applications such as high-quality sound reinforcement, professional recording, television, conferencing and other demanding sound pickup situations
• Ultra-quiet electronic switch can be set to any of three operating modes: "touch-on/ touch-off," "touch-to-talk" and "touch-to-mute“
• PivotPoint® rotating output connector allows cable to exit from either the rear or the bottom of the microphone
• Superior off-axis rejection for maximum gain before feedback
• UniGuard® RFI-shielding technology offers outstanding rejection of radio frequency interference (RFI)
• Small-diameter UniPoint® capsule near boundary eliminates phase distortion and delivers clear, high-output performance
• Heavy die-cast case and non-slip silicon foam bottom pads minimize coupling of surface vibration to the microphone
• Low-profile design with low-reflectance finish for minimum visibility
• Available in two colors: black (U891Rx) and white (U891RWx)

• Element: Fixed-charge back plate, permanently polarized condenser
• Polar Pattern: Half-cardioid (cardioid in hemisphere above mounting surface)
• Frequency Response: 30-20,000 Hz
• Low Frequency Roll Off: 80 Hz, 18 dB/octave
• Open Circuit Sensitivity: 34 dB (19.9 mV) re 1V at 1 Pa
• Impedance: 200 ohms
• Maximum Input Sound Level: 130 dB SPL, 1 kHz at 1% T.H.D.
• Dynamic Range: 104 dB, 1 kHz at Max SPL
• Signal to Noise Ratio: 68 dB, 1 kHz at 1 Pa
• Phantom Power Requirements: 11-52V DC, 4 mA typical
• Weight: 264 g
• Dimensions: 108.0 mm long, 84.0 mm maximum width, 23.0 mm height
• Output Connector: TB3M-type
• Cable: 7.6 m long, 3.2 mm diameter, 2-conductor, shielded cable with TA3F and XLRM-type connectors

C 547 BL 

"Non-crush" case
Inconspicuous
Hypercardioid polar pattern
Easy to repaint
 
Hypercardioid, studio-quality boundary microphone with rugged, "non-crush" case and
switchable bass-cut filter for reducing footfall noise, ideal for tough on-stage assignments.
Other benefits include optimum acoustic properties, high directivity, and neutral sound.
Having the same frequency response, the C 547 BL can be combined with the CK 47 with
excellent results.
Primarily designed for use in places of worship, theaters, and conferencing, the C 547 BL
is also a good choice for miking kick drums and other instruments.

SPECIFICATIONS:
Polar pattern hypercardioid
Frequency range 30 to 18,000 Hz
Sensitivity 8.5 mV/Pa (-42 dBV)
Max. SPL 133 dB (for 1% THD)
Equivalent noise level 22 dB-A
Signal/noise ratio (A-weighted) 72 dB
Bass filter 12 dB/octave at 150 Hz
Impedance 400 ohms
Recommended load impedance >1000 ohms
Supply voltage 9 to 52 V phantom power to DIN 45596
Current consumption

    Designed for Broadcast, House of Worship, Pro Music, and other applications.
    Half-cardioid polar pattern
    Boundary layer
    Ultra-thin profile (16 mm) housing
    Rubber non-slip bottom pad and strong steel screen
    Integrated pop filter

Case Material    Die cast zinc
Connector Type    3-pin XLR
Element    Back Electret Condenser
Finish    Non-reflecting Black
Finish    White
Impedance, Low-Z balanced    200 Ω
Mic Type    Boundary
Open Circuit Voltage    25 mV/Pascal
Polar Pattern    Cardioid
Wired/Wireless    Wired
Height    16 mm (0.63“)
Width    94 mm (3.7“)
Depth    123 mm (4.84“)
Weight Net    12.63 oz (358 g)