| Content |
- 2 analog inputs and 6 analog outputs for maximum flexibility
- High-end 96 kHz converters for ultimate signal integrity and wide dynamic range (120 dB)
- Precise Dynamic EQs for level-dependent equalization and extremely musical Parametric EQs, selectable for all inputs and outputs
- Several types of EQs (LP/BP/HP) for each input and output
- “Zero“-attack Limiters on all output channels for optimal speaker protection
- Four different mono and stereo output operating modes
- Individual crossover filter types (Butterworth, Bessel and Linkwitz-Riley) with selectable roll-off characteristics from 6 to 48 dB/octave
- Adjustable Delays for all inputs and outputs—allow manual or automatic correction for room temperature, phase and arrival time differences
- 60 user-defined internal presets storable
- Servo-balanced, gold-plated XLR connectors for all inputs and outputs
- Internal switch-mode power supply for maximum flexibility (100 - 240 V~), noise-free audio, superior transient response plus low power consumption for energy saving
- High-quality components and exceptionally rugged construction ensure long life
- Conceived and designed by BEHRINGER Germany
|
Lab Gruppen NLB 60E
The NomadLink network provides remote monitoring, control and power sequencing functions for multiple C Series or FP+ amplifiers. Indeed up to 16 NLB 60E network bridges, each monitoring up to 60 amplifiers may be accommodated in one system. Easy setup, redundancy, and minimum maintenance were bywords when developing this network format.
NomadLink is a closed-loop, daisy-chained network topology with the NLB 60E providing the bridge to the familiar world of Ethernet/LAN. NomadLink reduces installation time and cost significantly, includes redundancy during operation by design and simplifies the location of faults or system abuse.
NomadLink together with the associated DeviceControl software allows the subnets’ architecture to be automatically uploaded even without individual IP addresses in the amplifiers. All in all, it is the fastest and easiest monitoring and control network on the market today.
Specifications:
Network Connectors:
* Nomadlink Out: EtherCon housed RJ45
* Nomadlink In: EtherCon housed RJ45
* Ethernet rear-panel: EtherCon housed RJ45
* Ethernet front-panel: Standard RJ45
General Purpose Inputs (GPI):
* One Voltage sensing input: Two pole Phoenix
* Two contact closure inptus: Two pole Phoenix
Front Panel Indicators:
* Front operation locked: Yellow LED
* Fault warning: Red LED
* Amplifier subnet muted: Red LED
* NomadLink network connected/activity: Blue LED
* Ethernet connected: Orange LED
* Ethernet Activity: Yellow LED
2 x 16 Character display: White text, Blue background
Navigation and Adjust keys: Yes, x 6
Subnet Power on/off keys: Yes, x 2
Power: 100 to 240 VAC, 50 to 60 Hz (auto-select)
Power consumption:
Finish: Anodized aluminum front, Plated and painted steel chassis
Approvals: CE, CSA
Dimensions (W x H x D): 19" x 1.73" x 8.2" (483 x 44 x 208 mm), 1 RU
Weight: 5 lbs. (2.25 kg)
| Overview
More sound to your amps and speakers
The secret to making speakers sound great lies with the crossover you use. With the dbx® 223xs Crossover you\'ll get great performance, ultra low-noise, rugged reliability and four decades of dbx knowledge and expertise in building the world\'s finest processors. The 223xs uses precision filters to separate the audio signal and direct the correct frequencies to your loudspeaker drivers. By directing only the specific frequency bands to each speaker driver the 223xs leaves your amplifiers free to use their full power on the usable signal eliminating distortion and giving your PA system a cleaner and better sound.
The dbx 223xs is a dual channel crossover with all the features you would expect from a professional product. It features Linkwitz-Riley 24dB per octave filters, independent output gain controls for level matching, output phase inversion, 40 Hz low cut filter, and optional mono summing of the low frequency (subwoofer) output. Everything in the design exudes great precision from the solid "click" controls to the high quality XLR inputs and outputs
Features
- XLR balanced ins and outs
- Mode switch for stereo 2-way or mono 3-way operation
- Low frequency summed (subwoofer) output
- x10 range switch on both channels
- 40Hz high pass (low cut) filter both channels
- Phase reverse switch on all outputs
- Individual level controls on all outputs
- 24dB per octave Linkwitz-Riley filters (the professional standard)
- Stereo/Mono status LEDs indicate the selected mode
- dbx® 2 year parts and labor as standard
- CSA NRTL/C approved
- CE compliant
Specifications
| Input Connectors |
XLR (pin 2 hot) |
| Input Type |
Electronically balanced/unbalanced, RF filtered |
| Input Impedance |
Balanced >50k ohm, unbalanced >25k ohm |
| Max Input |
>+22dBu balanced or unbalanced |
| CMRR |
>40dB, typically >55dB at 1kHz |
| Output Connectors |
XLR |
| Output Type |
Impedance-balanaced/unbalanced, RF filtered |
| Output Impedance |
Balanced 200 ohm, unbalanced 100 ohm |
| Max Output |
>+21dBu balanced/unbalanced into 2k ohms or greater |
| Bandwidth |
20Hz to 20kHz, +/-0.5dB |
| Frequency Response |
90 kHz, +0/-3 dB |
| Signal to Noise Ratio |
Ref: +4 dBu, 22 kHz measurement bandwidth |
| Signal-to-Noise (Stereo Mode) |
>94dB (Low Output), >91dB (High Output) |
| Signal-to-Noise (Mono Mode) |
>94dB (Low Output), >93dB (Mid Output), >91dB (High Output) |
| Dynamic Range |
> 106 dB, unweighted, any output |
| THD+Noise |
< 0.004% at +4 dBu, 1 kHz; < 0.04% at +20 dBu, 1 kHz |
| Interchannel Crosstalk |
< -80 dB, 20 Hz to 20 kHz |
| Crossover Frequencies (Stereo Mode) |
Low/High: 45 to 960 Hz or 450 Hz to 9.6 kHz (x10 setting) |
| Crossover Frequencies (Mono Mode) |
Low/Mid: 45 to 960 Hz or 450 Hz to 9.6 kHz (x10 setting); Mid/High: 45 to 960 Hz or 450 Hz to 9.6 kHz (x10 setting) |
| Crossover Filter Type |
Linkwitz-Riley, 24 dB/octave, state-variable |
| Low cut Switch |
Activates 40 Hz Butterworth, 12 dB/octave high-pass filter, one switch per channel. |
| Phase Invert Switch |
Inverts the phase at the output, one switch per output. |
| x1 / x10 Switch |
Multiplies the low-high(mono: low/mid and high/mid) crossover frequency range of the front-panel markings by a factor of 1 or 10, one switch per channel. |
| Mode Switch |
Selects stereo/mono and 2/3-way operation |
| LF Sum Switch |
Selects normal (stereo) or mono-summed low frequency operation and disables Ch 2ʼs low output phase invert LED to indicate that this output is not operational in the LF sum mode. |
| Indicators |
Stereo Operation (Green); Mono Operation (Yellow); Low Cut (Red-per channel); x10 (Green-per channel); Phase Invert (Red-per output) |
| Operating Voltage |
100 VAC 50/60 Hz; 120 VAC 60 Hz 230 VAC50 HZ |
| Operating Temperature |
32°F to 113°F (0°C to 45°C) |
| Power Consumption |
15W |
| Power Connector |
IEC receptacle |
| Dimensions |
1.75" H X 19" W X 6.9" D (4.4cm x 48.3cm x 17.5cm) |
| Unit Weight |
3.7 lbs. (1.7 kg) |
| Shipping Weight |
5.4 lbs. (2.5 kg) |
| Behringer DCX2496 Overview
The DCX2496 ULTRADRIVE PRO from Behringer is a digital loudspeaker management system, that provides excellent audio quality, along with a comprehensive feature list. It allows for precise set-up of multiple loudspeaker arrays, suitable for live sound, fixed installations that require control of loudspeaker systems, and other contractor-installed applications.
Each of the three-inputs and six-outputs have fixed processing blocks, including gain, delay, EQ and dynamic EQ on the input channels, and gain, crossover, EQs, limiter and delays on the output side. One of the inputs can accept a stereo AES/EBU digital signal. An integrated sample rate converter assists in accepting various sample rates. Additionally, an internal input-sum signal is easily set-up.
Four different mono and stereo output operating modes are available, all with individual crossover filter types with selectable roll-off characteristics. Input and output delays allow for time adjusting signals to compensate for ambient temperature changes or for adjusting arrival time differences for individual speaker clusters. EQs can be used for both musical enhancement or for level-dependent equalization. Brick-wall limiters guarantee speaker protection.
Remote control of one or several units can be accomplished utilizing downloadable software for a Windows based computer. Set-ups can be saved to the software, or to an optional PCMCIA card for the ultimate in portability. Servo-balanced, gold-plated XLR connectors for all inputs and outputs guarantee excellent connectivity.
- Three-input, six-output loudspeaker management system
- Four different mono- and stereo-output operating modes
- Individual crossover filter types including Butterworth, Bessel and Linkwitz-Riley, with selectable roll-off characteristics from 6dB to 48dB per octave
- Choice of high-, band- and low-pass filters for each input and output
- Dynamic EQ for level-dependent equalization and parametric EQ selectable for each channel
- “Zero" attack limiters on all output channels for optimal signal protection
- Automatic or manual-adjustable delays for all inputs and outputs allow for adjustment due to room temperature, phase and arrival time differences
- Link option via RS-485 network interface allows for linking multiple units for larger installation requirements
- Downloadable software enables single- or multiple-unit remote control utilizing a Windows based computer
- Sixty user-defined internal presets can bestored via software or on a PCMCIA card
- Internal universal power supply allows the unit to operate virtually anywhere
| Frequency Response |
10Hz to 35kHz, -1dB |
| Dynamic Range |
109dB |
| Input Connections |
3 x XLR |
| Output Connections |
6 x XLR |
| Input Impedance |
20kΩ @ 1kHz |
| Output Impedance |
160Ω @ 1kHz |
| Maximum Input Level |
+22dBu |
| Maximum Output Level |
+22dBu |
| Sample Rate |
32kHz to 96kHz |
| RTA Mic Phantom Voltage |
+15V |
| Crosstalk (Main Outputs) |
-100dB @ 10dBu In |
| THD & Noise |
0.007% @ 0dBu In |
| Dimensions |
19" x 8.5 x 1.75" (483 x 217 x 45mm) |
| Weight |
6.6 lbs (3 kg) |
|
The LD DPA260 is a 6-Channel 19" Speaker Processor for our VA-4, VA-8 and UNO-Array with plenty of useful setups for each system
- Type: DSP Controller for Line Array VA-4, VA-8 and UNO
- Model Name: DPA-260
- Description: 6-Channel 19" speaker processor, 32bit DSP, 24bit AD/DA (48 kHz) converter
- Inputs: 2 Channels Analog/Digital, L + R, Noise Gate, the inputs and outputs are freely assignable, that means you can assign any input to any output and vice versa
- Input EQ: 5 Band PEQ, Low Shelf and High Shelf Types available
- Crossover Range: 20 Hz - 20 kHz
- Outputs: 6 Channels, High/Low Pass Filter, Filtertype and dB available, 7 Band PEQ, Low Shelf and High Shelf Types available, Limiter with Threshold, Attack and Release Parameters
- Delay: Time or Meter available, Max. Delay up to 848 ms
- Phase Invert Function: USB Port, Full programmable Software included with 24 Memory Capacity for Presets
- Display: 2 × 16 character LCD with backlight
- Switch mode power supply: 90 V - 250 V
- Dimensions: 19" / 1U
| Crossover 2-Way stereo or 3-way mono mode Additional subwoofer output Linkwitz-Riley filter with 24 dB / octave Sub-woofer frequency range separately adjustable Individual output gain controls and output mute switch for all bands 2 Balanced XLR inputs with gold-plated contacts 5 Balanced XLR outputs with gold-plated contacts Switchable 25 Hz low-cut filter to protect loudspeakers from infrasound Easy-to-read status LEDs Built-in power supply 100-240V, 50-60 Hz Dimensions (H x W x D): 44 x 483 x 147 mm Weight: 1.6 kg |
Reviews
There are no reviews yet.