Content |
The original Soundweb 9010 Programmable Controller set new standards in control interfacing to DSP systems, and has yet to be bettered as a simple yet powerful interface.
The Soundweb London equivalent, the BLU-10, builds on that power and reputation by adding touch-screen control to make a more attractive and potentially cost-saving control solution. It is possible that a BLU-10 could replace a more expensive proprietary touch screen solution where simpler control interfacing is required.
As with the Soundweb 9010, up to 100 control ʽpagesʼ of virtually any Soundweb London DSP parameter can be constructed, with the ability to create ʽfoldersʼ for nested pages. Access to specific pages or folders can be restricted with the used of password protection, so that only engineers or key employees can adjust critical system parameters.
Each page can hold up to eight different functions and with navigation being carried out entirely by a page list, all of these functions can be assigned to real parameters rather than functioning as page transitions.
Programming the BLU-10
Soundweb users will be familiar with the simple drag-and-drop programming interface, and the BLU-10 interface is very similar. Once the menu pages have been created, operation of the pages can be tested using the special simulation mode, which emulates how the controller will work when in use. This allows menu structures to be checked before the system goes live.
The BLU-10 connects into a Soundweb London network via its Ethernet port, either directly into the rear of a rackmount device such as the BLU-16 with a Cat 5 crossover cable or with a standard Cat 5 cable into an Ethernet switch. The unit is powered either using the terminals on the rear, accepting a range of 12V - 48V DC or with IEEE802.3af Power Over Ethernet (POE).
Mechanical Installation
The BLU-10 mounts in a standard US 3-gang wallbox (available from BSS Audio) using the screws provided with the unit. |
The MULTIGATE PRO XR4400 provides four frequency-selective expanders/noise gates in a single rack space. Each section comprises an ultra-fast gate, a program dependent expander, a filter section and precision meters indicating both threshold point and gain reduction.
The included side chain parametric filters allow the user to fine-tune control signals so that the gate reacts only when required. The Interactive Attack Control (IAC) circuit analyzes the program material to calculate the attack time of the gate. Separate hold and release controls offer additional flexibility. The XR4400 has a switchable operating mode for the gate and expander. With the MODE function off, the unit works in gate mode using an extremely fast attack time, thus preserving the transient details of the program material. In expander mode, the device analyzes the shape and dynamic contents of the input signal to calculate the control time parameters. The result is that vocals, instruments and complex mix signals can be cleaned up without audible clicks or other detrimental effects.
A couple function on the XR4400 provides a great deal of flexibility to link the expander/gate sections in a master/slave configuration.
Quadruple expander/gateHigh-precision parametric filter for frequency selective operationFully adjustable Ratio control in Expander modeFully adjustable Attenuation control in Gate modeIndependent Hold/Release controls for any envelope shapingFlexLink system for flexible Master/Slave configurationsExtremely low-noise operational amplifiers and high-grade VCA\'sFilter Monitor facility for monitoring the filter sectionHigh-quality detent potentiometers and backlit switchesServo-balanced gold-plated XLR and 1/4" TRS inputs and outputs8-digit LED meters for input level, output level and gain reduction monitoring
Function |
Four channel expander/gate |
Number of Channels |
4 |
Inputs |
4 x XLR, 4 x TRS 1/4" phone |
Output |
4 x XLR, 4 x TRS 1/4" phone |
Maximum Input Level |
+21dBu |
Compression Threshold |
Not applicable |
Compression Ratio |
Not applicable |
Attack Time |
Not applicable |
Release Time |
Not applicable |
Gate Threshold |
0 to -80dB |
Gate Rate |
Attack: Program dependant Hold: 0 to 4 sec, variable Release: 50ms to 4 sec, variable |
Maximum Output Level |
+21dBu |
Make-up Gain |
Not specified by manufacturer |
Frequency Response |
18HZ to 30kHz |
Dynamic Range |
Not specified by manufacturer |
Noise |
>95dBu, unweighted, 22Hz to 22kHz |
Dimensions |
1U rack mount, 8 1/2" deep |
Specialties |
Unit will operate at either +4dB or -10 dB |
|
SPECIFICATIONS
Input: Coaxial RCA digital audio, PCM stereo or Dolby Digital
Output: Left and Right RCA analog
Frequency Response: 20Hz to 20kHz, (+/- 0.5 dB)
THD: 0.025%
Power Requirement: Input: 100V~240V AC, Output: 5V DC (use Xantech supplied power supply only)
Dimensions (W x H x D):
Unit: 4-3/4” x 1” x 1-15/16” (119 x 25 x 48 mm)
Single pack carton: 7-1/4” x 3-1/2” x 6-1/2” (185 x 85 x 165 mm)
Weight:
Unit: 0.25 lbs (0.12 kg)
Single pack carton: 0.85 lbs (0.40 kg) |
INPUT: 4 balanced +4dBu/50kΩ on female XLR connectors; 4 unbalanced 1Vpp/50kΩ on RCA connectors.
OUTPUT: 4 unbalanced 1Vpp/49Ω on RCA connectors; 4 balanced +4dBu/49Ω on male XLR connectors.
MAX. OUTPUT: 18Vpp.
BANDWIDTH (-3dB): 30kHz.
S/N RATIO: Better than 89dB.
THD: Less than 0.02%.
POWER SOURCE: 115-230V AC, 50/60Hz, 3.7VA.
DIMENSIONS: 19" x 7" x 1U W, D, H, rack mountable.
WEIGHT: 2.4kg (5.3lbs) approx.
ACCESSORIES: Power cord. |
An elegant slim-line device contains all the functions required by a system for distributing different musical programmes in homes for multi-room sound systems and commercial premises.
Three different musical programmes and one for paging can be transmitted in five mono zones, or alternatively four zones, one of which is in stereo. It is also possible to extend the number of zones to ten using a simple connector to interlink two systems. The system has five amplified 20 W / 4 ohm outputs. For each of the five zones, a direct auxiliary input is available for connecting sources such as CD players or mixers to be used exclusively for one zone/room.
The back-lit display and function keys make it possible to access all the menus for configuring and adjusting the system: Volume, Tone, Loudness, Output settings, VOX.
Features |
---|
3 Music Source Inputs individually selectable to each output | One Input Source with Override facility (Jukebox or Auto Announcer) | 5 zoned outputs (Mono) or 1 Stereo and 3 Mono Output Zones | Can be expanded interlink of two or more MS520 units | Inbuilt 20W into 4 Ohms 5 channel Amplifiers (1 Stereo – 3 Mono Option) | Direct Inputs and Outputs on each zone | Paging or Alarm Input Override System | Full Digital Matrix control of functions to all 5 zones | Up to 10 remote control panels RC 62 can be connected to each MS 520 |
AMPLIFIER SPECIFICATIONS |
---|
Power output: | 5 x 20 | Watt rms | Frequency Response (Music): | 30 ÷ 45 | Hz ÷ kHz | Frequency Response (Direct): | 30 ÷ 45 | Hz ÷ kHz | Frequency Response (Paging): | 200 ÷ 18 | Hz ÷ kHz | Distortion: | 0.5 | % | Signal / noise ratio (Music): | -78 | dB | Signal / noise ratio (Direct): | -78 | dB | Signal / noise ratio (Paging): | -60 | dB |
INPUT SECTION |
---|
Input sensitivity (Music): | -16 | dBu | Input sensitivity (Direct): | -16 | dBu | Input sensitivity (Paging - Line): | - 43 ÷ -27 | dBu | Input sensitivity (Paging - Mic): | - 58 ÷ -41 | dBu | Bass Tone: | (100 kHz) ± 8 | dB | Treble Tone: | (12.5 kHz) ± 8 | dB |
OUTPUT SECTION |
---|
Out level: | -6 / -10 | dB | Protections: | Short ciurcuit, thermal, AC / DC fuses | | Power supply: | 16 | V dc |
POWER REQUIREMENT |
---|
Operating voltage: | 220÷240 / 110÷120 V ~ 50 / 60 Hz | V ~ Hz | Power (consumption): | 370 | W | Max. Available power: | 100 | W |
PHISICAL SPECIFICATION |
---|
Width: | 438 / 17.24 | mm/inch | Height: | 44 / 1.73 | mm/inch | Depth: | 253 / 9.96 | mm/inch | Net Weight: | 3.66 / 8.06 | Kg/Lbs |
SHIPPING INFORMATION |
---|
Package height: | 75 / 2.95 | mm/inch | Package width: | 520 / 20.47 | mm/inch | Package depth: | 280 / 11.02 | mm/inch | Shipping Weight: | 4.18 / 9.21 | Kg/Lbs |
|
Product Features: 16-channel digital stereo mixer to create your personal monitor mix Ultra-intuitive \"analog\" operation with total recall and 16 presets for custom mixes State-of-the-art 24-bit D/A converters for premium audio quality 16 Channel Select buttons with dual LEDs for perfect overview Level and Pan/Spread control per channel with LED meter 3-band EQ per channel with mid-band frequency control Solo and Mute functions per channel Global Level and EQ controls plus Panic Mute function High power and \"drummer proof\" headphones output Fully adjustable limiter protects your ears and headphones Additional mono/stereo line output to connect your powered monitor MIDI IN port for real-time remote control of all channels by external MIDI device such as BEHRINGER BCF2000, BCR2000, etc. Standard CAT5e connection delivers power and 16 signals to each Personal Mixers ULTRANET connector to daisy-chain up to forty-eight P16-M mixers for large systems (in conjunction with P16-D) Ultra-low system latency of less than 1 millisecond Powered via external power supply (included) or P16-I / P16-D Mounts easily on a mic stand with the P16-MB mic stand mount (not included) Extremely rugged construction ensures long life even under the most demanding conditions Conceived and designed by BEHRINGER Germany
User\'s Manual |
Reviews
There are no reviews yet.