| Content |
cosMik Lav is a professional omnidirectional lavalier microphone, providing high quality audio recording for mobile devices such as iPhone, iPad and various Android devices. The input sensitivitiy and level is optimized for these mobile devices, providing perfect signal levels in order to significantly improve the audio quality of your recordings.
cosMik Lav is very easy to use and works with most audio and video recording apps, providing you with a hands-free solution to capture natural and clear sound of speeches, lectures, interviews, dictations and much more. The polar pattern of cosMik Lav is omnidirectional, which means that you will get a perfect response even if the speaker is moving while recording.
The special connector makes it possible to connect your headset at the same time - providing you with a quick and easy solution to playback and listen to your recordings without unplugging the microphone first.
The included clip can be attached to your shirt or lapel and the foam pop shield softens the voice and shields from wind noise.
There is also a pouch included, for convenient storage and transport.
Features:
compact lavalier microphone
omni-directional condenser capsule
40Hz - 20kHz frequency range
-39dB sensitivity
3k Ohm output impedance
115dB max. SPL (1% THD, @ 1kHz)
65dB signal/noise ratio (A-weighted)
TRRS connector for smartphones
works with iPhone, iPad, most Android phones
works with any audio app that can use headset input
output connector to connect earphones simultaneously
foam pop shield to reduce wind noise
mic clip to connect to shirt / lapel
small cloth pouch included for transport and storage
cable length: 1.2m
weight: 20g (microphone with clip and connector)
Τype:
| Lavalier | | Colour: | Black | | Connector: | Jack 4P 3.5 |
|
All models include foam windscreens, swiveling lapel clip, dual tie clip, magnet mount, and mini mount
Subminiature size (5.8 mm diameter x 11 mm height)
Electret condenser cartridge
Omnidirectional pattern
One termination: 4-pin mini connector (fits directly into Shure wireless transmitters)
Two sensitivities available:
--Standard: -40 dBV/Pa (for speech applications)
--Reduced: -50 dBV/Pa (10 dB more headroom for theater applications)
Interchangeable equalization caps for optimal clarity and response:
--Silver mesh cap provides a 4 dB boost in the 8-18 kHz range - typically used in applications that require a microphone to be head-mounted
--Gold mesh cap provides a 10 dB boost centered at 12 kHz - typically used in applications that require a chest-worn microphone
Black, beige, and white models are available
All models include magnet mount, lapel clip, dual tie clip, pin mount, and two foam windscreens
Frequency response: 20-20,000 Hz
|
Shure cable with base WL180N fits with R183/184/185 | Subminiature lavalier design; ideal size for theater, television, broadcasting, video, film, and sound reinforcement
Small, inconspicuous mounting hardware
Full, clear sound comparable to larger microphones
Smooth extended frequency response with presence rise specially tailored for chest-worn microphone operation
Controlled low-frequency rolloff reduces low-frequency clothing and room noise
Low distortion, wide dynamic range
Uniform omnidirectional polar pattern
Preamplifier assembly (SM93) can be pocketed, strapped to the body, or clipped to belt or waistband
Wide-range phantom powering (SM93) accepts all commonly used voltages
Type
Condenser (electret bias)
Frequency Response
50 to 20,000 Hz
Response Curve Image Small SM93 WL93 View Larger
Polar Pattern
Omnidirectional, uniform with frequency
Output Impedance
3000 ohms
Output Level (1 Pascal = 94 dB SPL)
Open Circuit Voltage: -38 dBV/Pa (13 mV)
Output Clipping Level (at 1,000 Hz)
0.25 V at 120 dB
Total Harmonic Distortion
Less than 1% at 120 dB
Maximum SPL
120 dB
Dynamic Range (maximum SPL to A-weighted noise level)
102 dB
Output Noise (equivalent SPL)
18 dB typical, A-weighted
Signal-to-Noise Ratio
76 dB at 94 dB SPL (IEC 651)
Polarity
Positive pressure on microphone diaphragm produces positive voltage on pins 3 and 4 with respect to pin 1 (ground)*
*Produces positive voltage at pin 2 of Shure wireless receiver three-pin connector
Recommended Operating Voltage
2 to 10 V; 5 V nominal (pin 2 to pins 3 and 4)
Current Drain
40 microA typical
Environmental Conditions
Operating Temperatures: -18 to 57 degrees C (0 to 135 degrees F)
Storage Temperatures: -29 to 74 degrees C (-20 to 165 degrees F)
Cable
Black 1.27 m (4.17 ft), attached, two-conductor, shielded, terminated by miniature connector type TA4F (WL93T: Tan 1.27 m [4.17 ft])
Case
Microphone: Black ABS thermoplastic case with stainless-steel-mesh grille
Net Weight
Microphone: 16 g (0.57 oz) |
Shure SLX14 Instrument Wireless System Features:
SLX4 Wireless Receiver:
Automatic Frequency Selection
Automatic Transmitter Setup
960 Selectable frequencies across 24MHz bandwidth
Detachable 1/4 wave antennas
Microprocessor-controlled diversity
RF presence LED
5-segment audio meter
Multi-function, backlit LCD
Low battery indicator
Frequency and power lockout
Rugged metal chassis
Volume control on rear of unit
1/2 rack design
Furnished rack hardware
Non-slip bumpers for use out of rack
XLR and 1/4" outputs
SLX1 Bodypack Transmitter
Automatic Transmitter Setup
Backlit LCD with timeout feature
Frequency and power lockout
3-segment battery fuel gauge
2 AA batteries (included) provide 8 hours of continuous use
518 - 782 MHz operating range
Shure SLX14 Instrument Wireless System Specifications:
SLX4 Wireless Receiver:
Audio Output Level (ref. ± 38kHz deviation with 1kHz tone): XLR connector (into 600 Ohm load): —13dBV; 1/4" connector (into 3000 Ohm load): —2dBV
Output Impedance: XLR connector: 200 Ohms; 1/4" connector: 1kohms
XLR output: Impedance balanced; Pin 1: Ground; Pin 2: (+); Pin 3: (-)
Sensitivity: —105 dBm for 12 dB SINAD, typical
Image Rejection: >70 dB, typical
Power Requirements: 12—18 Vdc at 150 mA, supplied by external power supply
Operating Range Under Typical Conditions: 300 ft. (100m)
Note: Actual range depends on RF signal absorption, reflection, and interference
Audio Frequency Response (+/— 2 dB): Minimum: 45 Hz: Maximum: 15 kHz
Note: Overall system frequency depends on microphone element.
Total Harmonic Distortion (ref. +/— 38 kHz deviation, 1 kHz tone): 0.5%, typical
Dynamic Range: >100 dB A-weighted
Operating Temperature Range: —18 degree C (0 degree F) to +50 degree C (+122 degree F)
Note: battery characteristics may limit this range
Dimensions (H x W x D): 1.65 x 7.76 x 5.28 in., (42 x 197 x 134 mm)
Weight: 1 lb. 13 oz. (816 g )
Housing: Galvanized steel
Transmitter Audio Polarity: Positive pressure on microphone diaphragm (or positive voltage applied to tip of WA302 phone plug) produces positive voltage on pin 2 (with
respect to pin 3 of low impedance output) and the tip of the high impedance 1/4-inch output.
Logic Connections: Pin 1: Logic output, Transmitter Mute Status. Mute=low (0 V). Sinks up to 100 mA. Absolute maximum -0.7 to 5.5V DC; Pin 2: Logic ground; Pin 3: Logic output, Battery Status. Good=low (0 V). Sinks up to 100 mA; Absolute maximum -0.7 to 5.5V DC
SLX1 Bodypack Transmitter
Audio Input Level: -10 dBV maximum at mic gain position, +10 dBV maximum at 0 dB gain position, +20 dBV maximum at -10 dB gain position
Gain Adjustment Range: 30dB
Input Impedance: 1 Mohms
RF Transmitter Output: 30 mW maximum (dependent on applicable country regulations
Dimensions (H x W x D): 4.25 x 2.50 x 0.75 in. (108 x 64 x 19 mmD)
Weight: 81 grams (3 oz.) without batteries
Housing: Molded ABS case
Power Requirements: 2 "AA" size alkaline or rechargeable batteries
Battery Life: >8 hours (alkaline)
|
Transducer Electret condenser
Polar Pattern Cardioid
Frequency Response 20 to 20,000Hz
Output Impedance 165.5 Ω
Sensitivity -39.0 dBV/Pa (11.0 mV)
Max Input Sound Level (SPL) 1000 Ω load: 129.5 dB SPL; 2500 Ω load: 134.5 dB SPL
Signal-to-Noise Ratio 57.0 dB
Dynamic Range @1kHz
1000 Ω: 92.5 dB SPL; 2500 Ω: 97.5 dB SPL
Self Noise 37.0 dB
(equivalent SPL, A-weighted, typical)
Clipping Level 1000 Ω load: 1.0 dBv; 2500 Ω load: -4.5 dBv
Operating Temperature Operating: 0 to 135°F (-18 to 57°C)
Storage: -20 to 165°F (-29 to 74°C)
Polarity XLR: Positive pressure on diaphragm produces positive voltage on pin 2 with respect to pin 3
Power Requirements 11-52VDC phantom power (IEC-61938),
Dimensions (LxDiameter) Length: 5' (1.52m)
Diameter: 0.23" (5.8mm)
Weight 4.3 oz (121 g)
|
Reviews
There are no reviews yet.