| Content |
The X1 A: It could be your first mic, but it's one you'll want to keep forever.
There's a new entry point to sE's acclaimed X1 Series, and it's breaking the performance barrier (again) for every mic in its class.
When it was introduced in 2011, the X1 brought a new level of quality to its price point, competing easily with microphones costing several times as much. But that didn't stop sE from trying to outdo themselves again.
With a newly-developed condenser capsule and an exterior based on the rugged metal chassis of the X1, the X1 A offers first-class sound & specifications at an even better "home studio" cost, featuring an extremely natural frequency response, massive SPL-handling capabilities (150dB!), switchable attenuation and low-cut filters, and a perfectly balanced sensitivity level - so it's at home on absolutely any source.
In the box:
- X1 A microphone
- swivel mic clip
- mic stand thread adapter
| The e 945 is a fully professional super-cardioid vocal microphone which cuts
through the mix and offers a smooth, natural sound. Its warm tonal response
is matched with rugged construction and excellent feedback rejection.
Features
Rugged metal body
Advanced shock-mount design
Consistent on-/off-axis response
Hum compensating coil
Made in Germany
Delivery includes a pouch and a microphone clamp
Delivery Includes
1 e 945
MZQ 800 microphone clamp
Pouch
Technical Data
Pick-up pattern Super-cardioid
Frequency response (microphone) 40.....18000Hz
Sensitivity in free field, no load (1kHz)
2,0mV/Pa bei 1 kHz = -54dB (0 dB = 1V/Pa) = -74 dB (0 dB = 1V/ubar)
Nominal impedance 350 Ohm
Min. terminating impedance 1000 Ohm
Dimensions 47 x 186 mm
Weight 330 g |
MC10M is a multi capsule microphone set including a cardioid electret condenser microphone
(MC10) with the replaceable super cardioid capsule, shock mount adaptor, and wind screen.
MC10M can be used in wide applications, from studio & home recording to field sound aquisition.
FEATURES:
Replaceable 2 types of polar pattern capsule, cardioid/super cardioid as standard
Wide frequency response range
High sensitivity
Low distortion
High input withstand S.P.L.
Rugged brass case
Light weight
Shock mount adaptors, stereo mounting blacket & wind screen as standard
Dedicated carrying case as standard
SPECIFICATIONS:
Type :Back Electret
Condenser Microphone
Polar Pattern :Cardioid/Super Cardioid
Frequency Response :40Hz to 20kHz +/-10dB
Sensitivity :-40dBV/pa (10mv/pa)
Rated Impedance :200W
Equivalent Noise Level
:22dB (A weighted IEC/DIN 651)
Maximum S.P.L. :134dB (THD£0.5%, 1kHz)
Dynamic Range :112dB
Power Supply :48V Phantom Power
(IEC 268-15/DIN45596)
Current Consumption :3.5mA
Dimensions :?20mm x 150mm
Net Weight :130g (MC10 x 1)
Full Package Weight :865g
| This new mic is a performance / price breakthrough. It has an acoustically identical version of the legendary CK1 capsule that is permanently mounted. This combination can handle high output transients as well as subtle harmonics. Also included are switchable 75 and 150Hz 12dB per octave rolloff, and switchable -10 & -20 dB input pad. It is a single pattern (cardioid), and has a frequency response of 20 to 20kHz with 135 dB SPL. Requires 12 to 48V phantom power. Kit comes with bag, windscreen and clip.
For more than twenty years, the AKG C 451 with the CK 1 condenser capsule was a standard item on tour riders for sound companies and required by leading engineers for studio projects. When it was discontinued in 1993, there was still a big demand for this microphone. AKG now has an updated version of this classic microphone.
The new C 451B provides the same frequency response as the legendary CK 1 with the same slight high-end rise that was the signature of the original. This characteristic makes the C 451B an ideal tool for capturing signals rich in transients such as acoustic guitars, snare drums, hi-hats and for overhead micing of drum kits. The C 451B?s response eliminates the need for heavy EQ on these instruments.
The new C 451B has also benefited from newer electronic technology with machine soldering and surface-mount components that improve noise performance and make the microphone much more reliable than the original.
Other special features include switchable 10 dB and 20 dB preattenuation pads and switchable low cut filters at 75 Hz or 150 Hz. Standard accessories included are an SA 40 stand adaptor, W 90 windscreen and a rugged zippered bag. Each C 451B also comes with an individual frequency response printout.
Three-year warranty.
Specification
Polar pattern: cardioid
Frequency range: 20?20,000 Hz
Sensitivity: 9 mV/Pa (-41 dBV re 1 V/Pa)
Max. SPL for 0.5 % THD: 135/145/155 dB SPL (-0/-10/-20 dB)
Equivalent noise level: 18 dB-A to DIN 45 412
Signal/noise ratio (A-weighted): 76 dB
Preattenuation pad: switchable, 0, -10,-20 dB Bass cut filter: switchable to flat or 12 dB/octave at 75 Hz or 150 Hz
Electrical impedance: Recommended load impedance: >1.000 Ohms
Power requirement: 9?52 Volt phantom power to DIN 45 596/IEC 268-15
Current consumption: Connector: 3-pin male XLR
Finish: satin nickel plated
Size: dia.: 190 mm (0.7 in.); length: 160 mm (6.3 in.)
Net/shipping weight: 125/760 g (4.4 oz./1.7 lbs.)
Standard accessories: W 90 windscreen, SA 40 stand adapter |
The R?DE NT6 is specifically designed for difficult mounting applications. Although
clearly relevant to instrument mic'ing, the new NT6 is extremely well suited to any
situation where a small 'unobtrusive' but powerful microphone system is required.
The NT6 utilises the 1/2" (externally biased) gold sputtered true condenser transducer
used in the internationally renowned R?DE NT5. The capsule is designed to attach to
a custom made, multi-position swivel mount allowing it to be independently positioned
with ease.
To further increase the versatility of the NT6, it is supplied with 2 thread adaptors - 1/4"
to 5/8" and 1/4" to 3/8" that enable the capsule assembly to be securely attached to a
wide variety of mic stands, tripods and boom poles.
The capsule is connected to the pre-amplifier (body) by a custom 3 m Kevlar? fibre reinforced
cable. Housed within the heavy duty satin-nickel-plated body, is a state-of-the-art low noise
balanced output preamplifier, exhibiting a wide dynamic range and full frequency response.
The surface-mount pre-amplifier circuit also incorporates a 2-position variable pad: 0 dB an -10 dB
attenuation, and a 2-position variable high-pass filter that enables you to step from a flat response
to 80 Hz high pass filter; both conveniently located away from the capsule, providing additional
control without the need to move the capsule once in position.
The NT6 is intended for Film, Television, Broadcast, Live Performance, Theatre, Television,
Surround and Environmental recording applications or wherever your imagination takes you.
The NT6 is produced in R?DE's design and manufacturing facility in Sydney, Australia. Utilising
state of the art computer controlled machining and assembly technologies, R?DE is able to
achieve levels of finish and repeatability of the most exacting standards and tolerances.
The NT6 comes supplied with Microphone Preamp (Body), Capsule, 3 m Kevlar? fibre reinforced
cable, RM5 Stand Mount, 2-axis Swivel Mount, 2 thread adaptors, ZP1 Zip Pouch and WS5 Wind Shield.
FEATURES:
? 1/2? (externally biased) gold sputtered true condenser capsule ? Heavy duty satin-nickel-plated body
? 2-position variable pad: 0 dB and -10 dB ? 2-position variable high-pass filter: flat and 80 Hz ? Surface
mount technology ? Low noise ? Wide dynamic range ? Full frequency response ? Supplied complete
with 2-axis swivel mount, 2 thread adaptors, M5 clip, WS5 (Black) Wind Shield and Soft Pouch ? Designed
& manufactured in Australia ? Full 2 year guarantee
Operation power:
The NT6 is designed to operate from phantom power to the P48 standard. The NT6 will operate
between 44V and 52V applied with positive polarity to pin 2 and pin 3 of the output XLR connector.
Operation output impedance:
Output Impedance: The NT6 will operate satisfactorily into a load impedance as low as 1 kΩ. If a
load below this is used, the output signal level will be reduced. The NT6 output is balanced between
pin 2 (hot) and pin 3 (cold). Pin 1 is ground.
Acoustic principle:
Externally polarised 1/2" (13mm) pressure gradient condenser
Directional pattern: Cardioid
Frequency range:
40 Hz ~ 20,000 Hz selectable HPF @ 80 Hz/12 dB/octave
Output impedance: 200 Ω
Signal noise ratio din iec 651:
75 dB (1 kHz rel 1 Pa; per IEC651, IEC268-15)
Equvalent noise: 19 dB SPL (per IEC651, IEC268-15)
Maximum spl:
138 dB (@ 1% THD into 1 kΩ)148 dB (@ 1% THD into 1 kΩ) - pad at maximum
Sensitivity:
-38 dB re 1 Volt/Pascal (16 mV @ 94 dB SPL) +/- 2 dB
Dynamic range din iec 651: 119 dB (per IEC651, IEC268-15)
Power supply voltage: 48 Volts (P48)
Weight: 386 grm.
Maximum output voltage: 6 dBu (@ 1% THD into 1 kΩ)
Pin assignment:
3 pin XLR, balanced output between pin 2(+), pin (-) & pin 1 (ground)
|
The ME 67 is a long gun microphone head designed for use with the K6 and K6P powering modules. A highly directional microphone, it can be used where the microphone must be placed at a distance from the sound source. Matt black, anodised, scratch-resistant finish.
Pick-up pattern : lobar
Sensitivity in free field, no load (1kHz) : 50 mV/Pa +- 2,5 dB
Nominal impedance : 200 Ohm (K6)
Min. terminating impedance : 1000 Ohm (K6)
Equivalent noise level : 10 dB
Dimensions : d 22,5 x 343 mm
Weight : 100 g
|
Reviews
There are no reviews yet.