Content |
With solid bass reproduction and extended highs, the Ortofon Scratch stylus is great for any style, providing energetic, in-your-face sound. Heavy duty scratch performance guaranteed!
Replacement stylus to be used in Ortofon Scratch OM and Concorde cartridges. For DJs who require increased tracking ability, the Ortofon Scratch cartridge is up to the task. Featuring a reinforced rubber suspension, DJs need not to worry about compromising sound quality and stylus life when working with higher tracking forces. With solid bass reproduction and extended highs, the Ortofon Scratch cartridge is great for any style, providing energetic, in-your-face sound.
Designed with the help of various DJs, the Ortofon Scratch cartridge has been developed for rigorous scratching and back-cueing. It is also constructed of a fluorescent neon-red material creating a luminous effect in certain lighting.
Heavy duty scratch performance guaranteed!
Ortofon Scratch Cartridge Specifications:Frequency response: 20 to 20.000 Hz
Output: 7mV
Channel separation nominal: 25dB
Inductance: 450mH/ch
Weight: 5g
Tracking force: 3 to 5 grams
Recommended load: 47K ohms 200pf
Stylus tip: Spherical
|
This replacement stylus is designed for playback on coded vinyl. It has a superior tracking ability and causes low record wear. It is a spherical stylus with an output of 8.0 mV. |
Genuine Original Stylus for OM 20, OM 20 Super, OMP20, LM 20, Concorde 20, TM 20
Nude Elliptical
| DJ S Replacement stylus
DJ S is a solid-built cartridge in a blue nylon material. It has a fine spherical stylus and a special developed and extremely balanced cantilever that provides outstanding rigidity.
Not only does the cartridge have a most sufficient tracking ability, it is also nearly unbreakable and provides the DJs with the most needed stringency. Furthermore, it equals very low record wear, an advantage for busy DJ. The DJ series has been known to many as the "jack of all trades," with improved tracking, alongside of accurate sound reproduction. Featuring a low wear stylus design, the DJ provides excellent groove handling, even with less weight applied.
The DJ series of cartridges are great for any style of music, and has been a favored choice of DJs around the world!
DJ S Stylus Technical data
Output voltage at 1000Hz, 5cm/sec. - 6 mV
Channel balance at 1kHz - 2 dB
Channel separation at 1kHz - 23 dB
Channel separation at 15 kHz - 15 dB
Frequency range at -3dB - 20-20.000 Hz
Frequency response - 20-18.000 Hz 3dB/-2dB
Tracking ability at 315 Hz at recommmende tracking force - 80 μm
Compliance, dynamic lateral - 9 μm/m N
Stylus type - Spherical
Stylus tip radius - R 18 μm
Tracking force range - 2,0-4,0 g (20-40 mN)
Tracking force recommended - 3,0 g (30 mN)
Tracking angle - 20°
Internal impedance, DC resistance - 750 Ohm
Internal inductance - 450 mH
Recommended load resistance - 47 kOhm
Recommended load capacitance - 200-600 pF
Cartridge weight - 18,5 g
Compatible with cartridges - DJ S | Stylus 2M Blue
Technical data |
|
Frequency range |
20-25.000 Hz |
Frequency response |
20-20.000 Hz + 2 / - 1 dB |
Tracking ability at 315Hz at recommended tracking force *) |
80 µm |
Compliance, dynamic, lateral |
20 µm/mN |
Stylus type |
Nude Elliptical |
Stylus tip radius |
r/R 8/18 µm |
Equivalent stylus tip mass |
0,5 mg |
Tracking force range |
1,6-2,0 g (16-20 mN) |
Tracking force, recommended |
1,8 g (18 mN) |
Tracking angle |
20° |
Stylus colour |
Blue |
|
|
Recommended for following cartridges |
2M Blue |
*) Typical value | Ortofon 310 Stylus Technical Data
- Frequency range 20-20.000 Hz
- Frequency response 20-18.000 Hz + 2 / - 3 dB
- Tracking ability at 315Hz at recommended tracking force 60 µm
- Compliance, dynamic, lateral 20 µm/mN
- Stylus type Elliptical
- Stylus tip radius r/R 8/18 µm
- Equivalent stylus tip mass 0,5 mg
- Tracking force range 1,25-1,75 g (12,5-17,5 mN)
- Tracking force, recommended 1,5 g (15 mN)
- Tracking angle 20°
- Stylus colour Grey
- Recommended for following cartridges Series 310 Universial
|
|
Reviews
There are no reviews yet.