RODE NT-2A Multipattern Condenser Microphone

NT2-A - ?The Legend Continues? Multi Pattern 1? Condenser Microphone.
 
The new NT2-A carries on the tradition forged by the now legendary R?DE NT2.
A professional large capsule (1?) studio microphone incorporating three-position
pick-up patterns, pad and high pass filter switches conveniently located on the
mic body.
At the heart of the NT2-A is the Australian designed and manufactured HF1 dual
diaphragm capsule. The frequency and transient response of this new transducer
has been voiced to complement today?s modern recording techniques, and yet still
evoke the silky smooth character of the legendary microphones of the 50?s and 60?s.
These features provide the flexibility and superlative audio characteristics that make
the NT2-A one of the most versatile condenser mics available.
The NT2-A?s variable controls allow switching between Omni, Figure 8, and Cardioid
polar patterns. The three position high-pass filter provides a flat response or an 80Hz
and 40Hz high pass filter to be selected. Finally the microphones Pad can be switched
between 0 dB, -5dB and -10dB. The NT2-A comes in a soft pouch with an M2 stand mount.
 
SPECIFICATIONS:
Features:
The Australian designed and manufactured HF1 1? edge terminated, gold sputtered, dual
5 um diaphragm capsule. 3-position variable polar pattern: Omni, Cardioid & Figure 8; all
controlled on the mic. 3-position variable high-pass filter: Flat, 80 Hz or 40 Hz. 3-position
variable pad: 0 dB, -5 dB or -10 dB. Ultra low noise, transformerless SMT circuitry. Wide
dynamic range. High strength heat-treated steel mesh head. Durable satin nickel finish.
Internal capsule shock mounting. Supplied complete with soft pouch and clip. Designed
and manufactured in Sydney, Australia.
Operation power:
The NT2-A is designed to operate from phantom power to the P48 standard. The NT2-A will
operate between 44V and 52V applied with positive polarity to pin 2 and pin 3 of the output
XLR connector.
Operation output impedance:
The NT2-A will operate satisfactorily into a load impedance as low as 1 kΩ. If a load below this
is used, the output signal level will be reduced. The NT2-A output is balanced between pin 2 (hot)
and pin 3 (cold). Pin 1 is ground.
Acoustic principle: Externally polarized 25 mm (1?) dual diaphragm.
Directional pattern: Multi-pattern
Frequency range:  20 Hz ~ 20 000 Hz
Output impedance: 200 Ω
Signal noise ratio din iec 651:
87 dB (1 kHz rel 1 Pa; per IEC651, IEC268-15)
Equvalent noise: 7 dBA SPL (per IEC651, IEC268-15)
Maximum spl:
147 dB (@ 1% THD into 1 kΩ); 157 dB (@ 1% THD into 1 kΩ) - pad at maximum
Sensitivity: -36 dB re 1 Volt/Pascal; (16 mV @ 94 dB SPL) +/-2 dB
Dynamic range din iec 651: 140 dB (per IEC651, IEC268-15)
Power supply voltage: 48 Volts (P48)
Output connection:
3 pin XLR, balanced output between; pin 2(+) and pin 3(-); Pin 1 ground
Weight with battery: 860 grm

K2 - ?It cant be done?? Precision Variable Pattern Dual 1? Condenser Valve Microphone.
 
The R?DE K2 is the result of designing and building 1000?s of valve microphones. The
K2?s HF-1 capsule is the pinnacle of transducer technology. The sound quality combines
modern high-end specifications with the character and subtleties of the legendary 50?s mics.
Infinitely variable control of the K2?s polar patterns provides the freedom and flexibility to
excel in any recording situation. The K2 is another example of R?DE?s commitment to
building quality studio microphones to meet the exacting standards demanded by today?s
professionals.At the 2004 Frankfurt Music Messa, 56 of the most prestgious music industry
magazines voted the K2 the ?Best Studio Microphone of 2004?.

SPECIFICATIONS:
Features:
? New large capsule with gold sputtered diaphragm. ? Ultra low noise.
? Wide dynamic range. ? Class ?A? valve circuitry. ? Hand-selected and
graded 6922 twin-triode valve. ? Dedicated Power Supply. ? High strength
welded and heat-treated steel mesh head. ? Durable satin nickel finish.
? Internal capsule shock mounting. ? High level of RF rejection. ? Supplied
complete with SM2 Shock Mount and RC2 Custom Carry Case.
? Continuously variable polar patterns. From omni, through cardiod to
figure 8, controlled at the power supply.
Operation power:
The K2 is designed to operate from a dedicated power supply (110 - 120 V/220 - 240 V, 50/60 Hz)
Acoustic principle: Externally polarized 25 mm(1?) condenser.
Directional pattern:
Continuously variable multi pattern -Omni, through Cardioid to figure 8.
Frequency range:  20 Hz - 20 kHz
Output impedance:
Valve impedence converter with bipolar output buffer.
Signal noise ratio din iec 651:
 > 81 dB (1kHz relative to 1 Pa; per IEC651,IEC268-15).
Equvalent noise:  10 dBA SPL (per IEC651, IEC268-15).
Maximum spl: 162 dB (@ 1% THD into 1k).
Sensitivity:
 -36 dB re 1 Volt/Pascal (16 mV @ 94 dB SPL) +/- 2 dB.
Power supply voltage:
Dedicated Power Supply(110 - 120 V/220 - 240 V, 50/60 Hz).
Weight:  815 gms
Dimensions width:  208.5 mm
Dimensions depth:  55 mm
Dimensions height:  55 mm
Maximum output voltage:  > +30 dBu (@ 1% THD into 1 k).

NT2000 - ?Explore, Control, Create?? Seamlessly Variable Dual 1? Condenser Microphone.

The world's first large diaphragm condenser studio microphone with seamlessly variable Polar
Patterns, Filter and Pad located conveniently on the microphone body. The NT2000?s state of
the art surface-mount electronics combined with the new Australian designed and manufactured
HF1 Capsule, provide extremely low self-noise (7 dBA) and a maximum SPL of 147 dB (157 dB
with pad fully engaged) ensuring exceptional results and the ultimate in recording creativity.
The NT2000 is supplied with the SM2 Shock Mount, together in a durable custom carry case.

SPECIFICATIONS:
Acoustic principle:
Externally polarised 25 mm (1?) dual diaphragm condenser
Directional pattern: Multipattern
Frequency range:  20Hz - 20KHz
Output impedance: 200 ohms
Signal noise ratio din iec 651:  87 dB (1kHz rel 1Pa)
Equvalent noise: 7 dBA SPL (per IEC651, IEC268-15)
Maximum spl:
147 dB (@ 1% THD into 1K ohm) 157dB (@ 1% THD into 1K ohm) with pad set to maximum
Sensitivity:
-36 db re 1 Volt/Pasca (16 mv @94db SPL) +/- 2 dB
Dynamic range din iec 651: 140 dB (per IEC651, IEC268-15)
Power supply voltage: Phantom P48
Weight without battery: 831 gm
Weight with battery:  2.6 kg
 

• Professional large-diaphragm condenser microphone for unsurpassed audio quality
• Ideal as main and support microphone for studio and live applications
• Exceptionally flat frequency response and ultra-high sound resolution
• Cardioid pickup pattern for outstanding sound source separation and feedback rejection
• Ultra low-noise transformerless FET input circuitry
• LED indicates phantom power operation
• Gold-plated 3-pin XLR output connector for perfect signal transmission
• Ultra-rugged construction with die-cast body
• Swivel stand mount and carrying case included

• Large 1" (25mm) capsule with gold plated diaphragm
• Cardioid polar pattern
• Self noise of only 5dB (A)
• Ultra low noise, transformerless surface mount circuitry
• Wide dynamic range
• Gold plated output contacts
• True condenser (externally biased)
• Internal capsule shock mounting