Content | LD Systems STINGER 12 A G2
12" active PA Speaker
Stinger 12 G2 Active Full-Range Speaker
The Stinger 12 G2 is an active, full-range speaker that is suitable for use in portable PA systems, as a monitor, and in permanent installations.
The 2-way bass reflex design made of sturdy multiplex is loaded with a 12" woofer and a 1" BMS HF driver that attain a high maximum sound pressure level of 118dB (132dB peak). It is powered by the built-in Hypex Ucd400 Class D power amp with a peak power rating of 1600W / 4 ohms. An integral 2-band EQ is provided for tone control. The inputs are XLR/jack combo connectors. The output is an XLR connector. A Speakon-compatible power amp output permits parallel operation of passive speakers and subwoofers.
The hardware includes a stand support that is vertically adjustable by ±13.5° max. in seven increments for optimum orientation, six mounting holes for flyware, and LD "Evolutive" handles. These innovative carrying handles offer a secure grip from all sides for easier transport. Mounting brackets and a protective cover are available as accessories.
Product type
PA loudspeaker
Low/mid driver dimensions
12 "
Low/mid driver dimensions (mm)
304.8 mm
Woofer voice coil (mm)
63.5 mm
HF driver dimensions (mm)
25.4 mm
HF driver voice coil (mm)
25.4 mm
Amplifier
Class D, Hypex Ucd400
Dispersion (H x V)
100 x 55 °
Frequency response
58 - 19000 Hz
Crossover frequency
1800 Hz
Max. SPL (continuous)
118 dB
Protection circuits
HF Driver , over voltage , over-current
Input sensitivity
- 5 dBu
Controls
Bass , Line Gain , Mic Gain , Power , Treble , volume
Indicators
limit , Power , protect (protection circuit engaged) , signal
Line input connectors
6.3 mm Jack , XLR
Mic inputs
6.3 mm Jack , XLR
Line output connectors
XLR
Speaker output connections
Speakon compatible
Minimum impedance of connected speakers
8 Ohm(s)
Operating voltage
Switching Power Supply
Operating voltage
220 V AC - 240 V AC, 50-60 Hz
Cabinet material
15 mm Plywood
Cabinet surface
texture paint
Cabinet construction
vented
Features
*Short Term Max. SPL Peak @ 1m with Pink Noise , 6 x M8 flying points , LD Systems "Evolutive" handles , SM707 stand mount 36 mm
|
Key Features:
- Compact Powered bi-amplified
full-range loudspeaker with JBL
DrivePack® technology for portable or
installed use
- Optimized for both portable/rental or
permanent-venue use
- 1750 watts peak output power,
875 watts continuous
- 12-inch Differential Drive® lowfrequency
driver for extended lowfrequency
output
- Robust powder-coated die cast
aluminum handles, designed for
strength and comfort
- Integrated 35 mm stand mount
Specifications:
Frequency Response (+/-3 dB): 65 Hz - 18 kHz80 Hz – 20 kHz
Frequency Range (-10 dB): 55 Hz - 20 kHz50 Hz – 20 kHz
Coverage Pattern: 90° x 50°
Directivity Factor (Q): 12.6
Directivity Index (DI): 11 dB
Maximum Peak Output1: 134 dB SPL 1m
Transducer Section:
Low Frequency Section: JBL 2262FF, 304 mm (12 in) dia., 76 mm (3 in) Dual Coil
neodymium Differential Drive®, Direct Cooled
Bandpass Nominal Impedance: 2 x 2 ohms
High Frequency: JBL 2452H-SL, 100 mm (4 in) titanium damped
diaphragm, 1.5 in. exit.
Bandpass Nominal Impedance: 8 ohms
System:
DPC1 Internal Amplification Output
(at nominal load) 1750 Watts Peak, 875 Watts Continuous
DPC1 Output (Continuous IEC shaped
pink noise into rated load impedance): 750LF/125HF Watts
DPC1 Output Section: LF: Dual Bridged Technology™, Class D
HF: Bridged Class D
Audio Input connector XLR with loop-through
User Controls: 80 Hz Subwoofer High Pass Filter. Enable/Disable
0-16 dB input Attenuator with 32 precision 0.5 dB steps
Signal Processing: DSP based, resident in Input Module.
System Management: DSP based limiters for mechanical and thermal
protection
AC Power Operating Range: 90-132 VAC/216-264 VAC, 50/60 Hz
AC Line Voltage: 50/60 Hz; User Selectable; 120V/240V (-15%, +10%)
AC Input Connector: Neutrik PowerCon (NAC 3MPA)
AC Loop-thru: Neutrik PowerCon (NAC 3MPB)
AC Current Requirement: 6A per system at 120V, 3A per system at 240V
Enclosure:
Box Construction: 5/8 in. multi-ply exterior grade Baltic birch. Internally
braced. Black DuraFlex™ finish.
Suspension System: 9 M10 Fittings + 2 M6 Fittings, 35 mm pole mount
socket
Grille: 14 Gauge Black powder-coated perforated steel with
foam backing.
Dimensions (H x W x D): 533 x 358 x 334 mm
21.0 x 14.1 x 13.1 in
Net Weight: 21.3 kg (47 lb)
|
The LDMON101A features a high end 10" co-axial speaker with a 1" compression driver and delivers 150 W RMS output power.
The Volex power supply system allows a secure connection of further active monitors, this feature enables the installation of a big active stage monitor system while using only one power plug. The monitor also features a softclip-limiter as well as a volume control.
The Housing was built out of a high quality plywood with a high resistance textured finish. The stabile front guard ideally protects the speakerbox.
Specifications LDMON101A: - Model Name: LDMON101A
- Type: Bass Reflex
- Components:
- Woofer / Compression Driver: 10" / 1" Coaxial Custom Made Speaker
- Amplification: Class A / B
- Dispersion: 75° x 75°
- Power: 150 W RMS
- Frequency Range: 90 Hz- 20 Khz
- SPL (1 W / 1 m): 99 dB
- Max. SPL: 121 dB
- Protection: Limiter, Circuit and Overcurrent
- Controls: Volume, On/Off Switch
- Indicators: Signal, Power, Limit
- Connectors:
- Input: Line: XLR /6,3 mm jack (combo)
- Output: Line: XLR
- Power Supply: Transformer
- Cabinet Material: 15 mm Plywood
- Cabinet Surface: Painting
- Dimensions: 360 x 370 x 425 mm
- Features: Ergonomic milled handles, VOLEX power plug input / output
|
- 1000w RMS, 2000w peak, power delivers clarity, punch and more than enough headroom for any
- performance or practice space
- Specially-voiced 12-inch woofer and high frequency compression driver deliver your drum sounds
- with precise, full response across the entire frequency range without any artificial colouration
- (2) XLR/TRS 1/4-inch combo inputs with independent volume controls and clip indicator
- XLR output to link another Strike Amp 12 or send your performance to another input device
- Lightweight and flexible tilt-back cabinet design that can also be pole-mounted
- Contour EQ switch to control your sound
- Ground-Lift switch eliminates unwanted noise
Specifications:
- Output: Power 2000W (peak, 1300LF + 700HF), 1000W (continuous RMS, 650LF + 350HF)
- Low-Frequency: 12.0” (305mm) low-frequency driver, 3.0” (76mm) high-temperature voice coil
- High-Frequency: 1.4” (35mm) voice coil, neodymium-magnet high-frequency driver with precision waveguide
- Crossover Frequency: 2.0KHz
- Maximum SPL: 131dB (peak), 128dB (continuous) (dB-SPL @ 1m)
- Frequency Response: 53Hz – 20kHz (+3dB)
- Frequency Range: 46Hz – 22kHz (-10dB)
- Horn Coverage 90o horizontal x 60o vertical (nominal)
- Equalisation: Contour switch with low- and high-frequency +3dB boost
Connectors: - (2) XLR/TRS 1/4” (6.35mm) combo inputs - (1) XLR link output - (1) IEC power cable input
- Controls Power switch, (2) volume control knobs (1 per input), EQ contour switch, ground-lift switch
- Indicators: (2) power LEDs (1 front-panel, 1 rear-panel), clip limiter LED
- Protection: Electronic clip, thermal & transducer overdrive
- Input Voltage: 100V~, 110–120V~, 220–240V~; 50/60Hz (switchable)
- Fuse: 100–120V T10AL AC250V 220–240V T5AL AC250V
- Consumption: 800W
- Enclosure: Trapezoidal, injection-molded polypropylene enclosure with perforated steel grille
Dimensions: (width x depth x height) 605 x 354 x 350mm Weight: 16.3kg |
Key Features:
- Compact Powered bi-amplified
full-range loudspeaker with JBL
DrivePack® technology for portable or
installed use
- Optimized for both portable/rental or
permanent-venue use
- 1750 watts peak output power,
875 watts continuous
- 15-inch Differential Drive® lowfrequency
driver for extended lowfrequency
output
- Robust powder-coated die cast
aluminum handles, designed for
strength and comfort
- Integrated 35 mm stand mount
Specifications:
Frequency Response (+/-3 dB): 60 Hz - 18 kHz80 Hz – 20 kHz
Frequency Range (-10 dB): 45 Hz - 20 kHz50 Hz – 20 kHz
Coverage Pattern: 90° x 50°
Directivity Factor (Q): 12.6
Directivity Index (DI): 11 dB
Maximum Peak Output1: 135 dB SPL 1m
Transducer Section:
Low Frequency Section: JBL 2265FF, 381 mm (15 in) dia., 76 mm (3 in) Dual Coil
neodymium Differential Drive®, Direct Cooled
Bandpass Nominal Impedance: 2 x 2 ohms
High Frequency: JBL 2452H-SL, 100 mm (4 in) titanium damped
diaphragm, 1.5 in. exit.
Bandpass Nominal Impedance: 8 ohms
System:
DPC1 Internal Amplification Output
(at nominal load) 1750 Watts Peak, 875 Watts Continuous
DPC1 Output (Continuous IEC shaped
pink noise into rated load impedance): 750LF/125HF Watts
DPC1 Output Section: LF: Dual Bridged Technology™, Class D
HF: Bridged Class D
Audio Input connector XLR with loop-through
User Controls: 80 Hz Subwoofer High Pass Filter. Enable/Disable
0-16 dB input Attenuator with 32 precision 0.5 dB steps
Signal Processing: DSP based, resident in Input Module.
System Management: DSP based limiters for mechanical and thermal
protection
AC Power Operating Range: 90-132 VAC/216-264 VAC, 50/60 Hz
AC Line Voltage: 50/60 Hz; User Selectable; 120V/240V (-15%, +10%)
AC Input Connector: Neutrik PowerCon (NAC 3MPA)
AC Loop-thru: Neutrik PowerCon (NAC 3MPB)
AC Current Requirement: 6A per system at 120V, 3A per system at 240V
Enclosure:
Box Construction: 5/8 in. multi-ply exterior grade Baltic birch. Internally
braced. Black DuraFlex™ finish.
Suspension System: 13 M10 Fittings, 35 mm pole mount socket
Grille: 14 Gauge Black powder-coated perforated steel with
foam backing.
Dimensions (H x W x D): 613 x 434 x 359 mm
24.1 x 17.1 x 14.1 in
Net Weight: 24.7 kg (55 lb)
|
LD Systems Stinger MON121AG2 The LD Stinger MON121AG2 is a compact active stage monitor for all mobile applications. The specially developed 12" coaxial speaker with an integral 1" HF driver and powerful ferrite magnets stands out because of a precisely symmetrical dispersion over 75° x 75° and attains a maximum sound-level pressure of 124dB with maximum resistance to feedback. It is driven by a Class AB power amplifier with a power output of 250W RMS. The frequency response curve is 80Hz - 20kHz. Dependable operation of the LD MON121AG2 is ensured by a limiter that prevents overloading of the speaker and a protection circuit that guards against short-circuiting. The input is a XLR-jack combo socket, an XLR output permits looping through of the signal. Other connector panel features include a volume control, IEC power socket, LED indicators of various colours for power, signal, and the limiter function. The elegant looking bass-reflex enclosure of the LD MON121AG2 is made of 15mm-thick multiplex finished with a durable coating. A sturdy metal grille guards against speaker damage, and ergonomically milled handles make transport easier. The monitor angle is 35°. - Type: active
- Woofer size: 12“
- Woofer size: 304 mm
- Woofer type: coaxial speaker
- Woofer magnet: ferrite
- Woofer brand: custom made
- Woofer voice coil: 2
- Woofer voice coil: 50.8 mm
- HF driver size: 1“
- HF driver size: 25.4 mm
- HF driver magnet: ferrite
- HF driver brand: custom made
- HF driver voice coil: 1“
- HF driver voice coil: 25.4 mm
- Amplifier: Class A / B
- Dispersion angle (H x V): 75° x 75°
- Power output (RMS): 250 W
- Power output (peak): 500 W
- Frequency response: 80 Hz - 20 kHz
- Crossover frequency: 2200 Hz
- SPL (1 W/1 m): 100 dB
- Max. SPL (continuous): 116 dB
- Max. SPL (peak): 124 dB
- Protection: limiter, short-circuit
- Controls: Volume, On / Off
- Indicators: Power, Signal, Limit
- Number of line inputs: 1
- Line input connectors: XLR/ 6.3 mm jack (combo)
- Number of line outputs: 1
- Line output connectors: XLR
- Power supply: transformer
- Operating voltage: 230 V AC / 50-60 Hz
- Cabinet material: 15 mm plywood
- Cabinet type: bass reflex
- Monitor angle: 35°
- Width: 440 mm
- Depth: 360 mm
- Height: 514 mm
- Features: Ergonomic insert handles
|
Reviews
There are no reviews yet.