Content | LD Systems STINGER 12 A G2
12" active PA Speaker
Stinger 12 G2 Active Full-Range Speaker
The Stinger 12 G2 is an active, full-range speaker that is suitable for use in portable PA systems, as a monitor, and in permanent installations.
The 2-way bass reflex design made of sturdy multiplex is loaded with a 12" woofer and a 1" BMS HF driver that attain a high maximum sound pressure level of 118dB (132dB peak). It is powered by the built-in Hypex Ucd400 Class D power amp with a peak power rating of 1600W / 4 ohms. An integral 2-band EQ is provided for tone control. The inputs are XLR/jack combo connectors. The output is an XLR connector. A Speakon-compatible power amp output permits parallel operation of passive speakers and subwoofers.
The hardware includes a stand support that is vertically adjustable by ±13.5° max. in seven increments for optimum orientation, six mounting holes for flyware, and LD "Evolutive" handles. These innovative carrying handles offer a secure grip from all sides for easier transport. Mounting brackets and a protective cover are available as accessories.
Product type
PA loudspeaker
Low/mid driver dimensions
12 "
Low/mid driver dimensions (mm)
304.8 mm
Woofer voice coil (mm)
63.5 mm
HF driver dimensions (mm)
25.4 mm
HF driver voice coil (mm)
25.4 mm
Amplifier
Class D, Hypex Ucd400
Dispersion (H x V)
100 x 55 °
Frequency response
58 - 19000 Hz
Crossover frequency
1800 Hz
Max. SPL (continuous)
118 dB
Protection circuits
HF Driver , over voltage , over-current
Input sensitivity
- 5 dBu
Controls
Bass , Line Gain , Mic Gain , Power , Treble , volume
Indicators
limit , Power , protect (protection circuit engaged) , signal
Line input connectors
6.3 mm Jack , XLR
Mic inputs
6.3 mm Jack , XLR
Line output connectors
XLR
Speaker output connections
Speakon compatible
Minimum impedance of connected speakers
8 Ohm(s)
Operating voltage
Switching Power Supply
Operating voltage
220 V AC - 240 V AC, 50-60 Hz
Cabinet material
15 mm Plywood
Cabinet surface
texture paint
Cabinet construction
vented
Features
*Short Term Max. SPL Peak @ 1m with Pink Noise , 6 x M8 flying points , LD Systems "Evolutive" handles , SM707 stand mount 36 mm
|
The LDMON101A features a high end 10" co-axial speaker with a 1" compression driver and delivers 150 W RMS output power.
The Volex power supply system allows a secure connection of further active monitors, this feature enables the installation of a big active stage monitor system while using only one power plug. The monitor also features a softclip-limiter as well as a volume control.
The Housing was built out of a high quality plywood with a high resistance textured finish. The stabile front guard ideally protects the speakerbox.
Specifications LDMON101A: - Model Name: LDMON101A
- Type: Bass Reflex
- Components:
- Woofer / Compression Driver: 10" / 1" Coaxial Custom Made Speaker
- Amplification: Class A / B
- Dispersion: 75° x 75°
- Power: 150 W RMS
- Frequency Range: 90 Hz- 20 Khz
- SPL (1 W / 1 m): 99 dB
- Max. SPL: 121 dB
- Protection: Limiter, Circuit and Overcurrent
- Controls: Volume, On/Off Switch
- Indicators: Signal, Power, Limit
- Connectors:
- Input: Line: XLR /6,3 mm jack (combo)
- Output: Line: XLR
- Power Supply: Transformer
- Cabinet Material: 15 mm Plywood
- Cabinet Surface: Painting
- Dimensions: 360 x 370 x 425 mm
- Features: Ergonomic milled handles, VOLEX power plug input / output
|
The tops of the LDBLOCKX Power Tower are fitted with 12" custom made midrange speakers and a 1" Celestion Driver, they are driven by a 450 W RMS Bi-Amp amplifier producing a maximum sound pressure level of 128 dB.
Specifications LD Block X 12" Topteil Active: - Model Name: LDATOP12
- Type: Bassreflex
- Components:
- Woofer: 12" Custom Made
- Compression Driver: 1" Custom Made
- Amplification: Class A / B (Bi-Amp)
- Dispersion: 60° x 40°
- Power (RMS): 350 W + 100 W
- Frequency Range: 80 Hz - 20 kHz
- SPL (1 W/ 1 m): 101 dB
- Max SPL: 128 dB
- Protection: Limiter, Thermal, DC, Short circuit, HF
- Controls: Main Volume, Tweeter Volume, switchable High Pass (80 / 120 Hz), On/Off Switch
- Indicators: Power, Limiter, Signal, Protect
- Connectors:
- Input: Line: XLR + Jack 6,3mm (Combo)
- Output: Line: XLR
- Power Supply: Transformer
- Cabinet Material: 15 mm Plywood
- Cabinet Surface: Painting
- Dimensions (W x H x D): 450 x 500 x 520 mm
- Features: Ergonomic milled handles
|
The NX 10-SMA is equipped with new high power 400 W digital amplifier and a newly designed 10 " coaxial neodymium transducer that guarantees outstanding audio quality and definition as well as an extremely lightweight of the final system. The NX 10-SMA can be also used as a portable PA system, thanks to the rugged powder coated steel pole mount installed on the side. In order to control the response of the speaker in such different applications, RCF has incorporated two special Equalization Modes: - Floor, for stage monitoring; - Free Field, for the use of the speakers as a stand-alone PA system. Cabinet is made in Baltic Birch plywood, finished with an extremely resistant paint for an extensive use on the road. An ergonomic side handle, integrated with the input panel, is provided for an easier transport of the speaker.
APPLICATIONS
- • Main vocal stage monitor
- • Drum or keyboard monitor
- • Main PA in small venues
General Specs
- 800 Watt Peak, 400 Watt RMS digital bi-amplification
- 127 dB max spl
- 60° x 60° constant directivity horn
- 10" High power neodymium woofer, 2.5" voice coil
- 7 kapton dome, 1" exit, neodymium high frequency driver
- DSP processing, floor - fre field equalization, soft limiter and protection
- Combo xlr/jack input, xlr signal output
Acoustical Specs
- Frequency Response -3 dB:60Hz ÷ 20000 Hz
- Max SPL:127dB
- Horizontal coverage angle:60°
- Vertical coverage angle:60°
- Compression Driver:7 kapton dome, 1" exit, neodymium
- Woofer:10" neo high power woofer, 2.5" voice coil
Processor Section
- Limiter:Soft Limiter
- Controls:Freefield, floor
Amplifier Specifications
- Total power:800W PEAK
- High frequencies:200 W PEAK
- Low frequencies:600 W PEAK
- Total power:400W RMS
- High frequencies:100 W RMS
- Low frequencies:300 W RMS
Cabinet Specs
- Cabinet Material:Baltic Birch
- Handles:1 on side
- Pole Mount/Cap:yes
- Grille:steel
Size/Weight
- Height:324/12.7mm/inch
- Width:450/17.7mm/inch
- Depth:417/16.4mm/inch
- Net Weight:14,5/31.96kg/lbs
|
Features
400 Watt digital bi-amplification
128 dB max spl
Wide dispersion 90 x 60 constant directivity horn
12" High power woofer, 3" voice coil
2" Titanium dome, high frequency driver
DSP processing, boost eq, soft limiter and protection
Xlr/jack input, xlr signal output
Acoustical Specifications
Frequency Response -3 dB: 45 Hz ÷ 20 kHz
Max SPL: 128 dB
Horizontal coverage angle: 90°
Vertical coverage angle: 60°
Compression Driver: 2" 2.5" voice coil
Woofer: 12" 3" voice coil
Input/Output Section
Input connectors: xlr-jack
Output connectors: xlr
Processor Section
Crossover frequencies: 1300 Hz
Controls: Flat, Boost
Amplifier Specifications
Total power: 400 W
High frequencies: 100 W
Low frequencies: 300 W
Cabinet
Handles: 1 on top, 2 on sides
Pole Mount/Cap: yes
Grille: steel
Physical Specifications
Height: 637/25 mm/inch
Width: 384/15.11 mm/inch
Depth: 363/14.2 mm/inch
Net Weight: 20.2/44.53 kg/lbs
|
StageSource™ is designed to be the worldʼs most versatile loudspeaker system for musicians. Using six powerful DSP-based Smart Speaker modes, the StageSource L3m output is optimized for a variety of performance scenarios including front-of-house PA, floor monitor, personal PA, keyboard backline, acoustic guitar backline, or with a multi-effects guitar processor as a high-performance electric guitar speaker system. Onboard accelerometer and pole mount sensors automatically detect the speakerʼs orientation and set the Smart Speaker mode accordingly.
The 1,400-watt, 3-way, tri-amped speaker system and a dual-braced tour-grade plywood enclosure combine to deliver astounding power and reliability. The innovative multi-function design enables the L3m to be the perfect loudspeaker in a wide variety of applications including floor or stage-stacked, pole-mounted, horizontal as a floor monitor, Virtual Tilt-back for instrument backline or flown with the integrated M10 suspension points for installation.
Cabin Type: | Wooden, 3-way | Monitor Use: | Yes | Amplifier: | 1,400‐watt | LF/MF, Woofer: | 2x10” | HF, Horn: | 1” exit compression driver | DSP Processor: | Yes | Frequency Response: | 47 Hz to 18 kHz | Dimensions: | 312 mmx861 mmx 312 mm | Weight: | 26.1 kg | Color: | Black |
|
Reviews
There are no reviews yet.