Content |
EVP-X15PM: powered version for EVP-X12P: 300W(RWS)/500W(PEAK)
2 Channel mixer; high/low EQ control; Balanced line output
SYSTEM TYPE: 15” 2-way monitor - FREQ RESP +/ - 3 DB: 50Hz - 20kHz
- FINISH MATERIAL: Black carpet - TRIPOD STAND BOTTOM: No -
TRIPOD STAND TOP: No - INPUTS: INPUT A: Line level input / INPUT
B: NA - SPEAKER LEVEL INPUT: NA - INPUT CONNECTORS: INPUT
A: Combined Jack and XLR / INPUT B: NA - INPUT SENSITIVITY: MIC:
5mV / RCA: 0.5V / LINE: 0.775V - INPUT IMPEDANCE: MIC: 470
OHMS / LINE INPUT A: 47K / LINE OUTPUT TYPE: Balanced Male XLR
connector - LINE OUTPUT HIGH PASS FILTER: MAIN EQ: 5 band
graphic EQ - ACTIVE CROSSOVER: NA - PHASE SWITCH: NA -
POWER SECTION-AMPLIFIER POWER, CONTINUOUS: 400W -
PEAK: 600W - EXTENSION SPEAKER OUTPUT: 1 - PROTECTION
TYPE: Dynamic/AGC - POWER ON INDICATOR: Green LED - SYSTEM
DYNAMIC AGC: Orange LED - ENCLOSURE - DIMENSION MM
(HXWXD): 645X445X473.5 - WEIGHT (NET) KG: 27.4 - WEIGHT
(GROSS) KG: 30.5
|
- 1000w RMS, 2000w peak, power delivers clarity, punch and more than enough headroom for any
- performance or practice space
- Specially-voiced 12-inch woofer and high frequency compression driver deliver your drum sounds
- with precise, full response across the entire frequency range without any artificial colouration
- (2) XLR/TRS 1/4-inch combo inputs with independent volume controls and clip indicator
- XLR output to link another Strike Amp 12 or send your performance to another input device
- Lightweight and flexible tilt-back cabinet design that can also be pole-mounted
- Contour EQ switch to control your sound
- Ground-Lift switch eliminates unwanted noise
Specifications:
- Output: Power 2000W (peak, 1300LF + 700HF), 1000W (continuous RMS, 650LF + 350HF)
- Low-Frequency: 12.0” (305mm) low-frequency driver, 3.0” (76mm) high-temperature voice coil
- High-Frequency: 1.4” (35mm) voice coil, neodymium-magnet high-frequency driver with precision waveguide
- Crossover Frequency: 2.0KHz
- Maximum SPL: 131dB (peak), 128dB (continuous) (dB-SPL @ 1m)
- Frequency Response: 53Hz – 20kHz (+3dB)
- Frequency Range: 46Hz – 22kHz (-10dB)
- Horn Coverage 90o horizontal x 60o vertical (nominal)
- Equalisation: Contour switch with low- and high-frequency +3dB boost
Connectors: - (2) XLR/TRS 1/4” (6.35mm) combo inputs - (1) XLR link output - (1) IEC power cable input
- Controls Power switch, (2) volume control knobs (1 per input), EQ contour switch, ground-lift switch
- Indicators: (2) power LEDs (1 front-panel, 1 rear-panel), clip limiter LED
- Protection: Electronic clip, thermal & transducer overdrive
- Input Voltage: 100V~, 110–120V~, 220–240V~; 50/60Hz (switchable)
- Fuse: 100–120V T10AL AC250V 220–240V T5AL AC250V
- Consumption: 800W
- Enclosure: Trapezoidal, injection-molded polypropylene enclosure with perforated steel grille
Dimensions: (width x depth x height) 605 x 354 x 350mm Weight: 16.3kg |
The HD 12-A offers an extremely linear response and a precise, deep low frequency control. The 12” woofer guarantee a superior sound projection indoor and outdoor. It is the ideal speaker for main front of house in small PA systems, for high power monitoring and it is the best solution where higher power is required for various applications in larger venues.
APPLICATIONS
- • Live Sound
- • Rental
- • Portable PA
- • Stage Monitoring
- • Clubs
General Specs
1200 WATT PEAK, 600 WATT RMS Digital Bi-amp DSP Sound Processing RCF Precision Transducers 130 dB MAX SPL
Acoustical Specs
Frequency Response -3 dB:45 Hz ÷ 20000 Hz Max SPL:130 dB Horizontal coverage angle:90° Vertical coverage angle:60° Compression Driver:1“, 1.7" voice coil Woofer:12“, 2.5" voice coil
Inputs/Outputs
Input signal:bal/unbal Input connectors:Jack-XLR male Output connectors:XLR female Input sensitivity:-2 dBu / + 4 dBu
Processor Section
Crossover frequencies:1600 Hz Protections:thermal, RMS Limiter:Fast limiter Controls:Volume, EQ shape, Mic/line
Amplifier Specifications
Total power:1200 W PEAK High frequencies:300 W PEAK Low frequencies:900 W PEAK Total power:600 W RMS High frequencies:150 W RMS Low frequencies:450 W RMS Connections:VDE AC socket
Cabinet Specs
Cabinet Material:Composite PP Hardware:1 x M10 top, 1 x M10 bottom, 3 x M6 bottom Handles:1 top, 2 side Pole Mount/Cap:Yes Grille:Steel Colour:Black
Size/Weight
Height:647/25.47 mm/inch Width:380/14.96 mm/inch Depth:380/14.96 mm/inch Net Weight:18.3/40.34 kg/lbs |
Active 300-Watt 2-Way Monitor Speaker System with 12" Woofer, 1" Compression Driver and Feedback Filter High-power 300-Watt 2-way monitor speaker system for live and playback applications Exceptional sound quality, wide frequency bandwidth and dynamic range Revolutionary Class-D amplifier technology: enormous power, incredible sonic performance and super-light weight Adjustable feedback filter and integrated limiter for ultimate system control and speaker protection Integrated sound processor for ultimate system control and speaker protection Ultra-low noise Mic/Line input with Volume control and Clip LED Dedicated 3-band EQ for perfect sound shaping Extremely powerful 12'' long-excursion driver provides incredibly deep bass and acoustic power High-resolution 1'' HF driver for exceptional high-frequency reproduction Proprietary horn design for ultra-wide sound dispersion Internal switch-mode power supply for noise-free audio, superior transient response and very low power consumption Integrated 35 mm pole socket for stand mounting and use as PA system High-quality components and exceptionally rugged construction ensure long life Conceived and designed by BEHRINGER Germany User's Manual
|
The NX 12-SMA is equipped with new high power 700 W digital amplifier and a newly designed 12” coaxial neodymium transducer that guarantees outstanding audio quality and definition as well as an extremely lightweight of the final system. The NX 12-SMA can be also used as a portable PA system, thanks to the rugged powder coated steel pole mount installed on the side. In order to control the response of the speaker in such different applications, RCF has incorporated two special Equalization Modes: - Floor, for stage monitoring; - Free Field, for the use of the speakers as a stand-alone PA system. Cabinet is made in Baltic Birch plywood, finished with an extremely resistant paint for an extensive use on the road. An ergonomic side handle, integrated with the input panel, is provided for an easier transport of the speaker
APPLICATIONS
- • Main vocal stage monitor
- • High-output drum or keyboard monitor
- • Main PA in small venues
General Specs
- 1400 Watt Peak, 700 Watt RMS digital bi-amplification
- 129 dB max spl
- 60° x 60° constant directivity horn
- 12" High power neodymium woofer, 2.5" voice coil
- 1.7 kapton dome, 1" exit, neodymium high frequency driver
- DSP processing, floor - fre field equalization, soft limiter and protection
- Combo xlr/jack input, xlr signal output
Acoustical Specs
- Frequency Response -3 dB:50Hz ÷ 20000 Hz
- Max SPL:129dB
- Horizontal coverage angle:60°
- Vertical coverage angle:60°
- Compression Driver:1.7 kapton dome, 1" exit, neodymium
- Woofer:12" neo high power woofer, 2.5" voice coil
Processor Section
- Limiter:Soft Limiter
- Controls:Freefield, floor
Amplifier Specifications
- Total power:1400W PEAK
- High frequencies:400 W PEAK
- Low frequencies:1000 W PEAK
- Total power:700W RMS
- High frequencies:200 W RMS
- Low frequencies:500 W RMS
Cabinet Specs
- Cabinet Material:Baltic Birch
- Handles:1 on side
- Pole Mount/Cap:yes
- Grille:steel
Size/Weight
- Height:324/12.7mm/inch
- Width:550/21.6mm/inch
- Depth:417/16.4mm/inch
- Net Weight:16,5/36.3kg/lbs
| LD Systems Stinger MON81AG2
The LD Stinger MON81AG2 is an especially compact active monitor with broad frequency response and a maximum sound-level pressure of 116dB for versatile use on stage.
The 8" coaxial speaker with an integral 1" HF driver attains a dispersion angle of 75°x75°, which is beneficial in multifaceted applications as a stage monitor. The coaxial configuration results in a very homogenous sound in the entire dispersion area plus very low susceptibility to feedback. The active monitor is driven by a Class AB power amplifier with an output power of 80W RMS; short-circuit protection and a limiter ensure dependable operation.
The signal is connected and looped through using an XLR/ jack combo socket and the XLR output. The rear connector panel is rounded out by a volume control, LED indicators, and the IEC power socket
The elegant bass-reflex housing made of 15mm multiplex is finished with a durable coating and has ergonomically milled handles and a metal grille to protect the speaker. The monitor angle is 35°.
Type: active
Woofer size: 8“
Woofer size: 203 mm
Woofer type: coaxial speaker
Woofer magnet: ferrite
Woofer brand: custom made
Woofer voice coil: 2
Woofer voice coil: 50.8 mm
HF driver size: 1“
HF driver size: 25.4 mm
HF driver magnet: ferrite
HF driver brand: custom made
HF driver voice coil: 1“
HF driver voice coil: 25.4 mm
Amplifier: Class A / B
Dispersion angle (H x V): 75° x 75°
Power output (RMS): 80 W
Power output (peak): 160 W
Frequency response: 90 Hz - 20 kHz
Crossover frequency: 2.400 Hz
SPL (1 W/1 m): 97 dB
Max. SPL (continuous): 111 dB
Max. SPL (peak): 116 dB
Protection: limiter, short-circuit
Controls: Volume, On / Off
Indicators: Power, Limit
Number of line inputs: 1
Line input connectors: XLR/ 6.3 mm jack (combo)
Number of line outputs: 1
Line output connectors: XLR
Power supply: transformer
Operating voltage: 230 V AC / 50-60 Hz
Cabinet material: 15 mm plywood
Cabinet type: bass reflex
Monitor angle: 35°
Width: 320 mm
Depth: 250 mm
Height: 361 mm
Features: Ergonomic insert handles |
Reviews
There are no reviews yet.