Content | The Swiss Army Knife of microphones
for vocal and instrumental recording, on stage, in ENG/EFP and video production
The C1000 S from AKG is a small-diaphragm condenser microphone with a cardioid pattern designed for recording, live-sound, ENG and video-production applications with vocals and instruments. Using the included polar-pattern converter accessory, the microphone can be switched from cardioid to hypercardioid to reduce feedback when used on stage. The presence-boost adapter offers three discrete frequency settings to add clarity to speech and instrument sounds.
A switchable low-cut filter at 80 Hz helps reduce rumble or wind noise, and a switchable 10 dB pad enables distortion-free recording of very loud sound sources associated with proximity miking. If no phantom power is available, the C1000 S can be powered by two standard AA batteries for up to 120 hours.
Featuring a pre-polarized design encased in a sturdy metal chassis, a gold-sputtered microphone capsule housing and gold-plated XLR pins, this microphone is well suited for mobile applications such as broadcast and interviews, even in high-humidity environments.
The C1000 S comes with a stand adapter, a foam windscreen and a microphone bag.
- Presence-boost adapter offers three discrete frequency settings to add clarity to speech and instrument sounds
- Polar-pattern converter allows microphone pattern to be switched from cardioid to hypercardioid
- Pre-polarized design, gold-sputtered microphone-capsule housing and gold-plated XLR pins make this microphone well suited for portable applications and high-humidity environments
- Switchable low-cut filter at 80 Hz to reduce rumble or wind noises which may cause distortion at low frequencies.
- Switchable 10 dB pad to enable distortion-free recording of very loud sound sources in proximity miking
- If no phantom power is available, the C1000 S can be powered by two standard AA batteries for up to 120 hours
- Sturdy metal chassis and specialized mic clip to keep microphone securely attached to stands
General |
Audio Frequency bandwidth |
50 to 20000 Hz |
Sensitivity |
6 mV/Pa |
Equivalent Noise Level |
21 dB-A |
Signal to Noise |
73 dB-A |
Preattunation Pad |
10 dB |
Bass Cut Filter |
80 Hz |
Electrical Impedance |
200 Ohms |
Recommended Load Impedance |
2000 Ohms |
|
Polar Patterns |
Polar Pattern |
hypercardioid; cardioid |
Number |
2 |
|
Powering Interface |
Voltage |
9 to 52 V |
Current |
3 mA |
|
Audio Output |
Type |
Balanced XLR |
Gender |
Male |
Contacts |
3-pin |
|
Design |
Body |
metal |
Finish |
matte grayish blue |
|
Dimensions / Weight |
Length |
229 mm |
Height |
34 mm |
Diameter |
34 mm |
Net Weight |
320 g |
|
|
The e 914 is a high grade condenser microphone for very demanding applications.
Its outstanding sound properties qualify the e 914 for highly sophisticated tasks.
The e 914 is a perfect microphone for ambitious recordings and live performances.
Its main areas of application are acoustic guitars, cymbals, percussion, overhead,
orchestras, grand pianos etc .
Features
Exceptionally lively, clear sound
Three-position sensitivity switch
Three-position bass roll-off/cut-off switch
Very high sound pressure handling capability
Exchangeable microphone capsule
Delivery Includes
e 914 microphone
Microphone clamp
Windscreen
Pouch
User manual
Technical Data
Pick-up pattern cardioid
Frequency response 20...20 000 Hz
Sensitivity in free field, no load (1kHz) 7 mV/Pa
Equivalent noise level 19 dB(A)
Attenuation 0, -10, -20 dB
Max. Sound pressure level (aktiv) 137, 147, 157 dB
Nominal impedance 100 Ohm
Min. terminating impedance 1000 Ohm
Dimensions 24 x 157 mm
Weight 198 g
| The NT5 matched pairs are a masterpiece of small-diaphragm cardioid-
condenser microphone design.Intended for recording acoustic instruments,
drum overheads, cymbals and live performances, the compact externally
polarized mic employs a .5? capsule, an active J-FET impedance converter
with bipolar output buffer.
Finished in durable satin nickel, the NT5 is intended for either single or stereo
X/Y mic set-ups. The NT5 matched pairs comesupplied in a custom carry case
with windshields and mounts.
SPECIFICATIONS:
Acoustic principle: Externally polarised single diaphragm
Directional pattern: Cardioid
Frequency range: 20Hz - 20kHz
Output impedance: 100?
Signal noise ratio din iec 651: 78dB
Equvalent noise: Maximum spl: 143 dB @ 1% THD into 1k_
Sensitivity:
-38 dB re 1v/Pa ± 2 dB equivalent to 12mV/Pa where 1 Pa = 94dBSPL
Power supply voltage: P48 Supply (38V?52V), P24 Supply (20V-26V)
Current consumption: 4 mA, 2 mA,
Weight: 100g | Technical specifications
Polar pattern |
cardioid |
Frequency range |
50 to 20,000 Hz |
Sensitivity |
20 mV/Pa (?34 dBV) |
Max. SPL |
125 dB (k=1 %) |
Equivalent noise level |
21 dB-A |
Signal/noise ratio (A-weighted) |
73 dB |
Impedance |
600 ohms |
Recommended load impedance |
>2000 ohms |
Supply voltage |
9 to 52 V phantom power, requires DPA adapter (supplied with most Installation Modules) |
Current consumption |
|
Connector |
Discreet Acoustics Modular standard |
Finish |
matte dark gray |
Dimensions |
13.5 x 20 mm dia. (0.5 dia. x 0.8 in.) |
Net weight |
5 g (0.17 oz.) |
Shipping weight |
88 g (3.1 oz.) |
Accessories (included) |
W 30 |
|
The ME 66 is a shot gun microphone head designed for use with the K6 and K6P powering modules. It is especially suitable for reporting, film and broadcast location applications and for picking up quiet signals in noisy or acoustically live environments as it discriminates against sound not emanating from the main pick-up direction. Matt black, anodised, scratch-resistant finish.
Pick-up pattern : super-cardioid/lobar
Sensitivity in free field, no load (1kHz) : 50 mV/Pa +- 2,5 dB
Nominal impedance : 200 Ohm (K6)
Min. terminating impedance : 1000 Ohm ( K6)
Equivalent noise level : 10 dB
Dimensions : d 22,5 x 221 mm
Weight : 65 g
| NT3 - Versatile & Dependable
Stylish and modern, the NT3 is a studio and location workhorse. With both
48V phantom and internal 9V battery operation, this R?DE is at home anywhere.
Intended for studio, stage and location work, this versatile handheld or stand
mounted microphone incorporates a true externally polarized condenser (hyper-
cardioid polar response) transducer with an internal capsule shock mounting
system, and an ultra-low noise electronic circuit that has a high immunity to R.F.
interference. Incorporating a rugged welded and heat-treated mesh head and all
metal body. The NT3 is supplied in a zip pouch with a windshield, stand mount
and thread adaptor.
SPECIFICATIONS:
Acoustic principle: Externally polarised 19mm (3/4“) condenser
Directional pattern: Hypercardioid
Frequency range: 20Hz-20 kHz
Output impedance: 200?
Signal noise ratio din iec 651: > 77dB (per IEC268-15)
Equvalent noise: 123dB (per IEC268-15)
Power supply voltage: P48, P24, P12 phantom 9V battery
Weight without battery: 371g
Weight with battery: 680g |
Reviews
There are no reviews yet.