Content | The A-1700 Series of high-performance mixing-dedicated power amplifiers are ideal for PA applications that value versatility. Specifically designed to satisfy the multi-microphone public address requirements of environments such as places of worship and meeting halls, the A-1700 Series Microphone Mixing Amplifiers focus on operational flexibility as well as advanced functions, proving an ideal cost-effective PA solution.
Specification |
|
Power Source |
AC mains 50/60Hz) |
Output |
240W |
Power Consumption |
532W (rated output), 220W (EN60065) |
Frequency Response |
50 - 20,000Hz ±3dB |
Distortion |
Under 2% at 1kHz, rated power |
Input |
MIC 1 - 6: -60dB*, 600Ω, electronically-balanced, combined type of XLR-3-31 equivalent and phone jack
AUX 1 - 2: -20dB*, 600Ω, electronically-balanced, combined type of XLR-3-31 equivalent and phone jack
(Either MIC 5 or AUX 1, and either MIC 6 or AUX 2 selectable)
AUX 3 - 4: -20dB*, 10kΩ, unbalanced, RCA pin jack
AUX 5: -20dB*, 10kΩ, unbalanced, combined type of XLR-3-31 equivalent and phone jack
PWR AMP IN: 0dB*, 600Ω, unbalanced, RCA pin jack
An equalizer or other signal processor connectable between LINE OUT and PWR AMP IN terminals) |
Output |
REC: 0dB*, 600Ω, unbalanced, RCA pin jack
LINE: 0dB*, 600Ω, unbalanced, RCA pin jack
SPEAKER SELECTOR: 2 zone, high impedance
(100V line/42Ω), individual selector key, M4 screw terminal
DIRECT SPEAKER OUT:
High impedance (100V line/42Ω),M4 screw terminal
Low impedance (4 - 16Ω), M4 screw terminal
(Both Low and High impedance terminals cannot be used at the same time.) |
Phantom Power |
ON or OFF for each MIC 1 - 6 with switch setting |
S/N ratio
(Band Pass: 20 - 20,000Hz) |
Over 100dB (Master volume: min)
Over 76dB (Master volume: max)
Over 60dB (MIC 1 - 4))
Over 53dB (MIC 5, 6)
Over 76dB (AUX 1 - 5) |
Tone Control |
Bass: ±10dB at 100Hz, Treble: ±10dB at 10kHz |
Control Input |
REMOTE VOLUME: M3 screw terminal
POWER REMOTE: No-voltage make contact input, open voltage: 24V DC (when the unit's power is OFF), short-circuit: under 10mA, M3 screw terminal |
Indicator |
5 point LED output level meter,
Power indicator LED,
Zone indicator LED |
Operating Temperature |
-10ºC - +40ºC |
Finish |
Panel: ABS resin, black, hair line
Case: Steel plate, black |
Dimensions |
420 (W) x 107.7 (H) x 367 (D)mm |
Weight |
13.5kg |
Accessory |
Power cord x 1,
Terminal block cover x 1,
Terminal block cover mounting screw x 2 |
Option |
Rack mounting bracket: MB-25B,
Volume control cover: YA-920. |
|
Note* Note: Distance between barriers on the above screw terminals; M3 = 7mm, M4 = 9mm |
|
* 0dB = 1V |
| - Easy installation in practically any 12V battery equipped car.
- Compact, rugged construction and front panel controls.
- Two phone jack mic. inputs and handy phone jack AUX input for external equipment connection.
- Unidirectional dynamic microphone with talk switch.
Specification |
| Power Source | Standard voltage: 14VDC
Usable Voltage; 10 ~ 16V DC (12V Battery Used) | Power Consumption | 2.2A or less at rated power output. | Output Power | Rated 15W, max. 35W | Output Impedance | 4Ω (BRN), 8Ω (ORG), COmmon (WHT)
Changeable by changing lead wire connections. | Distortion | Less than 5% (at 1kHz rated output) | Frequency Response | 100 ~ 10,000Hz | Input | Mic 1, 2 : 600Ω, 4 mV, Phone Jack
Aux : 10 kΩ, 500 mV, Phone Jack | Dimensions | (W x H x D): 178 x 50 x 132mm (mounting device excluded) | Weight | 900g | Finish | Front panel; ABS resin, Black
Case; Zinc plated steel sheet | Accessory | Microphone holder ... 1
Mounting Bracket ... 1
Mounting Screw ... 1
Fuse (4A) ... 1
Connection cord ... 1 set | Accessory | Microphone Unidirectional dynamic type with Talk switch
Impedance : 600Ω
Sensitivity : -53dB (IkHz, 0 dB = 1 V / Pa) |
|
XB Series - Intelligent Power
Power Without Compromises. The XV is designed for paging, music and alarm signals. Versatile, dynamic and extremely rugged according to IEC286-3. For the highest requirements in safety and quality. Sequential power on, alive contacts and incorporated ground fault detection - the XV is the solution under all conditions. Without the need for additional equipment. For uninterrupted and troublefree operation. Needless to say that the Bittner High-End toroidal output transformers in the XV series are some of the best available.
High Tech SMT Design Protection Circuits: DC, LF, HF, Thermal, Short Circuit, Current Limiter, 3 ms Muting Delay PHOENIX High-End Toroidal Output 100V Transformers Ground Fault Detection LED Indicators for POWER, SIGNAL, CLIP, PROTECT, GNDFAULT Temperature controlled, variable speed low noise fans Volume Controls at the back Stereo / Bridged / Parallel Mode Softstart Sequential Remote Power On Alive Contact Ground Lift 3 Years Warranty
TECHNICAL DATA: XV 200: 2x 100 W / 100 V Class: AB Frequency Response: 20 Hz - 20 kHz (0 / -0.3 dB) THD: < 0.07% Signal-to-Noise Ratio: < 101 dB Channel Seperation: > 70 dB Input Sensitivity: +6 dBu Input Clipping: 22 dBu Input Impedance: 20 kOhm Cooling: 2 to 3 fans (temp. reg. variable speed) Weight: 15 kg Dimensions: 2 RU / 483 x 88 x 382 mm (19" x 3.5" x 15“)
|
XB Series - Intelligent Power
Power Without Compromises. The XV is designed for paging, music and alarm signals. Versatile, dynamic and extremely rugged according to IEC286-3. For the highest requirements in safety and quality. Sequential power on, alive contacts and incorporated ground fault detection - the XV is the solution under all conditions. Without the need for additional equipment. For uninterrupted and troublefree operation. Needless to say that the Bittner High-End toroidal output transformers in the XV series are some of the best available.
High Tech SMT Design Protection Circuits: DC, LF, HF, Thermal, Short Circuit, Current Limiter, 3 ms Muting Delay PHOENIX High-End Toroidal Output 100V Transformers Ground Fault Detection LED Indicators for POWER, SIGNAL, CLIP, PROTECT, GNDFAULT Temperature controlled, variable speed low noise fans Volume Controls at the back Stereo / Bridged / Parallel Mode Softstart Sequential Remote Power On Alive Contact Ground Lift 3 Years Warranty
TECHNICAL DATA: XV 600: 2x 300 W / 100 V Class: AB Frequency Response: 20 Hz - 20 kHz (0 / -0.3 dB) THD: < 0.07% Signal-to-Noise Ratio: < 101 dB Channel Seperation: > 70 dB Input Sensitivity: +6 dBu Input Clipping: 22 dBu Input Impedance: 20 kOhm Cooling: 2 to 3 fans (temp. reg. variable speed) Weight: 19 kg Dimensions: 2 RU / 483 x 88 x 382 mm (19" x 3.5" x 15“)
|
High cost-performance
Suitable for commercial audio systems in schools,
offices, shops, restaurants, factories, houses of worship, and large meeting rooms.
Equipped with balanced mic. inputs for better isolation from external noise, compared to unbalanced inputs.
Improved durability compared with conventional
TOA models.
Flexibility
A wide range of power outputs from 30W to 240W
Offers a comfortable acoustic space thanks to tone
control at bass and treble.
Both AC and DC operation possible
Phantom power provided to MIC1, for supplying
power to a condenser microphone.
Easy to handle
Scratch and fingerprint-resistant finish•Easy and quick volume control with master volume control.
Specification |
| Power Source | 220 - 240V AC or 24V DC | Rated Output | 120W | Power Consumption | 124W (EN60065), 260W(AC operation at rated output, 8A (DC operation at rated output) | Frequency Response | 50 - 20,000Hz (+/- 3 dB) | Distortion | Under 1% at 1kHz,1/3 rated power | Input | MIC 1: -60db 600Ω,electronically balanced, 5-P Din type. MIC 2,3:-60db 600Ω,electronically balanced, 5-P phone jack. AUX 1,2: -20dB, 10kΩ, unblanced, RCA pin jack. Mute: Contact Pin 4 - 5 Closure input (for MIC 1) | Output | SPEAKER OUT:Balanced (floating)
HIGH IMPEDANCE:83W (100V)
LOW IMPEDANCE: 4Ω (22V)
REC. OUT: Odb, 600Ω unbalanced, RCA pin jack | Phnatom Powe | DC + 21V (MIC 1) | S/N Ratio | Over 60dB | Tone Control | Bass: +/- 10 dB at 100k Hz Treble: +/- 10 dB at 10k Hz | Muting | MIC1: Mutes other signals by 0 - 30 dB attenuation | Indicator | Power signal, peak | Finish | Panel: ABS resin, black/Case: Steel plate, black | Dimensions | 420 (W) x 100.9 (H) x 360.3 (D) mm | Weight | 10kg |
|
- Easy installation in practically any 12V battery equipped car.
- Compact, rugged construction and front panel controls.
- Two phone jack mic. inputs and handy phone jack AUX input for external equipment connection.
- Unidirectional dynamic microphone with talk switch.
Specification |
| Power Source | Standard voltage: 14VDC
Usable Voltage; 10 ~ 16V DC (12V Battery Used) | Power Consumption | 9A or less at rated power output. | Output Power | Rated 60W, max. 120W | Output Impedance | 4Ω (BRN), 8Ω (ORG), COmmon (WHT)
Changeable by changing lead wire connections. | Distortion | Less than 5% (at 1kHz rated output) | Frequency Response | 100 ~ 10,000Hz | Input | Mic 1, 2 : 600Ω, 4 mV, Phone Jack
Aux : 10 kΩ, 500 mV, Phone Jack | Dimensions | (W x H x D): 178 x 50 x 170mm (mounting device excluded) | Weight | 1.2 kg | Finish | Front panel; ABS resin, Black
Case; Zinc plated steel sheet | Accessory | Microphone holder ... 1
Mounting Bracket ... 1
Mounting Screw ... 1
Fuse (12A) ... 1
Connection cord ... 1 set | Accessory | Microphone Unidirectional dynamic type with Talk switch
Impedance : 600Ω
Sensitivity : -53dB (IkHz, 0 dB = 1 V / Pa) |
|
Reviews
There are no reviews yet.