TOA A-1724 Mixer Amplifier 240W/100V

Discontinued

539.00 incl. GR VAT

Out of stock

CompareAdd to wishlist Submit Better Price
The A-1700 Series of high-performance mixing-dedicated power amplifiers are ideal for PA applications that value versatility. Specifically designed to satisfy the multi-microphone public address requirements of environments such as places of worship and meeting halls, the A-1700 Series Microphone Mixing Amplifiers focus on operational flexibility as well as advanced functions, proving an ideal cost-effective PA […]

 

Read more

The A-1700 Series of high-performance mixing-dedicated power amplifiers are ideal for PA applications that value versatility. Specifically designed to satisfy the multi-microphone public address requirements of environments such as places of worship and meeting halls, the A-1700 Series Microphone Mixing Amplifiers focus on operational flexibility as well as advanced functions, proving an ideal cost-effective PA solution.
Specification
Power Source AC mains 50/60Hz)
Output 240W
Power Consumption 532W (rated output), 220W (EN60065)
Frequency Response 50 – 20,000Hz ±3dB
Distortion Under 2% at 1kHz, rated power
Input MIC 1 – 6: -60dB*, 600Ω, electronically-balanced, combined type of XLR-3-31 equivalent and phone jack
AUX 1 – 2: -20dB*, 600Ω, electronically-balanced, combined type of XLR-3-31 equivalent and phone jack
(Either MIC 5 or AUX 1, and either MIC 6 or AUX 2 selectable)
AUX 3 – 4: -20dB*, 10kΩ, unbalanced, RCA pin jack
AUX 5: -20dB*, 10kΩ, unbalanced, combined type of XLR-3-31 equivalent and phone jack
PWR AMP IN: 0dB*, 600Ω, unbalanced, RCA pin jack
An equalizer or other signal processor connectable between LINE OUT and PWR AMP IN terminals)
Output REC: 0dB*, 600Ω, unbalanced, RCA pin jack
LINE: 0dB*, 600Ω, unbalanced, RCA pin jack
SPEAKER SELECTOR: 2 zone, high impedance
(100V line/42Ω), individual selector key, M4 screw terminal
DIRECT SPEAKER OUT:
High impedance (100V line/42Ω),M4 screw terminal
Low impedance (4 – 16Ω), M4 screw terminal
(Both Low and High impedance terminals cannot be used at the same time.)
Phantom Power ON or OFF for each MIC 1 – 6 with switch setting
S/N ratio
(Band Pass: 20 – 20,000Hz)
Over 100dB (Master volume: min)
Over 76dB (Master volume: max)
Over 60dB (MIC 1 – 4))
Over 53dB (MIC 5, 6)
Over 76dB (AUX 1 – 5)
Tone Control Bass: ±10dB at 100Hz, Treble: ±10dB at 10kHz
Control Input REMOTE VOLUME: M3 screw terminal
POWER REMOTE: No-voltage make contact input, open voltage: 24V DC (when the unit’s power is OFF), short-circuit: under 10mA, M3 screw terminal
Indicator 5 point LED output level meter,
Power indicator LED,
Zone indicator LED
Operating Temperature -10ºC – +40ºC
Finish Panel: ABS resin, black, hair line
Case: Steel plate, black
Dimensions 420 (W) x 107.7 (H) x 367 (D)mm
Weight 13.5kg
Accessory Power cord x 1,
Terminal block cover x 1,
Terminal block cover mounting screw x 2
Option Rack mounting bracket: MB-25B,
Volume control cover: YA-920.
Note* Note: Distance between barriers on the above screw terminals; M3 = 7mm, M4 = 9mm
* 0dB = 1V
Weight 13.50 kg

Reviews

There are no reviews yet.

Be the first to review “TOA A-1724 Mixer Amplifier 240W/100V”

Your email address will not be published. Required fields are marked *

Quick Comparison

TOA A-1724 Mixer Amplifier 240W/100V removeBITTNER AUDIO XV 200-2x100W-100V POWER AMPLIFIER removeBITTNER AUDIO XV400-2x200W-100V POWER AMPLIFIER removeCrown CDI-1000 2x700W-4Ω Power Amplifier removeCROWN 160MA 60-Watt Mixer Amplifier removeTOA VP-200VX-BGM Input & BGM Module for VX-2000 Series remove
NameTOA A-1724 Mixer Amplifier 240W/100V removeBITTNER AUDIO XV 200-2x100W-100V POWER AMPLIFIER removeBITTNER AUDIO XV400-2x200W-100V POWER AMPLIFIER removeCrown CDI-1000 2x700W-4Ω Power Amplifier removeCROWN 160MA 60-Watt Mixer Amplifier removeTOA VP-200VX-BGM Input & BGM Module for VX-2000 Series remove
Image
SKUA-1724XV200XV400CDI-1000160MAVP200VX-BGM
Rating
Price 539.00 incl. GR VAT 727.87 incl. GR VAT 892.79 incl. GR VAT 1,235.00 incl. GR VAT 481.00 incl. GR VAT 83.81 incl. GR VAT
Stock

Out of stock

Available on backorder

Available on backorder

Available on backorder

Available on backorder

Available on backorder

AvailabilityOut of stockAvailable on backorderAvailable on backorderAvailable on backorderAvailable on backorderAvailable on backorder
Add to cart

Read more

Add to cart

Add to cart

Add to cart

Add to cart

Add to cart

Description
ContentThe A-1700 Series of high-performance mixing-dedicated power amplifiers are ideal for PA applications that value versatility. Specifically designed to satisfy the multi-microphone public address requirements of environments such as places of worship and meeting halls, the A-1700 Series Microphone Mixing Amplifiers focus on operational flexibility as well as advanced functions, proving an ideal cost-effective PA solution.
Specification
Power Source AC mains 50/60Hz)
Output 240W
Power Consumption 532W (rated output), 220W (EN60065)
Frequency Response 50 - 20,000Hz ±3dB
Distortion Under 2% at 1kHz, rated power
Input MIC 1 - 6: -60dB*, 600Ω, electronically-balanced, combined type of XLR-3-31 equivalent and phone jack AUX 1 - 2: -20dB*, 600Ω, electronically-balanced, combined type of XLR-3-31 equivalent and phone jack (Either MIC 5 or AUX 1, and either MIC 6 or AUX 2 selectable) AUX 3 - 4: -20dB*, 10kΩ, unbalanced, RCA pin jack AUX 5: -20dB*, 10kΩ, unbalanced, combined type of XLR-3-31 equivalent and phone jack PWR AMP IN: 0dB*, 600Ω, unbalanced, RCA pin jack An equalizer or other signal processor connectable between LINE OUT and PWR AMP IN terminals)
Output REC: 0dB*, 600Ω, unbalanced, RCA pin jack LINE: 0dB*, 600Ω, unbalanced, RCA pin jack SPEAKER SELECTOR: 2 zone, high impedance (100V line/42Ω), individual selector key, M4 screw terminal DIRECT SPEAKER OUT: High impedance (100V line/42Ω),M4 screw terminal Low impedance (4 - 16Ω), M4 screw terminal (Both Low and High impedance terminals cannot be used at the same time.)
Phantom Power ON or OFF for each MIC 1 - 6 with switch setting
S/N ratio (Band Pass: 20 - 20,000Hz) Over 100dB (Master volume: min) Over 76dB (Master volume: max) Over 60dB (MIC 1 - 4)) Over 53dB (MIC 5, 6) Over 76dB (AUX 1 - 5)
Tone Control Bass: ±10dB at 100Hz, Treble: ±10dB at 10kHz
Control Input REMOTE VOLUME: M3 screw terminal POWER REMOTE: No-voltage make contact input, open voltage: 24V DC (when the unit's power is OFF), short-circuit: under 10mA, M3 screw terminal
Indicator 5 point LED output level meter, Power indicator LED, Zone indicator LED
Operating Temperature -10ºC - +40ºC
Finish Panel: ABS resin, black, hair line Case: Steel plate, black
Dimensions 420 (W) x 107.7 (H) x 367 (D)mm
Weight 13.5kg
Accessory Power cord x 1, Terminal block cover x 1, Terminal block cover mounting screw x 2
Option Rack mounting bracket: MB-25B, Volume control cover: YA-920.
Note* Note: Distance between barriers on the above screw terminals; M3 = 7mm, M4 = 9mm
* 0dB = 1V

XB Series - Intelligent Power

Power Without Compromises.
The XV is designed for paging, music and alarm signals. Versatile, dynamic and
extremely rugged according to IEC286-3. For the highest requirements in safety
and quality.
Sequential power on, alive contacts and incorporated ground fault detection -
the XV is the solution under all conditions. Without the need for additional equipment.
For uninterrupted and troublefree operation.
Needless to say that the Bittner High-End toroidal output transformers in the XV
series are some of the best available.

High Tech SMT Design
Protection Circuits: DC, LF, HF, Thermal, Short Circuit, Current Limiter, 3 ms Muting Delay
PHOENIX
High-End Toroidal Output 100V Transformers
Ground Fault Detection
LED Indicators for POWER, SIGNAL, CLIP, PROTECT, GNDFAULT
Temperature controlled, variable speed low noise fans
Volume Controls at the back
Stereo / Bridged / Parallel Mode
Softstart
Sequential Remote Power On
Alive Contact
Ground Lift
3 Years Warranty

TECHNICAL DATA:
XV 200:  2x 100 W / 100 V
Class:  AB
Frequency Response: 20 Hz - 20 kHz (0 / -0.3 dB)
THD:  < 0.07%
Signal-to-Noise Ratio:  < 101 dB
Channel Seperation:  > 70 dB
Input Sensitivity:  +6 dBu
Input Clipping:  22 dBu
Input Impedance:  20 kOhm
Cooling:  2 to 3 fans (temp. reg. variable speed)
Weight:  15 kg
Dimensions:  2 RU / 483 x 88 x 382 mm (19" x 3.5" x 15“)

 

XB Series - Intelligent Power

Power Without Compromises.
The XV is designed for paging, music and alarm signals. Versatile, dynamic and
extremely rugged according to IEC286-3. For the highest requirements in safety
and quality.
Sequential power on, alive contacts and incorporated ground fault detection -
the XV is the solution under all conditions. Without the need for additional equipment.
For uninterrupted and troublefree operation.
Needless to say that the Bittner High-End toroidal output transformers in the XV
series are some of the best available.

High Tech SMT Design
Protection Circuits: DC, LF, HF, Thermal, Short Circuit, Current Limiter, 3 ms Muting Delay
PHOENIX
High-End Toroidal Output 100V Transformers
Ground Fault Detection
LED Indicators for POWER, SIGNAL, CLIP, PROTECT, GNDFAULT
Temperature controlled, variable speed low noise fans
Volume Controls at the back
Stereo / Bridged / Parallel Mode
Softstart
Sequential Remote Power On
Alive Contact
Ground Lift
3 Years Warranty

TECHNICAL DATA:
XV 400:  2x 200 W / 100 V
Class:  AB
Frequency Response: 20 Hz - 20 kHz (0 / -0.3 dB)
THD:  < 0.07%
Signal-to-Noise Ratio:  < 101 dB
Channel Seperation:  > 70 dB
Input Sensitivity:  +6 dBu
Input Clipping:  22 dBu
Input Impedance:  20 kOhm
Cooling:  2 to 3 fans (temp. reg. variable speed)
Weight:  17 kg
Dimensions:  2 RU / 483 x 88 x 382 mm (19" x 3.5" x 15“)

Crown CDi 1000 2x700W-4Ω Power Amplifier

The Crown? CDi 1000 power amplifi er shall be a solid-state two-channel model
with a switch-mode universal power supply.
The outputs shall be usable as dual or bridged-mono modes of operation.
The bridged-mono mode shall bridge the outputs to provide increased output
voltage.
Front panel controls and indicators shall include the following:
Level: Detented rotary level control, one per channel.
Power Switch: On/off switch applies AC power to the amplifi er.
Sel/Prev/Next Buttons: Three buttons near the LCD screen shall be used to
access menu items and front panel lockout.
LCD Screen: Backlit liquid crystal display shows speaker presets and signal
processing.
Signal Indicator: Green LED, one per channel, illuminates when a very low-level
signal is present at input.
?10 Indicator: Green LED fl ashes when output signal exceeds ?10 dB below
clip.
?20 Indicator: Green LED fl ashes when output signal level exceeds ?20 dB
below clip.
Ready Indicator: Green LED, one per channel, illuminates when the amplifi er is
ready to produce audio.
Clip Indicator: Red LED, one per channel, turns on at the threshold of audible
distortion.
Temp Indicator: Red LED, one per channel, illuminates under excessive temperature
conditions.
Power Indicator: Blue LED illuminates when the amplifi er has been turned on
and has power.
Rear panel controls and connectors shall include the following:
AC Line Connector: NEMA 5-15P (15A).
Input Connector: Two 3-pin removable Phoenix-type connectors each accept a
balanced line-level input signal.
Output Connectors: 4-position barrier strip with connectors for dual louspeakers
or bridge-mono loudspeaker. Dual connectors shall work with 2-8 ohm or
70V loads. Bridge-mono connectors shall work with 4-8 ohm or 140V loads.
HiQnet USB Connector: Type B, connects to a USB port on a PC.
The amplifi er shall have the following specifi cations:
Output Power: 2 ohm Dual (per channel): 700W with 1% THD, 4 ohm Dual (per
channel): 500W, 8 ohm Dual (per channel) 275W, 4 ohm Bridge-Mono: 1,400W
with 1% THD, 8 ohm Bridge-Mono: 1,000W, 70V Dual (per channel): 500W.
Voltage Gain at 1kHz, 8 ohm rated output: 30.5 dB.
Frequency Response: +0/?1 dB from 20 Hz to 20 kHz at 1 watt into 4 ohms.
Load Impedance: Safe with all types of loads. Rated for 2 to 8 ohms in Stereo
mode, 4 to 16 ohms in Bridge-Mono mode.
Sensitivity: 1.4V.
Signal to Noise Ratio (below rated 8-ohm power at 1 kHz): 100 dB
(A weighted).
Damping Factor: Better than 500 from 20 Hz to 400 Hz.
Crosstalk: > 70 dB below rated power, 20 Hz to 1 kHz.
Input Stage: Input is electronically balanced and employs precision 1% resistors.
Input Impedance (nominal): 20 k ohms, balanced;10 k ohms, unbalanced.
Maximum Input Signal: +22 dBu typical.
AC Line Voltage and Frequency Confi gurations Available: 100V, 120V, 220-240V,
50/60 Hz.
AC Line Current: 6.5A.
At Idle: Draws no more than 90 watts.
Operating Temperature: 0° C to 40° C at 95% relative humidity (non-condensing).
The DSP section shall have the following specifi cations:
Input EQ: 6 parametric fi lters per channel with adjustable Q, ±15 dB boost/cut.
Also adjustable high and low shelving fi lters. This 8-fi lter EQ section can be
bypassed.
Crossover Filters: Highpass and lowpass per channel. Butterworth 6/12/18/24
dB per octave and Linkwitz-Riley 24/48 dB per octave. Also includes ±15 dB
bandpass gain and polarity control.
Output EQ: 8 parametric fi lters per channel with adjustable Q, ±15 dB boost/cut.
This 8-fi lter EQ section can NOT be bypassed. Filters are enabled individually.
Delay: Up to 50 msec total delay per channel.
Output Limiter: Prevents clipping and protects loudspeakers. Choice of ?3, ?6,
or ?12 dB threshold per channel.
Presets: 20 presets. 19 are user-definable.
Protection shall include the following:
CDi-Series amplifi ers shall be protected against shorted, open or mismatched
loads; overloaded power supplies; excessive temperature; chain destruction
phenomena; excessive output current, and input overload damage. They also
protect loudspeakers from input/output DC, large or dangerous DC offsets and
turn-on/turn-off transients
The chassis shall be steel. Cooling shall be by a proportional speed fan with
front-to-rear airfl ow.
Dimensions shall be EIA Standard 19-in. rack mount width (EIA RS-310-B), 3.5
in. (8.9 cm) high and 12.25 in. (31.11 cm) deep behind mounting surface.
Net weight shall be 19 lb (8.6 kg). Shipping weight shall be 22 lb (10.0 kg).
The amplifier shall be designated the Crown CDi 1000.

The Crown® 160MA is a high-value mixer-amplifier for commercial audio. It provides 8-ohm and constant-voltage outputs (70V and 100V). Typical uses are paging, background music, and music-on-hold. The 160MA provides 4 inputs (each with a volume control) and a 60W amplifier output. Other features include priority muting, voice activated muting, phantom power, and Bass and Treble controls.

FEATURES

  • 4 inputs (each with a volume control), and one 60W amplifier output channel
  • Ideal for paging, background music, and music-on-hold
  • Balanced Phoenix-type mic/line input, telephone output, dual RCA stereo music inputs, screw-terminal speaker outputs
  • Priority muting by VOX or external switch
  • Bass and Treble controls on master output
  • Three-Year, No-Fault, Fully Transferable
  • Warranty completely protects your investment and guarantees its specifications

The VP-200VX Power Amplifier Input Module is designed to be used in conjunction with theVP-2064, VP-2122, VP-2241 or VP-2421 power amplifier.

Weight13.50 kg15.00 kg17.00 kg10.00 kg3.70 kg0.50 kg
DimensionsN/AN/AN/AN/AN/AN/A
Additional information
Weight 13.50 kg
Weight 15.00 kg
Weight 17.00 kg
Weight 10.00 kg
Weight 3.70 kg
Weight 0.50 kg