Content |
Stereo Mode Ratings (Both Channels Driven):
8 ohms:
- FTC 20 Hz - 20kHz, 0.1% THD: 1050W
- EIA 1 kHz, 0.1% THD: 1100W
4 ohms:
- FTC 20 Hz - 20kHz, 0.1% THD: 1600W
- EIA 1 kHz, 0.5% THD: 2000W (1% THD)
2 ohms:
- EIA 1 kHz, 1% THD: 2500W
70V Direct Drive:
- EIA 1 kHz, 1% THD: 2500W
100V Direct Drive:
- EIA 1 kHz, 1% THD: 1000W
Bridged Mono Mode Ratings/Specifications:
8 ohms:
- FTC 20 Hz - 20kHz, 0.1% THD: 3200W
- EIA 1 kHz, 0.1% THD: 3600W
4 ohms:
- EIA 1 kHz, 1% THD: 5000W
70V Direct Drive:
- EIA 1 kHz, 1% THD: 5000W
100V Direct Drive:
- EIA 1 kHz, 1% THD: 3600W
Signal to Noise, 20Hz-20kHz, 0.1% THD, 8 Ohms: > -100dB
Input Sensitivity @ 8 Ohms: 1.42V (+5.3 dBu)
Voltage Gain @ 8 Ohms: 64x (36 dB)
Output Circuitry: 3-tier Class H
Power Requirements (120V):
- 1/8 power pink noise at 4 ohms: 13.9A
- 1/3 power pink noise at 4 ohms: 26.9A
Power Requirements (230V):
- 1/8 power pink noise at 4 ohms: 7A
- 1/3 power pink noise at 4 ohms: 13.5A
Distortion (SMPTE-IM): |
Number of Channels: 2
Output Power: (per channel)
8 ohms 1000W
4 ohms 1850W
2 ohms N/A
Output Power: (bridged)
8 ohms 3700W
4 ohms N/A
THD%: (@1dB below max output)
@ 1kHz |
Power Rating
Stereo Mode:
8Ω EIA 1 kHz 1% THD - 1500W
4Ω EIA 1 kHz 1% THD - 2500W
2Ω EIA 1 kHz 1% THD - 4000W
Bridged Mono:
8Ω EIA 1 kHz 1% THD - 5000W
4Ω EIA 1 kHz 1% THD - 8000W
Damping Factor Not Specified By Manufacturer
Input Sensitivity 26dB Setting - 5.27V
32dB Setting - 2.67V
Input Impedance > 10kΩ balanced, or unbalanced
Gain 39.1dB
Frequency Response 20Hz to 20kHz, +/- 0.2dB
Signal-to-Noise Ratio -104dB
Total Harmonic Distortion (THD) 0.1% @ 2Ω
0.03-0.06% @ 4Ω
0.01-0.03% @ 8Ω
Input Connections Input: XLR Male, XLR Female and 3-pin detachable terminal blocks (1 each per channel)
DataPort: HD-15, input signal in parallel with XLR input connectors
Output Connectors Output: Neutrik Speakon (ch 1 wired to both channels) and 5-way binding posts
Controls Front Panel AC Power Switch
Gain Controls, 21 detents, 1 dB steps (each channel)
Controls (Rear) Input Mode: Bridge (Yellow), Stereo (Green), or Parallel (Orange)
Gain / Sensitivity: 26dB (Orange), 32dB (Green), or 1.2V (Yellow)
High Pass (each channel): 3Hz (Off), 30Hz (Yellow), or 50Hz (Orange)
Clip Limiter (each channel): Off, On (Yellow)
Indicators Clip Limiter (each channel): Off, On (Yellow)
Camera Resolution Flow-thru air path and solid aluminum heat sinks
Power Consumption 120V 50/60Hz - 18A
230V 50Hz - 11A
Power Requirements Not Specified By Manufacturer
Dimensions (WxHxD) 19 x 3.5 x 15.63" (48.3 x 8.9 x 39.7cm)
Weight 33.5 lbs (15.2kg)
Specialties Parallel Dataport, XLR/M and XLR/F connectors for simple loop-through connectivity
|
Power supply
- Powersoft legendary universal switch-mode power supply up to 400VAC tolerant with Power Factor Correction
- Patented output filter with ripple cancellation network
- Low Inrush Limiting reduces AC inrush current, removing the need for expensive power sequencers
- Detachable AC mains cable with IEC C19/22.2 (16A for EU, 20 A for USA) socket
Protections
Fully protected circuit design with:
- Ac protection: shut down power supply when AC mains voltage is outside the operating range
- Clip limiter: prevents severely clipped waveforms from reaching loudspeakers, while still maintaining full peak power output
- DC protection: protects against infrasonic signal at the outputs
- VHF protections: protects the loudspeakers against non-audible, strong, non-musical high-frequency signals
- Short circuit protection: protects the amplifier from short circuit or other stressful events for the output circuits with automatic protection reset
- Long term limiter: protects the loudspeaker against steady long term RMS (non-audio) signals, by reducing maximum output
- Thermal protection: output stages operating temperature up to 80 °C (176 °F)
- Temperature controlled continuous variable speed fan, front to back airflow
- Temperature forecast with LCD traced historical behavior
General
- Fixed frequency switchmode output stage for high grade sound accuracy
- Compact size – all models only 1 RU for reduced rack cost and space
- Light weight – for easier racking and shipping: 7 kg (15.4 lbs)
- Standard Phoenix connectors: analog audio outputs, aux supply, alarms and GPIO
- Remotely switchable double input (main and aux) per channel
Loudspeaker system configuration
- Direct drive either low impedance loads or 70V / 100V Hi-Z distributed lines
- Switchable 35Hz / 70Hz high pass filter per channel
- Mixed configuration with Lo-Z/Hi-Z systems possible
- Bridged mode low impedance per channel pair
Alarms and GPI/O
- NC/NO contacts per channel for alarm notifications
- Remote ON/OFF switch
- Remote VCA control per channel
Digital Signal Processing
- TI C6000 DSP platform
- AD/DA converter: dual 24bit @ 48 kHz Tandem® architecture
- Input/output independent equalizers per channel providing PEQ, raised cosine, shelving IIR filters as well as custom output FIR filters
- Delay up to 100 ms for time alignment
- Active DampingControl™ for cable compensation
- Peak, RMS voltage, RMS current, TruePower™ limiters
Remote Control & Monitoring
Via software:
- Control and diagnostics monitoring via ArmoníaPlus
- Dedicated WebApp
Via Hardware:
- Attenuation (from 0dB to 26dB)
- High-pass filters (35Hz, 70Hz)
- Lo-Z/Hi-Z/70V/100V output selection
- Adjustable gain (from 26dB to 35 dB)
General |
Output power per Channel |
Output power per Channel |
1000 W @ 2 Ω |
800 W @ 4 Ω |
800 W @ 8 Ω |
Bridge mode |
|
2000 W @ 4 Ω |
1600 W @ 8 Ω |
Max output voltage / current |
Max unclipped output voltage@8 Ω |
|
|
115 Vpeak |
Current |
|
|
45 Apeak |
AC main power |
Power supply |
Universal, regulated switch mode with PFC (Power Factor Correction) |
Nominal power requirement |
|
|
100-240 V ±10%, 50-60 Hz |
Operating voltage |
|
|
90 V – 264 V |
Power consumption / current draw |
Idle |
|
115 V: 23 W – 0.34 A |
230 V: 23.3 W – 0.21 A |
1/8 of max output power @ 4 Ω |
|
115 V: 267 W – 2.5 A |
230 V: 274 W – 1.5 A |
THERMAL |
Operating temperature range |
|
|
0° – 45° C – 32° – 113° F |
Thermal dissipation* |
Idle |
|
115 V: 78 BTU/h |
230 V: 79 BTU/h |
1/8 of max output power @ 4 Ω |
|
115 V: 229 BTU/h |
230 V: 251 BTU/h |
|
Manufacturer |
LAB GRUPPEN |
Warranty |
10 Years Gurantee |
Channels |
Dual Channel |
Resistance ohms |
8Ω / 4Ω |
Resistance ohms |
2Ω |
DSP |
Yes |
Power (8 ohms/Watt RMS) per channel |
600 |
Power (4 ohms/Watt RMS) per channel |
1200 |
Power (2 ohms/Watt RMS) per channel |
800 |
Weight (kg) |
6.2 |
|
Live performance DSP amplifier. Fully integrated professional speaker processing with FIR Drive technology . Market leading acoustic performance and rock solid reliability. True 2 ohm stability. Intuitive system control software, makes setup and control easy. Rated power: 2 Χ 3000 Watts/2Ω, 2 Χ 2500 Watts/2,6Ω, 2 Χ 1700 Watts/4Ω, 2 Χ 900 Watts/8Ω.
Manufacturer |
DYNACORD |
Application |
Portable PA |
Channels |
Dual Channel |
Resistance ohms |
8Ω / 4Ω, 2Ω |
DSP |
Yes |
Weight (kg) |
18,2 |
Power (8 ohms/Watt RMS) per channel |
900 |
Power (4 ohms/Watt RMS) per channel |
1700 |
Power (2 ohms/Watt RMS) per channel |
3000 |
Series |
L series |
Model |
L3600FD |
Part Number |
F01U312397 |
Warranty |
3 Years Warranty |
|
Reviews
There are no reviews yet.