Content |
- Signal to Noise (20 Hz - 20 kHz): 100 dB - Input Sensitivity: 1.2 Vrms - Voltage Gain (8 Ohms): 34.4 dB - Output Circuitry: 2-tier Class H - Power Requirements: 6A - Frequency Response: 20 Hz - 20 kHz, +0, 1 dB - Dynamic Headroom (4 Ohms): 2 dB - Damping Factor: 100 - Input Impedance: Greater than 20k (balanced) - Maximum Input Level: +24 dB (16 Vrms) - Input Connectors (each channel): 3-pin XLR and 1/4-inch TRS, balanced, parallel Phono, unbalanced - Output Connectors (each channel): Speakon, 1/4-inch, Binding Posts - Amplifier and Load Protection: Short circuit, open circuit, thermal, RF protection Load protected against DC faults - Rear Panel Controls: Full Range / Crossover switch - Dimensions (H x W x D): 3.5 x 19 x 10.1 inches (89 mm x 483 mm x 257 mm) - Weight: 26 lbs (12 kg) Front Panel Controls and Indicators: - Gain controls, 21 detents - Red Clip LEDs, proportional, 0.1% THD threshold - Green Signal LEDs, threshold -35 dB - Blue Power LED, AC on Stereo Mode: - 8 Ohms / both channels driven: 500 Watts - 8 Ohms / single channel driven: 600 Watts - 4 Ohms / both channels driven: 700 Watts - 4 Ohms / single channel driven: 850 Watts Distortion: - 8 Ohms: less than 0.05% - 4 Ohms: less than 0.1% Dimensions and Weight in Packaging Shipping Weight: 31 lbs Shipping Dimensions: 24 x 15 x 7 in
|
A full model revision takes Yamaha's high-end PC-N power amplifiers to the next level - the PC-1N Series. The new PC-1N Series amplifiers feature an extraordinarily solid low end, rich midrange, and superbly defined highs. They also deliver fast response and exceptional stability even in the face of serious power supply limitations. Refinements throughout this expanded five-model lineup make these amplifiers the new benchmarks for quality, reliability, and versatility in professional applications. Frequency Response: 10 Hz – 40 KHz. Output Power: 2 x 500 Watt / 8Ω RMS, 2 x 800 Watt / 4Ω RMS, 1600 Watt / 8Ω bridge RMS. Weight: 12,5 Kg.
|
This professional stereo power amplifier, working in class-H mode, provides 2x800W, at an efficiency of around 85%.
A passive transformer based power supply and hand selected components makes this power rating possible with exceptional audio quality and absolute reliability, even in the 2 Ohm mode. The output stage is fully protected against over-temperature, short circuit, RFI and equipped with soft start circuit and temperature-controlled fan cooling. The integral soft clip limiter protects against damage to the connected loudspeakers. The activity of a protective circuit, signal and limiter is shown for each channel by LEDʼs.
AMPLIFIER SPECIFICATIONS |
---|
Power output stereo 2Ω: | 2 x 800 Watt rms | | Power output stereo 4Ω: | 2 x 650 Watt rms | | Power output stereo 8Ω: | 2 x 350 Watt rms | | Power output bridged 4Ω: | 1600 Watt rms | | Power output bridged 8Ω: | 1300 Watt rms | | Frequency Response: | 20 Hz ÷ 20 kHz | | Signal/noise rate: | > 103 dB | | Crosstalk: | > 70 dB | | Distortion (THD+N): | | | Intermodulation: | | | Damping factor: | 200:1 (8 Ω) | | Slew rate: | 50 V/μS | |
INPUT SECTION |
---|
Input connector: | 2 x XLR balanced, 6,3mm jack unbalanced | | Input sensitivity: | 0 / 0.775 dBm/V RMS | | Input impedance: | 20.000 kΩ | | Controls: | Volume control for each channel | |
OUTPUT SECTION |
---|
Output connector: | 2 x Neutrik Speakon 4 ways | |
SYSTEM PARAMETERS |
---|
Cooling: | Two-speed fan | | Protections: | Temperature, DC, RFI short circuit, Soft-Start, Thermal on transformer | |
POWER REQUIREMENT |
---|
Operating voltage: | 220÷240 / 110÷120 ~ 50 / 60 V ~ Hz | | Max.current: | 7.5 A | | Power Consumption: | 2700 W | |
PHYSICAL SPECIFICATIONS |
---|
Height: | 88 / 3.46 mm/inch | | Width: | 483 / 19.01 mm/inch | | Depth: | 455 / 17.91 mm/inch | | Net Weight: | 19.5 / 42.98 Kg/Lbs | |
SHIPPING INFORMATION |
---|
Package height: | 150 / 5.9 mm/inch | | Package width: | 555 / 21.85 mm/inch | | Package depth: | 525 / 20.66 mm/inch | | Shipping Weight: | 20 / 44.09 Kg/Lbs |
|
Crown DSi 2000 2x800W-4Ω Power Amplifier
The Crown? DSi 2000 power amplifier shall be a solid-state two-channel model with a switch-mode universal power supply. A rear-panel HD-15 connector shall provide input/output connectivity between the DSi amplifier and the DSi-8M System Monitor.
The outputs shall be usable as stereo or bridged-mono modes of operation.
The bridged-mono mode shall bridge the outputs to provide increased output voltage.
Front panel controls and indicators shall include the following:
Level: Detented rotary level control, one per channel.
Power Switch: On/off switch applies AC power to the amplifi er.
Sel/Prev/Next Buttons: Three buttons near the LCD screen shall be used to access menu items and front panel lockout.
LCD Screen: Backlit liquid crystal display shows speaker presets and signal processing.
Signal Indicator: Green LED, one per channel, illuminates when a very low-level signal is present at input.
?10 Indicator: Green LED fl ashes when output signal exceeds ?10 dB below clip.
?20 Indicator: Green LED fl ashes when output signal level exceeds ?20 dB below clip.
Ready Indicator: Green LED, one per channel, illuminates when the amplifier is ready to produce audio.
Clip Indicator: Red LED, one per channel, turns on at the threshold of audible distortion.
Temp Indicator: Red LED, one per channel, illuminates under excessive temperature conditions.
Power Indicator: Blue LED illuminates when the amplifi er has been turned on and has power.
Rear panel controls and connectors shall include the following:
AC Line Connector: NEMA 5-15P (15A).
Input Connector: Two 3-pin removable Phoenix-type connectors each accept a balanced line-level input signal.
Output Connectors: 4-position barrier strip with connectors for dual louspeakers or bridge-mono loudspeaker.
HiQnet USB Connector: Type B, connects to a HiQnet network.
HD-15 Connector: For cinema I/O compatibility with DSi-8M System Monitor.
The amplifier shall have the following specifications:
Output Power: 2 ohm Stereo (per channel): 1,000W with 1% THD, 4 ohm
Stereo (per channel): 800W with 0.5% THD, 8 ohm Stereo (per channel) 475W
with 0.5% THD, 4 ohm Bridge-Mono: 2,000W with 1% THD, 8 ohm Bridge-
Mono: 1,600W with 0.5% THD.
Voltage Gain at 1kHz, 8 ohm rated output: 26 dB.
Frequency Response: +0/?1 dB from 20 Hz to 20 kHz at 1 watt into 4 ohms.
Load Impedance: Safe with all types of loads. Rated for 2 to 8 ohms in Stereo
mode, 4 to 16 ohms in Bridge-Mono mode.
Sensitivity at 8 ohm rated output: 3.09V.
Sensitivity at 4 ohm rated output: 2.84V.
Sensitivity at 2 ohm rated output: 2.24V.
Signal to Noise Ratio (below rated 8-ohm power at 1 kHz): 105 dB
(A weighted).
Damping Factor: Better than 500 from 20 Hz to 500 Hz.
Crosstalk: > 70 dB below rated power, 20 Hz to 1 kHz.
Input Stage: Input is electronically balanced and employs precision 1% resistors.
Input Impedance (nominal): 20 k ohms, balanced;10 k ohms,unbalanced.
Maximum Input Signal: +22 dBu typical.
|
XR Series - Intelligent Power New Horizons.
A lightweight with enormous power output. Combined with digital signal processing. That's what we call flexibility! Locally controlled or completely networked. No matter what the requirements are. The integrated powerful digital signal processor (DSP) and controller allows for a troublefree and easy adjustment to any acoustical environment. Wear-free digital potentiometers, sequential remote power on, alive contacts for easy supervision, computer controlled monitoring - its enless list of useful feature make it the right choice for any installation. XR - the new definition of Intelligent Power
High Tech SMT Design Digital Signal Processor Excellent sound and superior impulse response Protection Circuits: DC, LF, HF, Thermal, Short Circuit, Current Limiter, 3 ms Muting Delay PHOENIX / Speakon High-End Switched Power Supply with Power Factor Correction (not XR4000) LED Indicators for SIGNAL, CLIP, PROTECT, POWER Temperature controlled, variable speed low noise fans Digital wear-free Volume Controls (can be operated manually) Stereo / Bridged / Parallel Mode Softstart Sequential Remote Power On Alive Contact Paging Input Monitor Output SXL Dataport Perfect Weight-to-Power ratio 3 Years Warranty
Technical Data: XR 2000: 2x 1400 W @ 2 Ohm 2x 1000 W @ 4 Ohm Class: H Frequency Response:20 Hz - 20 kHz (0 / -0.3 dB) THD: < 0.02% Signal-to-Noise Ratio: < -106 dB Channel Seperation: > 85 dB Input Sensitivity: +6 dBu Input Clipping: 22 dBu Input Impedance: 20 kOhm Damping Factor: 750 to 1200 @ 4 Ohm Cooling: 4 Fans (temp. reg. variable speed) Weight: 8 kg Dimensions: 2 RU / 483 x 88 x 454 mm(19" x 3.5" x 17.9“) | The new DEEP2 amp series features four class-H power amplifiers with toroidal core offering amplifying levels from 2 x 400 W till 2 x 810 W at 4 Ohm. During the development of this series we attached a great importance to the reliability and the durability of the amps in continuous operation, this is why we used exclusively high end and selected components for the construction of these products.
The DEEP2 series features a Clip Limiter as well as every common protection circuits. These amps are 2 Ohm and 4 Ohm (bridge) stable in continuous operation. On the rear panel you will find all the common In- and Outputs.
The DEEP2 series will convince every user thanks to a dynamic and very clear sound which is perfectly adapted for Subbass applications as well as for multifunctional speakers. All models are lightweight and feature a robust steel plate housing and a very user friendly and compact design.
The DEEP2 series will prove to be a profitable and reliable choice for bands, renting companies and professional users thanks to its excellent price/performance ratio.
Product type
Power Amplifiers
Type
PA Power Amplifiers
Rated ouput power (1kHz @ 2 Ohms)
2 x 800 W
Rated ouput power (1kHz @ 4 Ohms)
2 x 650 W
Rated ouput power (1kHz @ 8 Ohms)
2 x 450 W
Rated ouput power (1kHz @ 4 Ohms, bridged)
1600 W
Rated ouput power (1kHz @ 8 Ohms, bridged)
1300 W
Output circuitry
Class H
Frequency response
20 - 20000 Hz
THD
< 0.1 %
Signal-to-noise ratio
106 dB
Damping factor
> 400
Crosstalk
>80 dB
Gain
39 dB
Input sensitivity
0.775 V
Protection circuits
clip limiter , DC protection , short circuit , thermal overload
Controls
2 x volume , bridge/stereo mode selector , ground lift , mains switch (on/off)
Indicators
level , Limit , Power , Protect (protection circuit engaged) , Signal
Loudspeaker outputs
2
Speaker output connections
Speakon compatible , Terminal posts
Cooling
highly efficient, automatic
Operating voltage
transformer
Operating voltage
230 V AC / 50-60 Hz
Weight
15,9 kg
Features
Volex mains socket |
Reviews
There are no reviews yet.