| Content |
- Polar pattern: Cardioid
- Switchable -10dB PAD
- Frequency response: 20 - 20,000 Hz
- Max. SPL: 140/150 dB (THD = 0.5%)
- Electrical impedance: 200 Ohm
- Requires phantom power
- Diameter: 53 mm
- Length: 162 mm
- Net weight: 320 g
- Colour: Black
- Incl. shock mount
- Highly affordable AKG large-diaphragm microphone technology
- Cardioid polar pattern for multiplicity of vocal and instrument applications
The earlier model C 3000 has had a large fan club in the project studio and home recording worlds for years. For the new C 3000 B, AKG designed a special 1-inch large-diaphragm transducer that closely approximates the vibration performance of top-class studio microphones, but can be made at much lower cost.
Due to its surface area and special capsule tuning, the C 3000 B large-diaphragm transducer produces an exceptionally pleasing, smooth sound. Unlike in the C 3000, the switchable 10-dB preattenuation pad immediately follows the transducer in the signal path, thus increasing the C 3000 B\'s SPL capability by a true 10 dB. Loud sound sources are therefore no problem.
An acoustically optimized cardioid polar pattern makes the C 3000 B an excellent choice for both recording and live sound applications where high gain before feedback is paramount.
| Polar pattern |
cardioid |
| Frequency range |
20 to 20,000 Hz |
| Sensitivity |
25 mV/Pa (-32 dBV) |
| Max. SPL |
140/150 dB (k=0,5%) |
| Equivalent noise level (CCIR 468-3) |
25 dB |
| Equivalent noise level |
14 dB-A |
| Signal/noise ratio (A-weighted) |
80 dB |
| Preattenuation pad |
10 dB, switchable |
| Bass filter |
6 dB/octave below 500 Hz |
| Impedance |
200 ohms |
| Recommended load impedance |
>1000 ohms |
| Supply voltage |
9 to 52 V phantom power to DIN 45596 |
| Current consumption |
|
| Connector |
3-pin XLR |
| Finish |
silver gray |
| Net weight |
320 g / 11.3 oz. |
| Shipping weight |
950 g / 2.1 lbs. |
| Patent(s) |
Electrostatic transducer (Patent no. AT 395.225, DE 4.103.784, JP 2.815.488) |
|
Behringer B-5 Sputtered Diaphragm Studio Condenser Microphone
The B-5 is a professional gold-sputtered diaphragm condenser microphone featuring two interchangeable capsules for different pickup patterns (cardioid and omnidirectional). It is perfect for acoustic instruments, vocals and overhead miking. Its ultra low-noise transformerless FET input eliminates low frequency distortion. The -10 dB attenuator can be used with high volume signal sources, while the low-cut filter eliminates floor rumble. The microphone is delivered in a rugged hard case with stand adapter and windscreen.
|
|
|
|
|
|
|
Professional true condenser microphone for studio and live applications
|
|
|
2 interchangeable capsules with cardioid and omnidirectional pickup patterns
|
|
|
Low-mass gold sputtered diaphragm for ultimate sound reproduction
|
|
|
Perfect for acoustic instruments, voice and overhead etc.
|
|
|
Ultra low-noise transformerless FET input eliminates low-frequency distortion
|
|
Smooth, super-wide frequency response and incredible musicality
|
|
Switchable low-frequency roll-off and -10 dB input attenuation
|
|
Gold-plated 3-pin XLR output connector
|
|
Rugged construction with satin nickel-plated brass body
|
|
Custom microphone stand adapter, windscreen and transport case included
|
|
Manual Download |
| Acoustical operating principle | Pressure gradient transducer | | Directional pattern | Cardioid | | Frequency range | 20 Hz ... 20 kHz | | Sensitivity at 1 kHz into 1 kohms | 18 mV/Pa | | Rated impedance | 50 ohms | | Rated load impedance | 1000 ohms | | Equivalent SPL CCIR 468-3 | 21 dB | | Equivalent SPL DIN/IEC 651 | 10 dB-A | | S/N ratio CCIR 468-3 | 73 dB | | S/N ratio DIN/IEC 651 | 84 dB | | Maximum SPL for THD 0.5% | 140 dB | | Maximum output voltage | 13 dBu | | Dynamic range of the microphone amplifier DIN/IEC 651 | 130 dB | | Supply voltage | 48 V ± 4 V | | Current consumption | 3 mA | | Matching connectors | XLR 3F | | Weight | 480 g | | Diameter | 49 mm | | Length | 175 mm |
|
The CK-7 houses a 35mm gold-sputtered thin Mylar capsule. The CK-7 uses high grade Polystyrene and Metalized Polypropylene capacitors in the audio path. This represents a commitment to quality, as these normally are the type of "upgrade" components that are implemented by microphone modders/hot-rodders! Any studio can proudly offer the CK-7 as a vocal mic or utility condenser due to its versatility...It exudes class visually as well as sonically.
Manufactured using the finest materials yielding a very solid feel, superb structural integrity and rugged reliability. The versatile CK-7 mic is able to produce professional results with a clean sonic character. The included Custom Retro Shockmount is superb in allowing a precise positioning of the mic while inhibiting the transfer of unwanted vibrations up into the mic. This isolation allows for superior professional results. The 3 patterns allow the CK-7 to be used in a variety of situations.
The cardioid pattern is generally best used on vocals and single instruments. The omni mode works well in incorporating some room sound into the track. The figure 8 pattern allows 2 vocalists to use the mic at the same time from opposite sides. The CK-7 has separate -10 dB pad & 80 Hz LF roll off switches....The -10dB attenuation switch can be engaged when miking very high SPL sources to keep from overloading the electronics. The 80Hz high-pass filter switch can be engaged to reduce rumble and to keep unwanted low frequencies from "muddying up" the track.
Applications.
studio vocals, acoustic guitar, mandolin, drum overheads, piano, room mic
Specifications
Type: True Condenser
Polar Pattern(s): Cardioid , Omni , Figure 8
Capsule: Dual-sided 35mm center-terminated gold-sputter Mylar (6 micron)
Frequency Response: 20-20,000 Hz +/- 3dB
Output Impedance: |
| Large diaphragm cardioid microphone | | Pressure gradient transducer with with one-diaphragm capsule | | Transformerless circuitry | | Extremely low noise: 7 dB-A | | Includes swivel mount | | Straightforward handling for homerecording and professional studios | |
High-quality professional equipment for limited budgets
| Acoustical operating principle | Pressure gradient transducer | | Directional pattern | Cardioid | | Frequency range | 20 Hz ... 20 kHz | | Sensitivity at 1 kHz into 1 kohm | 23 mV/Pa | | Rated impedance | 50 ohms | | Rated load impedance | 1 kohms | | Equivalent noise level, CCIR1) | 17.5 dB | | Equivalent noise level, A-weighted1) | 7 dB-A | | Signal-to-noise ratio, CCIR1) (rel. 94 dB SPL) | 76.5 dB | | Signal-to-noise ratio, A-weighted1) (rel. 94 dB SPL) | 87 dB | | Maximum SPL for THD 0.5%2) | 138 dB | | Maximum output voltage | 13 dBu | | Dynamic range of the microphone amplifier (A-weighted) | 131 dB | | Supply voltage (P48, IEC 61938) | 48 V ± 4 V | | Current consumption (P48, IEC 61938) | 3 mA | | Matching connector | XLR3F | | Weight | approx. 450 g | | Diameter | 60 mm | | Length | 132 mm |
|
| Behringer C-2 2 Matched Studio Condenser Microphones
2 Matched Studio Condenser Microphones
- 2 matched condenser microphones for stereo studio recording and live applications
- Ideal as main and support microphones for studio and live applications
- Cardioid pickup pattern for effective feedback elimination
- Low-mass diaphragm for ultra-wide frequency response and ultimate sound reproduction
- Switchable low-frequency roll-off and input attenuation
- Ultra low-noise transformerless FET input eliminates low-frequency distortion
Excellent Source Isolation
Our C-2 mics also feature a low-frequency rolloff switch to eliminate infrasonics (mic handling noise, sound created by creaky stages), as well as a switchable -10 dB input pad to accommodate hot signals, such as a really loud vocalist or overzealous cellist.
The cardioid pickup pattern provides unparalleled sound source separation and feedback rejection. C-2 mics contain ultra low-noise transformerless FET input circuitry that can handle extreme dynamics with a maximum sound pressure level of 136 dB. So even if the featured performer at your next recording session or live show happens to be a revved-up jet engine, this workhorse mic will not distort!
Sound That Astounds
Every stitch of these mics is designed to deliver beautiful sound. Beginning with the gold-plated 3-pin XLR connector, you get the highest signal integrity.
Once connected to your system, youʼll notice these twin pro-caliber microphones have a 4 dB boost in the 1 kHz - 8 kHz range. For those of you new to condenser mics, this basically means youʼll get a slightly brighter sound that will give the perfect shape to cymbals and overhead miking. Acoustic pianos and choirs also benefit greatly from this type of frequency response.
Excellent Source Isolation
The cardioid pickup pattern provides unparalleled sound source separation and feedback rejection. C-2 mics contain ultra low-noise transformerless FET input circuitry that can handle extreme dynamics with a maximum sound pressure level of 136 dB. So even if the featured performer at your next recording session or live show happens to be a revved-up jet engine, this workhorse mic will not distort!
Our C-2 mics also feature a low-frequency rolloff switch to eliminate infrasonics (mic handling noise, sound created by creaky stages), as well as a switchable -10 dB input pad to accommodate hot signals, such as a really loud vocalist or overzealous cellist.
You Are Covered
We always strive to provide the best possible Customer Experience. Our products are made in our own MUSIC Group factory using state-of-the-art automation, enhanced production workflows and quality assurance labs with the most sophisticated test equipment available in the world.
As a result, we have one of the lowest product failure rates in the industry, and we confidently back it up with a generous 3-Year Warranty program. |
Reviews
There are no reviews yet.