QSC CMX-300V POWER AMPLIFIER 2x300W RMS @ 4Ω, 2x430W RMS @2Ω, bridged (mono) 830W RMS @ 4Ω.

Stereo Mode Ratings (Both Channels Driven):

    8 ohms:
    - FTC 20 Hz - 20kHz, 0.1% THD: 185W
    - EIA 1 kHz, 0.1% THD: 200W
    4 ohms:
    - FTC 20 Hz - 20kHz, 0.1% THD: 280W
    - EIA 1 kHz, 0.5% THD: 300W (1% THD)
    2 ohms:
    - EIA 1 kHz, 1% THD: 430W

Bridged Mono Mode Ratings/Specifications:

    8 ohms:
    - FTC 20 Hz - 20kHz, 0.1% THD: 530W
    - EIA 1 kHz, 0.1% THD: 600W
    4 ohms:
    - EIA 1 kHz, 1% THD: 830W
    70V Direct Drive:
    - EIA 1 kHz, 1% THD: 600W
    Signal to Noise, 20Hz-20kHz, 0.1% THD, 8 Ohms: > -100dB
    Input Sensitivity @ 8 Ohms: 1.15V (+3.4 dBu)
    Voltage Gain @ 8 Ohms: 31.6x (30 dB)
    Output Circuitry: Class AB
    Power Requirements (120V):
    - 1/8 power pink noise at 4 ohms: 4.4A
    - 1/3 power pink noise at 4 ohms: 6.6A
    Power Requirements (230V):
    - 1/8 power pink noise at 4 ohms: 2.2A
    - 1/3 power pink noise at 4 ohms: 3.3A
    Distortion (SMPTE-IM):

XB Series - Intelligent Power

Power Without Compromises.
The XB is designed for paging, music and alarm signals. Versatile, dynamic
and extremely rugged according to IEC286-3. For the highest requirements
in safety and quality.
Sequential power on, alive contacts and incorporated ground fault detection-
the XB is the solution under all conditions. Without the need for additional
equipment. For uninterrupted and troublefree operation.

High Tech SMT Design
Protection Circuits: DC, LF, HF, Thermal, Short Circuit, Current Limiter,
3 ms Muting Delay
PHOENIX / Speakon
LED Indicators for POWER, SIGNAL, CLIP, PROTECT
Temperature controlled, variable speed low noise fans
Volume Controls at the back
Stereo / Bridged / Parallel Mode
Softstart
Sequential Remote Power On
Alive Contact
Ground Lift
3 Years Warranty

TECHNICAL DATA:
XB 400:  2x 200 W @ 4 Ohm
Class:  AB
Frequency Response: 20 Hz - 20 kHz (0 / -0.3 dB)
THD:  < 0.025%
Signal-to-Noise Ratio:  < 103 dB
Channel Seperation:  > 85 dB
Input Sensitivity:  +6 dBu
Input Clipping:  22 dBu
Input Impedance:  20 kOhm
Damping Factor:  500 @ 4 Ohm
Cooling:  2x fan (temp. reg. variable speed)
Weight:12 kg /(26 lbs)                                    
Dimensions:  2 RU / 483 x 88 x 382 mm (19" x 3.5" x 15“)

• Output power: 450W @ 4 Ohms stereo, 280W @ 8 Ohms stereo
• High-current toroidal transformers for greater power and low noise
• Independent user-defeatable peak limiters reduce distortion
• Selectable High-Pass filter at 30Hz or 50Hz
• XLR and 1/4' TRS input jacks
• Binding post and Speakon?-type outputs
• Front mounted gain controls for easy access
• Signal and Peak LED indicators to monitor performance
• Short circuit, thermal, subsonic, RF protection, output DC offset
• Power on/off muting

• Rack mount stereo powered monitor speaker system
• New AES/EBU digital input
• lndependent MUTE function
• Sophisticated control panel section
• Ideal where space is at a premium

• Stereo analog balanced +4DBu inputs with combo connectors (XLR & 1/4" plug).
• AES/EBU digital input with XLR connector working with fs 44.1kHz to 96kHz.
• Sophisticated control panel section including 26-dot stereo LED meter, biaxial stereo gain control, phone jack, Channel select switch as well as Input select switch.
• Independent MUTE function by holding down CH SEL key for a while.
• Auto Mute when powering on*.
• D-class power amplifier (10W x 2) for clear sound reproduction and light weight construction.
• Multi-voltage power supply.

Speaker Section

• Unit: 110 x 40mm cone type, magnetically shielded, x 2
• Impedance: 8 ohms
• Output SPL: 84 dB/W (1m)
• Frequency response: 200Hz to 20kHz

Amplifier Section

• Rated output power: 10W or more (8 ohms, 1kHz)
• Residual noise: -60 dBV or less (DIN AUDIO)
• Distortion: 0.5% or less (10W / 4 ohms, 1kHz)

Digital input

• Connector: XLR-3-31 type
• Digital input Format: IEC60958 (AES/EBU)
• Digital inputSampling frequency: 44.1kHz to 96 kHz
  

Analog input

• Connector: XLR / 1/4" combi-jack
• Analog input Nominal input level +4dBu (XLR), -10 DdBV (1/4“)
• Analog input Input impedance 10k ohms or more

Phones

• Connector: 1/4" stereo jack
• Applicable load imp. 8 ohms or more
• Rated output power 20mW + 20mW (32 ohms, 1kHz)

General

• External dimensions: 430(W) x 44(H) x 282(D) mm
• Weight: Approx. 3.5kg
• Power requirement: 100 - 240V~, 50/60Hz
• Power consumption: 10W

VLP Series Powere Amplifier

Output Power: 300W RMS Per Channel @ 4 Ohms, 1kHz, 0.1% THD 200W RMS Per Channel @ 8 Ohms, 1kHz, 0.1% THD (Bridge Mode, Mono) 600W RMS @ 8 Ohms, 1K Hz, 1% THD

Total Harmonic Distortion: Less Than 0.1% (20Hz - 20kHz @ 8 Ohms)

Frequency Response: (+/-01db, @rated output Power, 8 Ohms): 20Hz - 20K Hz

Slew Rate: 15V Per usec

Damping Factor @ 8 Ohm: 300

Impedance: 20 Ohms balanced / 10 Ohms unbalanced

Cooling System: 2 indivdual fans

Special Features: High/Low Pass Filter / Input Sensitivity Selector / Ground Lift Limiter

Dimensions (LxWxH): 14" x 19" x 3.5" / 360 x 482 x 88mm 2-rack mount spaces

Weight: 33 lbs. / 15 Kgs.

Special Features: High/Low Pass Filter; Input Sensitivity Selector; Ground Lift; Limiter

HPS 1500 is a 2 channel power amplifier that delivers up to 2 x 750 W RMS @ 4 Ω (1500 W RMS bridged @ 8 Ω).

XLR inputs for patching in signals as well as Speakon ports for connecting speaker systems are provided for the maximum flexibility.
A forced air cooling system maintains a low operating temperature.