This professional stereo power amplifier, working in class-H mode, provides 2x1600W, at an efficiency of around 85%. A massive transformer based power supply and hand selected components makes this power rating possible with exceptional audio quality and absolute reliability, even in the 2 Ohm mode. The output stage is fully protected against over-temperature, short circuit, […]
This professional stereo power amplifier, working in class-H mode, provides 2x1600W, at an efficiency of around 85%.
A massive transformer based power supply and hand selected components makes this power rating possible with exceptional audio quality and absolute reliability, even in the 2 Ohm mode.
The output stage is fully protected against over-temperature, short circuit, RFI and equipped with soft start circuit and temperature-controlled fan cooling.
The integral soft clip limiter protects against damage to the connected loudspeakers.
The activity of a protective circuit, signal and limiter is shown for each channel by LEDʼs.
AMPLIFIER SPECIFICATIONS
Power output stereo 2Ω:
2 x 1600 Watt rms
Power output stereo 4Ω:
2 x 1100 Watt rms
Power output stereo 8Ω:
2 x 700 Watt rms
Power output bridged 4Ω:
3200 Watt rms
Power output bridged 8Ω:
2200 Watt rms
Frequency Response:
20 Hz ÷ 20 kHz
Signal/noise rate:
> 102 dB
Crosstalk:
> 65 dB
Distortion (THD+N):
Intermodulation:
Damping factor:
400:1 (8 W)
Slew rate:
50 V/μS
INPUT SECTION
Input connector:
2 x XLR balanced, 6,3mm jack unbalanced
Input sensitivity:
0 / 0.775 dBm/V RMS
Input impedance:
20.000 kΩ
Controls:
Volume control for each channel
OUTPUT SECTION
Output connector:
2 x Neutrik Speakon 4 ways
SYSTEM PARAMETERS
Cooling:
Two-speed fan
Protections:
Thermal, temperature, direct current, short circuit, RFI
POWER REQUIREMENT
Operating voltage:
220÷240 / 110÷120 ~ 50 / 60 V ~ Hz
Max.current:
16 A
Power Consumption:
6500 W
PHYSICAL SPECIFICATIONS
Height:
132 / 5.19 mm/inch
Width:
483 / 19.01 mm/inch
Depth:
455 / 17.91 mm/inch
Net Weight:
29.5 / 65.03 Kg/Lbs
SHIPPING INFORMATION
Package height:
200 / 7.87 mm/inch
Package width:
575 / 22.63 mm/inch
Package depth:
555 / 21.85 mm/inch
Shipping Weight:
32.5 / 71.64 Kg/Lbs
Weight
32.50 kg
Reviews
There are no reviews yet.
Be the first to review “RCF HC 3200: 3200 W, 2 IN, HIGH CURRENT STEREO POWER AMPLIFIERS” Cancel reply
This professional stereo power amplifier, working in class-H mode, provides 2x1600W, at an efficiency of around 85%.
A massive transformer based power supply and hand selected components makes this power rating possible with exceptional audio quality and absolute reliability, even in the 2 Ohm mode.
The output stage is fully protected against over-temperature, short circuit, RFI and equipped with soft start circuit and temperature-controlled fan cooling.
The integral soft clip limiter protects against damage to the connected loudspeakers.
The activity of a protective circuit, signal and limiter is shown for each channel by LEDʼs.
AMPLIFIER SPECIFICATIONS
Power output stereo 2Ω:
2 x 1600 Watt rms
Power output stereo 4Ω:
2 x 1100 Watt rms
Power output stereo 8Ω:
2 x 700 Watt rms
Power output bridged 4Ω:
3200 Watt rms
Power output bridged 8Ω:
2200 Watt rms
Frequency Response:
20 Hz ÷ 20 kHz
Signal/noise rate:
> 102 dB
Crosstalk:
> 65 dB
Distortion (THD+N):
Intermodulation:
Damping factor:
400:1 (8 W)
Slew rate:
50 V/μS
INPUT SECTION
Input connector:
2 x XLR balanced, 6,3mm jack unbalanced
Input sensitivity:
0 / 0.775 dBm/V RMS
Input impedance:
20.000 kΩ
Controls:
Volume control for each channel
OUTPUT SECTION
Output connector:
2 x Neutrik Speakon 4 ways
SYSTEM PARAMETERS
Cooling:
Two-speed fan
Protections:
Thermal, temperature, direct current, short circuit, RFI
POWER REQUIREMENT
Operating voltage:
220÷240 / 110÷120 ~ 50 / 60 V ~ Hz
Max.current:
16 A
Power Consumption:
6500 W
PHYSICAL SPECIFICATIONS
Height:
132 / 5.19 mm/inch
Width:
483 / 19.01 mm/inch
Depth:
455 / 17.91 mm/inch
Net Weight:
29.5 / 65.03 Kg/Lbs
SHIPPING INFORMATION
Package height:
200 / 7.87 mm/inch
Package width:
575 / 22.63 mm/inch
Package depth:
555 / 21.85 mm/inch
Shipping Weight:
32.5 / 71.64 Kg/Lbs
The new Audio 3-stage CLASS-H SMPS amplifiers incorporate all the features to meet all your needs, whether youʼre starting a P.A. amplifier project from scratch or just need to upgrade your present sound reinforcement equipment. In the amps, youʼll find 2 and 4 channel models, all offering high power levels at low distortion in the range 1.5 to 6 kW, yet weighing around 8.6 kg and only 30 cm deep.
Model Name: SP4K
Output Power 1 kHz, 500
Crosstalk (20 Hz - 20 kHz): > 75 dB
Voltage Gain (selectable): 26 / 32 / 38 dB
Input Sensitivity: 4.0 / 2.0 / 1.0 V
Protection: Soft-start, Turn-on Turn-off transients, Muting at turn-on, Over-heating, DC, RF, Short-circuit, Open or mismatched loads, Overloaded power supply, ICL (Inteligent Clip Limiting), PMS (Power Management System), SSP (SOA Sentry Protection)
Controls: On / Off Switch, Volume, Voltage Gain, Dual / Link Switchable, Bridge Mode Configuration Switch
A full model revision takes Yamaha's high-end PC-N power amplifiers to the next level - the PC-1N
Series. The new PC-1N Series amplifiers feature an extraordinarily solid low end, rich midrange,
and superbly defined highs. They also deliver fast response and exceptional stability even in the
face of serious power supply limitations. Refinements throughout this expanded five-model lineup
make these amplifiers the new benchmarks for quality, reliability, and versatility in professional
applications. Frequency Response: 10 Hz – 40 KHz. Output Power: 2 x 750 Watt / 8Ω RMS,
2 x 1150 Watt / 4Ω RMS, 2300 Watt / 8Ω bridge RMS. Weight: 12,5 Kg.
Solid DYNACORD technology for fixed installations at very competitive prices. DSA power amplifiers offer a very high, stable output with high efficiency at a high performance level and are therefore the ideal choice for typical fixed installation applications. The connectivity consequently provides Phoenix type in/outs, the input level controls are located on the rear panel, also a switchable high-pass filter (50 Hz, 18 dB/oct) and a Ground Lift switch. The POWER REMOTE connector makes the task of remote controlling the power amplifier as well as switching it on and off simple. For further remote-supervision and –control possibilities and integration into IRIS-Net networks, an optional remote control module (RCM-810) is available.
Number of Channels: 2
Output Power: (per channel)
8 ohms 625W 4 ohms 1150W 2 ohms 2100w
Output Power: (bridged)
8 ohms 2300W 4 ohms 4200w
THD%: (@1dB below max output)
@ 1kHz 20Hz to 20kHz Gain / Sensitivity:
Gain 32/36dB Sensitivity (for max power) +7.5/3.5dBu (1.8/1.2V)
Frequency Response: 20Hz to 20kHz (+ 0/- 0.5dB)
Power Consumption:
Nominal @ 240v into 4 ohms 2.8A Nominal @ 120v into 4 ohms 5.6A
Dimensions: (2U) (mm)
Amplifier 88(h) x 482(w) x 460(d) Single Box (UK shipping) 230 x 580 x 560 Double Box (outside UK) 250 x 610 x 600
This website uses cookies to improve your experience. We'll assume you're ok with this, but you can opt-out if you wish. Cookie settingsACCEPT
Privacy & Cookies Policy
Πολιτική χρήσης
Αυτός ο ιστότοπος χρησιμοποιεί cookies για να βελτιώσει την εμπειρία σας ενώ περιηγείστε στον ιστότοπο. Από αυτά τα cookies, κάποια cookie κατηγοριοποιούνται ως απαραίτητα να αποθηκεύονται στο πρόγραμμα περιήγησης σας, καθώς είναι απαραίτητα για τη λειτουργία βασικών λειτουργιών του ιστότοπου. Χρησιμοποιούμε επίσης cookies τρίτων που μας βοηθούν να αναλύσουμε και να κατανοήσουμε πώς χρησιμοποιείτε αυτόν τον ιστότοπο. Αυτά τα cookies θα αποθηκευτούν στο πρόγραμμα περιήγησης σας μόνο με τη συγκατάθεσή σας. Έχετε επίσης την επιλογή να εξαιρεθείτε από αυτά τα cookies. Ωστόσο, η εξαίρεση από ορισμένα από αυτά τα cookie μπορεί να επηρεάσει την εμπειρία περιήγησης σας.
Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.
Any cookies that may not be particularly necessary for the website to function and is used specifically to collect user personal data via analytics, ads, other embedded contents are termed as non-necessary cookies. It is mandatory to procure user consent prior to running these cookies on your website.
Reviews
There are no reviews yet.