Content |
Weighing only 18 grams (0.6 oz.), this ultra-light condenser pickup is ideal for acoustic guitar, mandolin, violin, and most other stringed instruments. The C 411 will give a clear and uncolored sound without changing the balance of the instrument. Attaching the C 411 on or near the bridge or anywhere else on the instrument is easy with the included non-marring, reusable, solventfree adhesive compound.
C 411 PP: For hardwire applications, with standard XLR connector for phantom powering. |
The e 865 is a fully professional super-cardioid vocal microphone utilising the very best in condenser microphone technology to achieve new standards of quality and sound. The microphone capsule insorporates special blast/pop protiction plate to shield the diaphragm from excessive sound pressure levels. ON/OFF Switch.
- Pick-up pattern : super cardioid
- Sensitivity in free field, no load : (1kHz) 3 mV/Pa
- Max. Sound pressure level (aktiv) : 150 dB
- Nominal impedance : 200 Ohm
- Min. terminating impedance : 1000 Ohm
- Dimensions : d 47 x 193 mm
- Weight : w/o cable 311 g
- Frequency response (microphone) : 40.....20000 Hz
- Phantom powering : 12 - 48 V
| The NT5 matched pairs are a masterpiece of small-diaphragm cardioid-
condenser microphone design.Intended for recording acoustic instruments,
drum overheads, cymbals and live performances, the compact externally
polarized mic employs a .5? capsule, an active J-FET impedance converter
with bipolar output buffer.
Finished in durable satin nickel, the NT5 is intended for either single or stereo
X/Y mic set-ups. The NT5 matched pairs comesupplied in a custom carry case
with windshields and mounts.
SPECIFICATIONS:
Acoustic principle: Externally polarised single diaphragm
Directional pattern: Cardioid
Frequency range: 20Hz - 20kHz
Output impedance: 100?
Signal noise ratio din iec 651: 78dB
Equvalent noise: Maximum spl: 143 dB @ 1% THD into 1k_
Sensitivity:
-38 dB re 1v/Pa ± 2 dB equivalent to 12mV/Pa where 1 Pa = 94dBSPL
Power supply voltage: P48 Supply (38V?52V), P24 Supply (20V-26V)
Current consumption: 4 mA, 2 mA,
Weight: 100g |
Technical specifications Polar pattern | | hypercardioid | Frequency range | | 50 to 20,000 Hz | Sensitivity | | 20 mV/Pa (?34 dBV) | Max. SPL | | 125 dB (k=1 %) | Equivalent noise level | | 21 dB-A | Signal/noise ratio (A-weighted) | | 73 dB | Impedance | | 600 ohms | Recommended load impedance | | >2000 ohms | Supply voltage | | 9 to 52 V phantom power, requires DPA adapter (supplied with most Installation Modules) | Current consumption | | | Connector | | Discreet Acoustics Modular standard | Finish | | matte dark gray | Dimensions | | 13.5 x 20 mm dia. (0.5 dia. x 0.8 in.) | Net weight | | 5 g (0.17 oz.) | Shipping weight | | 88 g (3.1 oz.) | Accessories (included) | | W 30 |
|
The ME 66 is a shot gun microphone head designed for use with the K6 and K6P powering modules. It is especially suitable for reporting, film and broadcast location applications and for picking up quiet signals in noisy or acoustically live environments as it discriminates against sound not emanating from the main pick-up direction. Matt black, anodised, scratch-resistant finish.
Pick-up pattern : super-cardioid/lobar
Sensitivity in free field, no load (1kHz) : 50 mV/Pa +- 2,5 dB
Nominal impedance : 200 Ohm (K6)
Min. terminating impedance : 1000 Ohm ( K6)
Equivalent noise level : 10 dB
Dimensions : d 22,5 x 221 mm
Weight : 65 g
|
Back-electret Microphone Capsule suitable for K6 and K6P Powering Modules. The ME 64 is a cardioid microphone capsule designed for use with the K6 and K6P powering modules. It has a very wide range of applications including reporting, interviews, dubbing, live sound reinforcement and recording applications. Matte black, anodized, scratch-resistant finish.
Features
Excellent directivity across whole frequency range
Very good feedback rejection
Effective rejection of incidental rear noise
High speech clarity
High maximum sound pressure level
Wide frequency range
Integrated pop filter
|
Reviews
There are no reviews yet.