Content |
Power handling (watts): 150 (RMS)
Sensitivity (dB): 89
Nominal impedance (ohms): 8
Magnetically shielded
W x H x D (mm): 203 x 905 x 242 (each)
Weight (kg): 14 (each)
Frequency response (Hz): 45 - 45,000
Connections: Gold-plated 4mm banana socket/binding posts
Drivers: HF: Dual ring-radiator design
LF: 2 x 130mm pressed allow cones with twin Neodymium magnets and long throw voice coil
Supplied accessories: Removable grilles
Finish: Black ash or walnut |
Three way, bass-reflex
Sub-woofer 200 mm.
coated paper
Mid-woofer 130 mm. paper
Tweeter 28 mm. soft dome
coated silky fabric
Impedance: 6 Ohm (min. 4)
RMS Power: 120 W
MAX Power: 200 W
Efficiency: 90 dB/W/1 m
Dimensions: 325x385x1130 mm.
Net weight: 26 Kg.
Finish:
cherrywood, metallized mat grey
|
Single Ported HiVe® II technology Sealed Mid-range TLE® 2 x 6.5” long-throw RDT® bass drivers 1 x 4” RDT® mid-range driver 1 x C-CAM® high frequency ribbon transducer All cabinet finishes have hand-upholstered front baffles in Ingleston Black premium grade leather. Finish options: Santos Rosewood veneer with clear gloss piano lacquer Ebony veneer with clear gloss piano lacquer Piano black gloss Optional dedicated floor stands are available Frequency Response: 35 Hz - 100 KHz Sensitivity (1W@1M): 90 dB Nominal Impedance: 4 Ohms Maximum S.P.L (Per pair in room): 117.8 dBA Power Handling (RMS): 250 W Recommended Amplifier Requirements (RMS): 100 - 250 W Bass Alignment: Rear Ported HiVe®II technology Sealed Mid-range TLE® Mid / H.F Crossover Frequency: 3600 Hz Bass Low Pass Crossover Frequency: 600 Hz Drive Unit Complement: 2 x 6.5" long-throw RDT® bass drivers 1 x 4" RDT® mid-range driver 1 x C-CAM® high frequency ribbon transducer External Dimensions - Including Fixed Plinth (H x W x D): 998 x 360 x 375 mm (39 5/16 x 14 3/16 x 14 3/4 inches) Weight (each) Including Plinth: 33Kg (72.7 lbs) User's Manual AVAILABLE IN THESE COLOR FINISHES
|
2 x 6 ½ ¨ Polymer/Mica Cone
with Rubber Surround
1 x 1¨Silk Polymer Composite
Dome
Amplifier Power 20-250 W/ch
Impedance 8 Ohms
Sensitivity 90dB
Dimensions 102 x 22 x 40
ALSO AVAILABLE IN CHERRY COLOR
|
System Format: 3 Way Frequency Response: 35 Hz - 60 kHz Sensitivity (1W@1M): 89 dB Nominal Impedance: 8 ohms Maximum S.P.L (Per pair in room): 114.5 dBA Power Handling (RMS): 150 W Recommended Amplifier Requirements (RMS): 100 - 150 W Bass Alignment: Bass reflex. HiVe port system Crossover Frequency: L.F - M.F: 400 Hz M.F - H.F: 2.6 kHz Drive Unit Compliment: 2 x 5.5" RST bass driver 1 x 4" RST mid-range driver 1 x C-CAM H.F ribbon transducer External Dimensions excl Stand (H x W x D) 951 x 170 x 300 mm (37 7/16 x 6 11/16 x 11 13/16 inch) Weight (each) Excluding stands: 22.2 Kg (48.9 lbs)
|
Dimensions | Metric :46" H x 8-1/2" D x 5-1/2“W | 116.8 x 21.6 x 14.0 cm
Height with Base | Metric :47.5" | 120.7 cm
Base Dimensions | Metric :10-1/2" W x 14" D | 26.7 x 35.6 cm
Driver Complement :One 1" pure aluminum dome tweeter; Two 4-1/2" BDSS midrange drivers; One 5" x 10" long-throw racetrack subwoofer pressure coupled to two 5" x 10" long-throw racetrack radiators.
Frequency Response :16 Hz – 30 kHz
Impedance :Compatible with 8 Ohm outputs
Sensitivity :93 dB
Recommended Associated Amplifier Power :20 – 250 watts
A/V Receiver Crossover Setting :Large; Full Bandwidth
Internal Amplifier Power :300 watt
Auto On / Off :Signal Sensing (US) | Signal Sensing and Switched (International)
Power Requirements :110 volts Alternating Current (US) | 220 volts Alternating Current (International)
Inputs :One pair of 5 way binding posts; One LFE input (optional)
Fuse :3.2 amp 250 volt Slo Blo (US) | 2 amp 250 volt Slo Blo (International)
Enclosure :Aircraft grade extruded aluminum
Available Finishes :Gloss Black
Base :Granite
Accessories :Plastic foot tippers; Isolation spikes
Packaging :One to a carton
Weight | Metric :54 lbs | 24.5 kg
Warranty :5 Years; 3 Years for Amplifiers
|
Reviews
There are no reviews yet.