Content |
Amplifier power (watts): 200 watt RMS built in
Controls: Volume, frequency roll-off, crossover frequency, phase, notch filter
Auto mute/power: Yes
Magnetically shielded
W x H x D (mm): 360 x 410 x 325
Weight (kg): 17
Frequency response (Hz): Down to 25Hz
Connections: Mono line in (via 1 x gold-plated RCA/phono socket)
Stereo line in (via 2 x gold-plated RCA/phono)
Stereo line out (via 2 x gold-plated RCA/phono sockets)
closed box design
Finish: black ash/ walnut
Supplied accessories: Removable grille |
Crossover Tuning
Mushrooms
Description Active closed-box subwoofer system
Drive unit ø250mm (10 in) paper/Kevlar® cone long-throw
Frequency range -6dB at 18Hz and 25/140Hz adjustable (EQ at A)
Frequency response ±3dB 25Hz – 40/140Hz adjustable (EQ at A)
Bass Extension -6dB at 18Hz (position A)
-6dB at 23Hz (position B)
-6dB at 28Hz (position C)
Amplifier Power output: 500W
Rated power consumption: 98W / 1W standby
Input impedance: 33kΩ
Signal / noise: >90dB
Functions: Input level (line in)
Input level (speaker in)
Low-pass filter frequency (line in only)
Low-pass filter bypass
Bass extension
Bass roll-off alignment
Auto sense on/standby
Phase switch
Inputs: Line In (RCA Phono)
Speaker in (Binding post)
12v trigger (3.5mm jack)
Low-pass filter
Active 4th-order, variable cut-off frequency
Dimensions Height: 325mm (12.8 in) not including feet
Width: 325mm (12.8 in)
Depth: 375mm (14.8 in) including grille and controls
Net weight 15.5kg (34.4 lb)
Finishes Matte Black
|
Dimensions | Metric :12” W x 17-7/8” D x 14-7/16” H | 30.5 x 45.4 x 36.7 cm
Driver Complement :One high-definition 10" woofer pressure coupled to one 10" low bass radiator.
Frequency Response :18Hz – 150 Hz
Internal Amplifier Power :300 watts
Auto On / Off :Signal Sensing (US) | Signal Sensing and Switched (International)
Power Requirements :110 volts Alternating Current (US) | 220 volts Alternating Current (International)
High Level Inputs :Two pairs of 5 way binding posts
High Level Outputs :Two pairs of 5 way binding posts
Low Level Inputs :One LFE input (for SW preout only)
High Pass Crossover :Non Variable 6 dB/octave @ 80 Hz: Available only with high level inputs and outputs
Low Pass Crossover% :24 dB/octave, continuously variable from 40 Hz – 150 Hz: Available with high level inputs only
Available Finishes :Matte Black
Fuse :3.2 amp 250 volt Slo Blo (US) | 2 amp 250 volt Slo Blo (International)
Packaging :One to a carton
Weight | Metric :31 lbs | 14.1 kg
Warranty :5 Years; 3 Years for Amplifiers
|
Pressure vessel enclosure
500W ICEpower® amplifier
Switch mode power supply
Description Active closed-box subwoofer system
Drive unit 2x f200mm (8 in) mica / aluminium diaphragm long-throw
Frequency range -6dB at 18Hz and 40/140Hz adjustable (EQ at i)
Frequency response ±3dB 21Hz – 31/110Hz adjustable (EQ at i)
Power output: 500W
Rated power consumption: 110W (105W - 100V version)
Input impedance: 100kΩ
Signal / noise: >90dB
Functions: Volume level
Low-pass filter frequency
Bass roll-off alignment
Auto sense on/standby
Phase switch
Inputs: Line In (RCA Phono)
Speaker Level In (FCC68 4/4)
|
System Format: Sealed Cabinet. 25mm M.D.F construction with internal bracing. Sealed amplifier compartment
Low Frequency Limit: 18 Hz
Upper Frequency Limit: 40 - 120 Hz Variable
Low Pass Filter Alignment: Active 4th order 24dB/octave (6/12/18/24 dB user adjustable)
Amplifier Power Output 650 watts Continuous. 1200 watts (peak)
Amplifier Classification D2AudioTM* DSP controlled, Class-D amplifier system. High current switch mode power supply (smpsu)
Equalisation 4 Settings (Off/Music/Movie/Impact)
Phase Control 0-90-180-270 degrees
Auto Sensing Input Level Requirements Line Level > 2mV. Standby after 10 minutes if no signal sensed
Digital Volume Level -60 to +10dB in 1dB increments
Drive Unit Complement 1 x 15” C-CAM® sub-woofer driver featuring triple suspension
3” long throw voice coil
12V Trigger Input 3.5mm mono jack socket
Connections Stereo RCA in/out
LFE in/out
12V Trigger in (3.5mm mono jack)
LEO* - 3.5mm Microphone input jack (microphone supplied)
Input Impedance 20 kohms
Dimensions (H x W x D) 430 x 400 x 400 mm (16 15/16 x 15 3/4 x 15 3/4 Inches)
Grille Depth 28 mm (1 1/8 Inches)
Weight (unpacked) 35.3 kg (77.6 lbs)
Mains Input Voltage 100 - 120 Vac / 220 - 240 Vac 50/60 Hz (Factory preset)
Electrical Certifications CE/CB/ETL/Fcc/ErP (Energy saving compliant)
Power Consumption Maximum 1000W. Standby
Fuse Type 20mm UL/VDE (Value is region specific)
IR Remote Control Code NEC SH6122
|
Amplifier Output: 1000 watts (RMS) 2000 watts (Peak) Frequency Response: 16Hz to 40/160Hz variable Crossover (Low Pass): 40Hz - 160Hz Variable slope characteristic from 12 - 36dB/Octave Sub-Sonic Filter (High Pass): 16Hz - 31Hz EQ: 4 x Presets 1 x User Setting Equalisation: Graphic 9 band Equaliser ±6dB in 0.5dB steps Volume Level: -80 - 0dB (1dB increments from 0 to -30dB & 2dB increments from -31 to -80dB) Auto Sensing Input Requirements: Line Level>5mV (RMS) Variable delay time 5, 10, 15, 20, 25 & 30 minutes Variable Phase Control: 0. 45. 90, 135, 180, 225, 270 & 315º Internal Memory: 3 Independent memory locations Cabinet Specification: Sealed Cabinet with 25mm thick M.D.F construction with critical internal bracing Amplifier Classification: Class-D amplifier with DSP control Driver Complement: 1 x 15" C-CAM long throw sub-woofer driver featuring triple suspension and a 4" long throw voice coil External Dimensions - Excluding Plinth: Width: 485mm (19 inches) Height: 455mm (18 inches) Depth: 475mm (18 3/4 inches) Weight: 50 Kg (110lbs) Mains input Voltage: 100 - 240 Vac 50/60Hz (Factory Set) Trigger Input: 3.5mm Jack input, +12Vdc = On State User's Manual AVAILABLE IN THESE COLOR FINISHES
|
Reviews
There are no reviews yet.