| Description | The ah PAD series is designed to isolate studio monitors acoustically, i.e., avoid disturbing resonances with the surface on which they stand, which results in a significantly improved sound. The two-component design results in three possible combinations (horizontal placement + two different angles. | | | The ah PAD series is designed to isolate studio monitors acoustically, i.e., avoid disturbing resonances with the surface on which they stand, which results in a significantly improved sound. The two-component design results in three possible combinations (horizontal placement + two different angles. |
- Infinitely variable height adjustment
- Tilt angle up to +/- 15°
- 360° rotatable
- EVA padded bearing surface
- Anti-tip for the speaker
|
- Infinitely variable height adjustment
- Tilt angle up to +/- 15°
- 360° rotatable
- EVA padded bearing surface
- Anti-tip for the speaker
|
| Content | The ah PAD series is designed to isolate studio monitors acoustically, i.e., avoid disturbing resonances with the surface on which they stand, which results in a significantly improved sound. The two-component design results in three possible combinations (horizontal placement + two different angles.
Product type
Other Studio and Recording Equipment
Material
High density acoustic foam
Colour
charcoal
Setup
2-layer
Foam density
38 kg/m
Width
170 mm
Height
40 mm
Depth
300 mm
Weight
0,12 kg |
- Height Adjustable Near-Field Monitor Stand
Speaker plate dimensions: 9” square - 23 cm square
Height Positions (5): 30.7”, 34”, 37.4”, 40.7”, 44” - 78, 86.5, 95, 103.5, 112 cm
Base Size: 14.5” x 16.1” - 37 x 41 cm
Weight capacity: 125 lb - 57 kg
Weight: 11.1 lb - 5 kg
|
- Height: 30 - 40 - 50 cm (11.8 - 15.5 - 19.7“), 3 steps, with safety pin
- Maximum load: 25 kg (55.1 lb)
- Material: Steel (pole and plate) and nylon (joint)
- Top plate: Square, sturdy
- Top plate dimensions: 23 x 23 cm (9 x 9“)
- Bottom plate dimensions: 24 x 24 cm (9.4 x 9.4“)
- Quantity: 2 stands
- Weight: 2.75 kg (6 lb) per stand
| Isolation Pad for Studio Monitors 265 x 330 mm
The ah PAD series is designed to isolate studio monitors acoustically, i.e., avoid disturbing resonances with the surface on which they stand, which results in a significantly improved sound. The two-component design results in three possible combinations (horizontal placement + two different angles.
Product type
Other Studio and Recording Equipment
Material
High density acoustic foam
Colour
charcoal
Setup
2-layer
Foam density
38 kg/m
Width
265 mm
Height
40 mm
Depth
330 mm
Weight
0,22 kg | A mix's sound and feel is heavily influenced by having your monitors placed in the proper position. In a home studio, however, where space is at a premium, it's not always possible to put your studio monitors right next to a table using suitable stands. The Gravity SP 3102 is the solution to this problem. The flexible, powder-coated steel stand squeezes onto pretty much any desk. The edge of the solid base is only 25 cm in length. Monitor boxes weighing up to 25 kg can be flexibly positioned at the height you want, and EVA padding and tilting protection make it possible to vertically angle them by up to 15° and horizontally rotate them 360°, meaning you can always find the perfect position for your studio monitors. The colourful G-rings make a clear design statement and can be swapped out in mere seconds. An additional black ring set is also supplied with the product.
Product type
Stands and Tripods
Tubing surface
Powder-coated
Bearing surface
240 x 250 mm , EVA padded
Height adjustment
Adjusting screw
Interchangeable rings
1 x 20 mm , 1 x 30 mm
Black ring pack included
Yes
|
Mastering and mixing professionals usually listen to music in ideal conditions in control rooms specifically designed for mastering and mixing. Studio monitors are either built into the wall or installed on expensive stands positioned just far enough away from studio furniture so that nobody can accidentally bump into them. In day-to-day life, however, most musicians, producers, podcasters, etc., put their monitors right on the table. Not because this is the best solution, but because there's not enough space available.
Even if you invest in a good table stand in this case, you still have to live with the fact that people might walk by or carelessly move the entire structure and destroy your optimum listening set-up. Regular stands for studio monitors also need a lot of room on the table due to their lower base plate.
Gravity® has tackled all these problems with the SP 3102 TM. The studio monitor stand features a table clamp to securely and safely attach the structure to tables with tabletops no thicker than 100 mm. Just like other Gravity® products, it can be tightened using a sturdy and handy knob. In contrast to conventional table stands which require a large base plate to not budge, SP 3102 TM's clamp base is only 10 × 7 cm and does not take up more space than a standard screen holder. The design of the studio monitors stands ensures that they do not stick too far out off the table. This ensures a greater distance between the listener and monitors even when tables aren't that deep, as well as the perfect speaker placement to find the sweet spot in the room.
Everything stays put with the SP 3102 TM thanks to its clamp that keeps stands fixed in position. In addition, the SP 3102 TM is fully equipped to help you perfectly align the monitors into the listening position. The stand has clearly visible markings to adjust the height, rotation, and tilt. There's also EVA padding and an anti-tipping device to make sure your valuable monitors rest securely on the upper shelf, even when tilted up to 15°. You can now sit back and enjoy the sweet spot!
Product type
Stands and Tripods
Tubing surface
Powder-coated
Bearing surface
240 x 250 mm , EVA padded
Height adjustment
Adjusting screw
Base edge length
100X70 mm
Interchangeable rings
1 x 15 mm , 2 x 30 mm
Black ring pack included
Yes
|
Reviews
There are no reviews yet.