Content |
100V line amplifiers with an integral mixer in a half width 2U housing. Inputs for microphones and line input are governed by front panel volume controls with a mixed line output. Mono output to either 100V line or 8 ohms speaker load is connected via a screw terminal connector on the rear panel. Providing cost-effective public address in small to medium installations.
Inputs for microphones and auxiliary line
100V or 8 Ohms operation
Version | 30W, 2 mic | Output power | 30Wrms | Frequency response : line | 91Hz - 38kHz | Frequency response : mic | 93Hz - 16.3kHz | Mic inputs | 2 x 6.3mm jack (unbalanced) | Input sensitivity : line | -8dB | Input sensitivity : mic | -47.5dB | Signal to noise ratio : line | 79dB | Signal to noise ratio : mic | 73dB | Dimensions | 255 x 220 x 84mm | Weight | 3.37kg |
|
P-120D features 2x 200W into 4 Ohm load. This amplifier matches the needs for noiseless operation through air-cooling. It is ideally suitable in studios, small theatres, cabarets, churches, conference- and multimedia rooms etc. Multiple protection circuits care for stable operation. The amplifier is rackmountable (2 units). The optional transformer LT-101 converts the input to a balanced transformer isolated input. |
XB Series - Intelligent Power
Power Without Compromises. The XV is designed for paging, music and alarm signals. Versatile, dynamic and extremely rugged according to IEC286-3. For the highest requirements in safety and quality. Sequential power on, alive contacts and incorporated ground fault detection - the XV is the solution under all conditions. Without the need for additional equipment. For uninterrupted and troublefree operation. Needless to say that the Bittner High-End toroidal output transformers in the XV series are some of the best available.
High Tech SMT Design Protection Circuits: DC, LF, HF, Thermal, Short Circuit, Current Limiter, 3 ms Muting Delay PHOENIX High-End Toroidal Output 100V Transformers Ground Fault Detection LED Indicators for POWER, SIGNAL, CLIP, PROTECT, GNDFAULT Temperature controlled, variable speed low noise fans Volume Controls at the back Stereo / Bridged / Parallel Mode Softstart Sequential Remote Power On Alive Contact Ground Lift 3 Years Warranty
TECHNICAL DATA: XV 200: 2x 100 W / 100 V Class: AB Frequency Response: 20 Hz - 20 kHz (0 / -0.3 dB) THD: < 0.07% Signal-to-Noise Ratio: < 101 dB Channel Seperation: > 70 dB Input Sensitivity: +6 dBu Input Clipping: 22 dBu Input Impedance: 20 kOhm Cooling: 2 to 3 fans (temp. reg. variable speed) Weight: 15 kg Dimensions: 2 RU / 483 x 88 x 382 mm (19" x 3.5" x 15“)
|
Specifications Frequency Response (at 1 watt into 4 ohms, 20Hz - 20 kHz) |
+0/–1 dB
| Signal to Noise Ratio (below rated 8-ohm power at 1 kHz, A-weighted) |
100 dB
| Damping Factor (8 ohm): 20 Hz to 400 Hz |
> 500
| Input Stage |
Input is electronically balanced and employs
precision 1% resistors
| AC Line Current |
CDi 1000: 11.50A, CDi 2000: 11.93A, CDi 4000: 11.75A
At idle: Draws no more than 45 watts.
| Crosstalk (below rated power) 20 Hz to 1 kHz |
> 70 dB
| Input Impedance (nominal) |
20 kilohms balanced, 10 kilohms unbalanced
| Load impedance (note: safe with all types of loads)
Dual
Bridge mono |
2–8 ohms
4–16 ohms
| Voltage Gain (at 1 kHz, 8 ohm rated output) |
CDi 1000: 30.5 dB, CDi 2000: 32.9 dB, CDi 4000: 34.2 dB
| Sensitivity (at 8 ohm rated output) |
1.4V
| Maximum Input Signal |
+22 dBu typical
| Operating Temperature |
0° C to 40° C at 95% relative humidity (non-condensing)
| AC Line Voltage and Frequency Configurations Available (± 10%) |
100V, 120V-240V, 50/60 Hz
| Ventilation |
Flow-through ventilation from front to back
| Cooling |
Heat sinks and proportional-speed fan
| Dimensions: Width, Height, Depth (behind mounting surface) |
EIA Standard 19 in. W (EIA RS-310-B)
x 3.5 in. (8.9 cm) H x 12.25 in. (31.1cm) D
| Net Weight, Shipping Weight |
19 lb (8.6kg), 22 lb (10.0 kg)
| |
Multi-purpose, multi-function mixer/power amplifiers specifically designed for maximum versatility and cost-effective high-performance are ideal units for any PA requirement in locations such as schools and offices and other intermediate size environments. A choice of different power outputs are offered as well as functions such as paging and dual zone coverage.
Specification | |
Power Source |
AC mains 50/60Hz, or 24V DC (M4 screw terminal) |
Output |
120W |
Power Consumption |
AC operation: 158W (rated output), 66W (EN60065) 24V DC operation: 7.0A (rated output), 2.8A (EN60065) |
Frequency Response |
50 - 20,000Hz ±3dB |
Distortion |
Under 2% at 1kHz, rated power |
Input |
MIC 1: -60dB*, 600Ω, electronically-balanced, combined type of XLR-3-31 equivalent and phone jack DIN socket (5 pins) MIC 2, 3: -60dB(*1), 600Ω, electronically-balanced, combined type of XLR-3-31 Equivalent and phone jack AUX 1(MOH): -20dB*, 10kΩ, unbalanced RCA pin jack AUX 2: -20dB(*1), 10kΩ, unbalanced, RCA pin jack AUX 3: -20dB(*1), 10kΩ, unbalanced, RCA pin jack combined type of XLR-3-31 and phone jack TEL(*2): -20dB*1, 10kΩ, electronically-balanced, M3 screw terminal |
Output |
REC: 0dB(*1), 600Ω, unbalanced, RCA pin jack LINE 1,2(*3): 0dB(*1), 600Ω, unbalanced, RCA pin jack MOH: 0dB(*1), 600Ω transformer balanced, M3 screw terminal SPEAKER SELECTOR: 2 zone, high impedance (100V line/83Ω), individual selector switch, M4 screw terminal DIRECT SPEAKER OUT: High impedance (100V line/83Ω),M4 screw terminal Low impedance (4 - 16Ω), M4 screw terminal(Both Low and High impedance terminals cannot be used at the same time.) |
Phantom Power |
ON or OFF for each MIC 1 - 3 with switch setting |
S/N ratio (Band Pass: 20 - 20,000Hz) |
Over 100dB (Master volume: min) Over 76dB (Master volume: max) Over 60dB (MIC 1 - 3)) Over 76dB (AUX 1 - 3) Over 90dB (TEL) Over 96dB (EMERGENCY) |
Control Input |
Bass: ±10dB at 100Hz, Treble: ±10dB at 10kHz TEL: No-voltage make contact input, open voltage: 24V DC, short-circuit: under 5mA, M3 screw terminal EMERGENCY (*4): No-voltage make contact input, open voltage: 24V DC, short-circuit: under 10mA, M3 screw terminal |
Control Output |
Power remote: Open collector output, withstand voltage: 35V DC, control current: under 50mA, M3 screw terminal |
Indicator |
5 point LED output level meter, Power indicator LED, Zone indicator LED, Emergency LED, TEL LED |
Priority |
EMERGENCY: Overrides other inputs TEL: Overrides other inputs except "EMERGENCY”, ON/OFF selectable with switch setting MIC 1: Overrides other inputs except "EMERGENCY & TEL”, ON/OFF selectable with switch setting |
Operating Temperature |
-10ºC - +40ºC |
Finish |
Panel: ABS resin, black, hair line Case: Steel plate, black |
Dimensions |
420 (W) x 107.7 (H) x 367 (D)mm |
Weight |
12.6kg |
Accessory |
Power cord x 1, Terminal block cover x 1, Terminal block cover mounting screw x 2 |
Option |
Rack mounting bracket: MB-25B, Volume control cover: YA-920, Input transformer: IT-453A |
Note* |
(*1) 0dB = 1V (*2) Can be transformer-balanced with the addition of optional IT-453A input transformer. (*3) LINE 1 and LINE 2 outputs can be interlocked with ZONE 1 and ZONE 2 speaker selectors, respectively. (This function needs internal modification.) (*4)Operation when activated can be selected from the following: Turning ON the unit\'s power (factory-preset) or OFF. (The OFF function needs internal modification.) |
|
| - SPEAKER SELECT(5ZONE SPEAKER OUTPUT) Six speaker select switches enable you to select any combination of up to five speakers. - SELECTABLE PRIORITY MUTING Switchable audio signal priority for MIC Channels 1, siren, Chime and Telephone input over other input sources. - MONITOR SPEAKER You can monitor output signal by using the monitor speaker, and can control the monitor level on front panel by 3 step lever switch. - ANNOUNCEMENT CHIME Convenient four-tone chime for use with announcements. - REMOTE CONTROL INPUT Individual speaker zones can be selected and chime can be operated by wired remote control. - EM(EMERGENCY) When EM switch is pressed in emergencies, EM broadcasting stored in VOICE IC is outputted. - REMOTE POWER You can turn on/off amplifier by remote control. - INDIVIDUAL INPUT GAIN CONTROLS Rear-panel gain controls for each input channel for total control of individual levels. - MODULAR DESIGN Optional modules can be installed in multiple configurations for convenience and ease of use. Choose the PAM-CDA (Compact Disc), PAM-T (AM/FM Tuner) or PAM-D (Cassette Deck) modules to expand the PAM-510/520ʼs audio capabilities. ACCESSORIES One detachable AC power cord is provided for use with this product. | | | | | | PAM-510 | PAM-520 | Amplifier Section (Amp In@1kHz, 4Ω Load Output) | Rated Output Power (THD 1%) | 120W(RMS) | 240W(RMS) | Speaker Zone 1~5 Output | 25W MAX | 50W MAX | Input Sensitivity/Impedance | 1V/20kΩ | S/N | Better than 85dB | Frequency Response (at 1kHz Half Power Output, ±3dB) | 80Hz~18kHz | Mic Input Section (Mic 1~4 In@1kHz, Preamp Out) | Input Sensitivity/Impedance | –60dBV/600Ω | S/N | Better than 55dB | Frequency Response (±3dB) | 120Hz~10kHz | Tone Control (Bass:100Hz,Treble:10kHz) | ±12dB | Phantom Power | +24VDC | Line Input Section (Line 1~2 In@1kHz, Preamp Out) | Input Sensitivity/Impedance | –30dBV/10kΩ | S/N | Better than 65dB | Frequency Response (±3dB) | 80Hz~15kHz | Tone Control (Bass:100Hz,Treble:10kHz) | ±12dB | Remote Amp Section (Remote In@1kHz, Preamp Out) | Mic Input Sensitivity/Impedance | –60dBV/600Ω | S/N | Better than 55dB | Frequency Response (±3dB) | 120Hz~10kHz | Tel In Section (Tel In@1kHz, Preamp Out) | Input Sensitivity/Impedance | 0.3V/600Ω(USA/Canada) | 0.775V/600Ω(EC & Associated) | S/N | Better than 65dB | Frequency Response (±3dB) | 330Hz~3kHz | Pre Amp Out(Mic 1~4, Line 1~2, Tel In, Remote In) | 0dBV/600Ω | | T.H.D | Less than 0.5% | Record Out | –10dBV/3kΩ | Operating Temperature | –10°C~40°C | Power Source | 100–120VAC or 220–240VAC; 50/60Hz, 24VDC | Power Consumption (1/8 POWER) | 180W | 320W | Weight | 17kg/37.6lb | 19kg/42lb | Dimensions | 482(W) x 132(H) x 398(D)mm 19(W) x 5.2(H) x 15.7(D)in | ※ Specifications and design subject to change without notice. | | | |
|
Reviews
There are no reviews yet.