| Content |
100V line amplifiers with an integral mixer in a half width 2U housing. Inputs for microphones and line input are governed by front panel volume controls with a mixed line output. Mono output to either 100V line or 8 ohms speaker load is connected via a screw terminal connector on the rear panel. Providing cost-effective public address in small to medium installations.
Inputs for microphones and auxiliary line
100V or 8 Ohms operation
| Version | 60W, 3 mic | | Output power | 60Wrms | | Frequency response : line | 91Hz - 48kHz | | Frequency response : mic | 93Hz - 15.0kHz | | Mic inputs | 3 x 6.3mm jack (unbalanced) | | Input sensitivity : line | -8.8dB | | Input sensitivity : mic | -50.1dB | | Signal to noise ratio : line | 90dB | | Signal to noise ratio : mic | 82dB | | Dimensions | 285 x 220 x 84mm | | Weight | 4.35kg |
|
Multi-purpose, multi-function mixer/power amplifiers specifically designed for maximum versatility and cost-effective high-performance are ideal units for any PA requirement in locations such as schools and offices and other intermediate size environments. A choice of different power outputs are offered as well as functions such as paging and dual zone coverage.
| Specification | |
|---|
| Power Source |
AC mains 50/60Hz, or 24V DC (M4 screw terminal) |
| Output |
120W |
| Power Consumption |
AC operation: 158W (rated output), 66W (EN60065)
24V DC operation: 7.0A (rated output), 2.8A (EN60065) |
| Frequency Response |
50 - 20,000Hz ±3dB |
| Distortion |
Under 2% at 1kHz, rated power |
| Input |
MIC 1: -60dB*, 600Ω, electronically-balanced, combined type of XLR-3-31 equivalent and phone jack DIN socket (5 pins)
MIC 2, 3: -60dB(*1), 600Ω, electronically-balanced, combined type of XLR-3-31 Equivalent and phone jack
AUX 1(MOH): -20dB*, 10kΩ, unbalanced RCA pin jack
AUX 2: -20dB(*1), 10kΩ, unbalanced, RCA pin jack
AUX 3: -20dB(*1), 10kΩ, unbalanced, RCA pin jack combined type of XLR-3-31 and phone jack
TEL(*2): -20dB*1, 10kΩ, electronically-balanced, M3 screw terminal |
| Output |
REC: 0dB(*1), 600Ω, unbalanced, RCA pin jack
LINE 1,2(*3): 0dB(*1), 600Ω, unbalanced, RCA pin jack
MOH: 0dB(*1), 600Ω transformer balanced, M3 screw terminal
SPEAKER SELECTOR:
2 zone, high impedance (100V line/83Ω), individual selector switch, M4 screw terminal
DIRECT SPEAKER OUT:
High impedance (100V line/83Ω),M4 screw terminal
Low impedance (4 - 16Ω), M4 screw terminal(Both Low and High impedance terminals cannot be used at the same time.) |
| Phantom Power |
ON or OFF for each MIC 1 - 3 with switch setting |
S/N ratio
(Band Pass: 20 - 20,000Hz) |
Over 100dB (Master volume: min)
Over 76dB (Master volume: max)
Over 60dB (MIC 1 - 3))
Over 76dB (AUX 1 - 3)
Over 90dB (TEL)
Over 96dB (EMERGENCY) |
| Control Input |
Bass: ±10dB at 100Hz, Treble: ±10dB at 10kHz
TEL: No-voltage make contact input, open voltage: 24V DC, short-circuit: under 5mA, M3 screw terminal
EMERGENCY (*4): No-voltage make contact input, open voltage: 24V DC, short-circuit: under 10mA, M3 screw terminal |
| Control Output |
Power remote: Open collector output, withstand voltage: 35V DC, control current: under 50mA, M3 screw terminal |
| Indicator |
5 point LED output level meter, Power indicator LED, Zone indicator LED, Emergency LED, TEL LED |
| Priority |
EMERGENCY: Overrides other inputs
TEL: Overrides other inputs except "EMERGENCY”, ON/OFF selectable with switch setting
MIC 1: Overrides other inputs except "EMERGENCY & TEL”, ON/OFF selectable with switch setting |
| Operating Temperature |
-10ºC - +40ºC |
| Finish |
Panel: ABS resin, black, hair line
Case: Steel plate, black |
| Dimensions |
420 (W) x 107.7 (H) x 367 (D)mm |
| Weight |
12.6kg |
| Accessory |
Power cord x 1,
Terminal block cover x 1,
Terminal block cover mounting screw x 2 |
| Option |
Rack mounting bracket: MB-25B,
Volume control cover: YA-920,
Input transformer: IT-453A |
| Note* |
(*1) 0dB = 1V
(*2) Can be transformer-balanced with the addition of optional IT-453A input transformer.
(*3) LINE 1 and LINE 2 outputs can be interlocked with ZONE 1 and ZONE 2 speaker selectors, respectively. (This function needs internal modification.)
(*4)Operation when activated can be selected from the following: Turning ON the unit\'s power (factory-preset) or OFF. (The OFF function needs internal modification.) |
|
XB Series - Intelligent Power
Power Without Compromises.
The XV is designed for paging, music and alarm signals. Versatile, dynamic and
extremely rugged according to IEC286-3. For the highest requirements in safety
and quality.
Sequential power on, alive contacts and incorporated ground fault detection -
the XV is the solution under all conditions. Without the need for additional equipment.
For uninterrupted and troublefree operation.
Needless to say that the Bittner High-End toroidal output transformers in the XV
series are some of the best available.
High Tech SMT Design
Protection Circuits: DC, LF, HF, Thermal, Short Circuit, Current Limiter, 3 ms Muting Delay
PHOENIX
High-End Toroidal Output 100V Transformers
Ground Fault Detection
LED Indicators for POWER, SIGNAL, CLIP, PROTECT, GNDFAULT
Temperature controlled, variable speed low noise fans
Volume Controls at the back
Stereo / Bridged / Parallel Mode
Softstart
Sequential Remote Power On
Alive Contact
Ground Lift
3 Years Warranty
TECHNICAL DATA:
XV 400: 2x 200 W / 100 V
Class: AB
Frequency Response: 20 Hz - 20 kHz (0 / -0.3 dB)
THD: < 0.07%
Signal-to-Noise Ratio: < 101 dB
Channel Seperation: > 70 dB
Input Sensitivity: +6 dBu
Input Clipping: 22 dBu
Input Impedance: 20 kOhm
Cooling: 2 to 3 fans (temp. reg. variable speed)
Weight: 17 kg
Dimensions: 2 RU / 483 x 88 x 382 mm (19" x 3.5" x 15“) |
Toa A1806 powered mixer is a basic mono/2 zones 60 Watts (100V) PA amplifier with 3 mic channels suited for broadcasting, paging or background music in schools, offices or shops.
| | | Weight (KG) | 9.4 | | Size (mm) | 420 x 107.7 x 367 | | Colour | Black | | Manufacturer warranty (UK) | 1 year RTB |
|
The Crown 135MA is a high value mixer-amplifier for commercial audio. It provides 8-ohm and constant-voltage outputs (70V and 100V). Typical uses are paging, background music, and music-on-hold. The 135MA provides 3 inputs (each with a volume control) and a 35W amplifier output. Other features include priority muting, voice activated muting, phantom power, and Bass and Treble controls.
Features
- 3 inputs (each with a volume control), and one 35W amplifier output channel
- Ideal for paging, background music, and music-on-hold
- Balanced Phoenix-type mic/line input, telephone output, dual RCA stereo music inputs, screw-terminal speaker outputs
- Priority muting by VOX or external switch
- Bass and Treble controls on master output
- Three-Year, No-Fault, Fully Transferable Warranty completely protects your investment and guarantees its specifications
Specifications
- Minimum Guaranteed Power into 8 ohms or 70V/100V Output: 35W
- Frequency Response (at 1 watt from line out): 50Hz to 20kHz +/-1dB; 19Hz to 34kHz +0, -3dB
- Signal to Noise Ratio (ref. to rated power, master volume at minimum):
Mic: > 58 dB.
Line: > 60 dB.
Telephone: > 60 dB.
Inputs 2 or 3 (and 4 in 160MA): > 78 dB - THD+N:
|
Specifications | Frequency Response (at 1 watt into 4 ohms, 20Hz - 20 kHz) |
+0/–1 dB
| | Signal to Noise Ratio (below rated 8-ohm power at 1 kHz, A-weighted) |
100 dB
| | Damping Factor (8 ohm): 20 Hz to 400 Hz |
> 500
| | Input Stage |
Input is electronically balanced and employs
precision 1% resistors
| | AC Line Current |
CDi 1000: 11.50A, CDi 2000: 11.93A, CDi 4000: 11.75A
At idle: Draws no more than 45 watts.
| | Crosstalk (below rated power) 20 Hz to 1 kHz |
> 70 dB
| | Input Impedance (nominal) |
20 kilohms balanced, 10 kilohms unbalanced
| Load impedance (note: safe with all types of loads)
Dual
Bridge mono |
2–8 ohms
4–16 ohms
| | Voltage Gain (at 1 kHz, 8 ohm rated output) |
CDi 1000: 30.5 dB, CDi 2000: 32.9 dB, CDi 4000: 34.2 dB
| | Sensitivity (at 8 ohm rated output) |
1.4V
| | Maximum Input Signal |
+22 dBu typical
| | Operating Temperature |
0° C to 40° C at 95% relative humidity (non-condensing)
| | AC Line Voltage and Frequency Configurations Available (± 10%) |
100V, 120V-240V, 50/60 Hz
| | Ventilation |
Flow-through ventilation from front to back
| | Cooling |
Heat sinks and proportional-speed fan
| | Dimensions: Width, Height, Depth (behind mounting surface) |
EIA Standard 19 in. W (EIA RS-310-B)
x 3.5 in. (8.9 cm) H x 12.25 in. (31.1cm) D
| | Net Weight, Shipping Weight |
19 lb (8.6kg), 22 lb (10.0 kg)
| |
Reviews
There are no reviews yet.