| Content |
100V line amplifiers with an integral mixer in a half width 2U housing. Inputs for microphones and line input are governed by front panel volume controls with a mixed line output. Mono output to either 100V line or 8 ohms speaker load is connected via a screw terminal connector on the rear panel. Providing cost-effective public address in small to medium installations.
Inputs for microphones and auxiliary line
100V or 8 Ohms operation
| Version | 60W, 3 mic | | Output power | 60Wrms | | Frequency response : line | 91Hz - 48kHz | | Frequency response : mic | 93Hz - 15.0kHz | | Mic inputs | 3 x 6.3mm jack (unbalanced) | | Input sensitivity : line | -8.8dB | | Input sensitivity : mic | -50.1dB | | Signal to noise ratio : line | 90dB | | Signal to noise ratio : mic | 82dB | | Dimensions | 285 x 220 x 84mm | | Weight | 4.35kg |
| - Easy installation in practically any 12V battery equipped car.
- Compact, rugged construction and front panel controls.
- Two phone jack mic. inputs and handy phone jack AUX input for external equipment connection.
- Unidirectional dynamic microphone with talk switch.
| Specification |
|
|---|
| Power Source | Standard voltage: 14VDC
Usable Voltage; 10 ~ 16V DC (12V Battery Used) | | Power Consumption | 2.2A or less at rated power output. | | Output Power | Rated 15W, max. 35W | | Output Impedance | 4Ω (BRN), 8Ω (ORG), COmmon (WHT)
Changeable by changing lead wire connections. | | Distortion | Less than 5% (at 1kHz rated output) | | Frequency Response | 100 ~ 10,000Hz | | Input | Mic 1, 2 : 600Ω, 4 mV, Phone Jack
Aux : 10 kΩ, 500 mV, Phone Jack | | Dimensions | (W x H x D): 178 x 50 x 132mm (mounting device excluded) | | Weight | 900g | | Finish | Front panel; ABS resin, Black
Case; Zinc plated steel sheet | | Accessory | Microphone holder ... 1
Mounting Bracket ... 1
Mounting Screw ... 1
Fuse (4A) ... 1
Connection cord ... 1 set | | Accessory | Microphone Unidirectional dynamic type with Talk switch
Impedance : 600Ω
Sensitivity : -53dB (IkHz, 0 dB = 1 V / Pa) |
|
XB Series - Intelligent Power
Power Without Compromises.
The XV is designed for paging, music and alarm signals. Versatile, dynamic and
extremely rugged according to IEC286-3. For the highest requirements in safety
and quality.
Sequential power on, alive contacts and incorporated ground fault detection -
the XV is the solution under all conditions. Without the need for additional equipment.
For uninterrupted and troublefree operation.
Needless to say that the Bittner High-End toroidal output transformers in the XV
series are some of the best available.
High Tech SMT Design
Protection Circuits: DC, LF, HF, Thermal, Short Circuit, Current Limiter, 3 ms Muting Delay
PHOENIX
High-End Toroidal Output 100V Transformers
Ground Fault Detection
LED Indicators for POWER, SIGNAL, CLIP, PROTECT, GNDFAULT
Temperature controlled, variable speed low noise fans
Volume Controls at the back
Stereo / Bridged / Parallel Mode
Softstart
Sequential Remote Power On
Alive Contact
Ground Lift
3 Years Warranty
TECHNICAL DATA:
XV 400: 2x 200 W / 100 V
Class: AB
Frequency Response: 20 Hz - 20 kHz (0 / -0.3 dB)
THD: < 0.07%
Signal-to-Noise Ratio: < 101 dB
Channel Seperation: > 70 dB
Input Sensitivity: +6 dBu
Input Clipping: 22 dBu
Input Impedance: 20 kOhm
Cooling: 2 to 3 fans (temp. reg. variable speed)
Weight: 17 kg
Dimensions: 2 RU / 483 x 88 x 382 mm (19" x 3.5" x 15“) |
Specifications | Frequency Response (at 1 watt into 4 ohms, 20Hz - 20 kHz) |
+0/–1 dB
| | Signal to Noise Ratio (below rated 8-ohm power at 1 kHz, A-weighted) |
100 dB
| | Damping Factor (8 ohm): 20 Hz to 400 Hz |
> 500
| | Input Stage |
Input is electronically balanced and employs
precision 1% resistors
| | AC Line Current |
CDi 1000: 11.50A, CDi 2000: 11.93A, CDi 4000: 11.75A
At idle: Draws no more than 45 watts.
| | Crosstalk (below rated power) 20 Hz to 1 kHz |
> 70 dB
| | Input Impedance (nominal) |
20 kilohms balanced, 10 kilohms unbalanced
| Load impedance (note: safe with all types of loads)
Dual
Bridge mono |
2–8 ohms
4–16 ohms
| | Voltage Gain (at 1 kHz, 8 ohm rated output) |
CDi 1000: 30.5 dB, CDi 2000: 32.9 dB, CDi 4000: 34.2 dB
| | Sensitivity (at 8 ohm rated output) |
1.4V
| | Maximum Input Signal |
+22 dBu typical
| | Operating Temperature |
0° C to 40° C at 95% relative humidity (non-condensing)
| | AC Line Voltage and Frequency Configurations Available (± 10%) |
100V, 120V-240V, 50/60 Hz
| | Ventilation |
Flow-through ventilation from front to back
| | Cooling |
Heat sinks and proportional-speed fan
| | Dimensions: Width, Height, Depth (behind mounting surface) |
EIA Standard 19 in. W (EIA RS-310-B)
x 3.5 in. (8.9 cm) H x 12.25 in. (31.1cm) D
| | Net Weight, Shipping Weight |
19 lb (8.6kg), 22 lb (10.0 kg)
| |
The VP-200VX Power Amplifier Input Module is designed to be used in conjunction with the VP-2064, VP-2122, VP-2241 or VP-2421 power amplifier.
| Power Source | Supplied from VP-2064, VP-2122, VP-2241 or VP-2421 | | Current Consumption | 30 mA or less | | Power Amplifier Link | RJ45 female connector for connecting the VX-200SP,
VX-200SZ Audio Output module, or SX-2100AO.
Twisted-pair straight cable (TIA/EIA-568A standard) | | Finish | Panel: Surface-treated steel plate | | Dimensions | 88 (W) × 25.8 (H) × 53.2 (D) mm | | Weight | 50 g | | Applicable Model | VP-2064, VP-2122, VP-2241, VP-2421 |
|
XB Series - Intelligent Power
Power Without Compromises.
The XV is designed for paging, music and alarm signals. Versatile, dynamic and
extremely rugged according to IEC286-3. For the highest requirements in safety
and quality.
Sequential power on, alive contacts and incorporated ground fault detection -
the XV is the solution under all conditions. Without the need for additional equipment.
For uninterrupted and troublefree operation.
Needless to say that the Bittner High-End toroidal output transformers in the XV
series are some of the best available.
High Tech SMT Design
Protection Circuits: DC, LF, HF, Thermal, Short Circuit, Current Limiter, 3 ms Muting Delay
PHOENIX
High-End Toroidal Output 100V Transformers
Ground Fault Detection
LED Indicators for POWER, SIGNAL, CLIP, PROTECT, GNDFAULT
Temperature controlled, variable speed low noise fans
Volume Controls at the back
Stereo / Bridged / Parallel Mode
Softstart
Sequential Remote Power On
Alive Contact
Ground Lift
3 Years Warranty
TECHNICAL DATA:
XV 200: 2x 100 W / 100 V
Class: AB
Frequency Response: 20 Hz - 20 kHz (0 / -0.3 dB)
THD: < 0.07%
Signal-to-Noise Ratio: < 101 dB
Channel Seperation: > 70 dB
Input Sensitivity: +6 dBu
Input Clipping: 22 dBu
Input Impedance: 20 kOhm
Cooling: 2 to 3 fans (temp. reg. variable speed)
Weight: 15 kg
Dimensions: 2 RU / 483 x 88 x 382 mm (19" x 3.5" x 15“)
|
Reviews
There are no reviews yet.