| Content |
- Aftermarket diaphragm D8R2406 replacement for the JBL 2406H-1 Driver or BMS 4538 and more models.
- Fits JBL MPRO 400 Series
- 8 Ohm
Polymer diaphragm replacement kit: 8ohm, 37.8mm (voice coil inner diameter)* 70.0mm (al ring outer diameter),aluminum round wire v/c
This aftermarket diaphragm is a direct replacement for the JBL 2406, 2406H, 2406-1, 2406H-1 driver / tweeter / horn.
Specifications
- Annular Ring Diaphragm
- 8 ohm
- Peak power 300 watts
- Frequency range 1200Hz - 30kHz
- Overall diaphragm diameter 2.75-in or 70-mm
- Voice coil diameter 1.5-in or 38-mm
- Diaphragm material is polyester
- Voice coil former is Kapton
- Voice coil wire is edge wound / flat wound, aluminum
Very easy to replace. This diaphragm self aligns. Simply remove the old diaphragm,
clean the voice coil gap with a piece of masking tape, then install the new diaphragm in
reverse order.
This diaphragm uses the polyester annular ring diaphragm and surround just like the
original JBL diaphragm.
This diaphragm will handle the same amount of power, and sounds the same as the
original JBL 2406 diaphragm, guaranteed! | Replacement diaphragm kit for RX™22 driver
Impulse 1012 8 Ohm, Impulse 1012 4 Ohm, Impulse 1012P,Impulse 1015 8 Ohm, Impulse 1015 4 Ohm, DJS4, DJS 5, SP2X, SP3X,SP4X, SP5X, SP5XL, SP6X, SP112MX, SP115MX Impulse 1015P, QW 3, QW 3F, TLS 6X, SP2, SP3, SP4, SP5, SP6, SP12M, SP15M, SP 8
- Peavey Factory Speaker RX22, 22XT, 22XT+ Original Diaphragm Part # 00452400
- NEW! Now used for ALL 22 series drivers: RX22, 22A, 22XT, 22XT+
- Voice coil: 2" (50mm)
- Diameter: 4-1/2" (115mm)
- Impedance: 8 ohm
- Titanium dome with edge wound copper clad aluminum voice coil on high temp composite bobbin
- Installation instructions, Ferro Fluid, and new mounting bolts included on new diaphragms starting mid 2015Please check your model before ordering to make sure you are getting the correct diaphragm.
| JBL D16R2408 Genuine Diaphragm for 2408H 16 Ohm
This genuine JBL replacement diaphragm is compatible with the 2408H horn driver. JBL part number D16R2408.
This driver has been used in many JBL cabinets. |
- Voice coil: 3.93″ (100mm)
- Diameter: 5″ (127mm)
- Impedance: 8 ohm, DCR: 4.7 ohm
- Titanium ribbed dome with edge wound voice coil on Nomex former
- We sell an aftermarket version of this diaphragm. See our aftermarket diaphragms page for details.
- Please check your model before ordering to make sure you are getting the correct diaphragm.
- See the “Fits Models” tab for all applicable cabinet and driver numbers.
| Original diaphragm d-30d replacement spare part for TOA TU-630/650, TC-303 |
-
JBL Factory Speaker Diaphragm Part # D8R2418
-
Voice coil: 1-3/4" (45mm)
-
Diameter: 3" (75mm)
-
Length: 5-1/8" (130mm)
-
Impedance: 8 ohm, DCR: 4 ohm
-
Titanium dome with copper voice coil on Kapton former.
-
Fits JBL Driver and Cabinet Models:
JBL: 2418, JBL 2418H, JBL 2418H-1, 3622N, 3632M-HF, 3632M-HF-T, 3677S, 3722HF, 3722N-HF, 4425LR, AC2212/00-WH, AC2215/00-WH, CAB-55, CAB55, CAB 55, EON-15, EON15, EON 15, EON 15P-1/230, EON POWER15, EON-15-G2, EON15-G2, EON 15-G2, EON-15P, EON15P, EON 15P, MR-902, MR902, MR 902, ,MR-905, MR905, MR 905, MR-922, MR922, MR 922, MR-925, MR925, MR 925, MR-926, MR926, MR 926, MR-935, MR935, MR 935, MR-938, MR938, MR 938, MS-112-WH, MS112-WH, MS 112-WH, MS-115-WH, MS115-WH, MS 115-WH, and many more!
Please check your model before ordering to make sure you are getting the correct diaphragm.
|
Reviews
There are no reviews yet.