ALPHATON DI 1000 TUBE D.I BOX

773.75 incl. GR VAT

In stock

EAN: N/A
Installments calculation
CompareAdd to wishlist Submit Better Price
Availability: Available in 1-3 d. Available in 1-3 d. SKU: DI 1000 Category:
Tube-buffered DI-Box DI-1000 The Tube-Buffered DI-Box DI-1000 allows the extraction of all the musical details of musical interfaces without degrading the sound. This can only be achieved by providing a very high input impedance to avoid any loading of instrument pickups.This design approach allows seemingly infinite headroom to preserve the real dynamic range of the […]

 

Read more

Tube-buffered DI-Box DI-1000

The Tube-Buffered DI-Box DI-1000 allows the extraction of all the musical details of
musical interfaces without degrading the sound. This can only be achieved by
providing a very high input impedance to avoid any loading of instrument pickups.This
design approach allows seemingly infinite headroom to preserve the real dynamic range
of the interfaced instruments.A vacuum tube enables all these goals to be achieved
without any compromises in sound quality.The sonic difference between a standard
DI-Box and the Tube-Buffered DI-Box is comparable to the musical resolution difference
between a standard microphone and a studio microphone.One of the best transformers,
the very transparent sounding JENSEN JT-DB-E, was chosen providing complete ground
isolation. The parameters of this transformer, like frequency response, phase response,
group delay and geadroom capabilities, play a vital part in the performance of this DI-Box.
 
Technical Specifications
Input
The signal of the instrument is directly fed to the tube circuit with > 20 MOhms input
impedance to prevent any signal degradation, inevitable in traditional designs.
Buffered Output“
The second stage of the vacuum tube is used to buffer the signal and lower the output
impedance to < 8 kOhms. This unity gain output allows for cable runs of 10 meters
without loosing high frequency information.
Boost circuit
The boost circuit increases the signal send to the output transformer by 15 dB. This may
be useful for instruments with extremely low output, but decreases headroom capability
to 6 Volt rms. Under these circumstances the signal may be clipped, concerning the output
transformer?s signal, which gives you 2nd harmonic tube-like distortion. This distortion
normally does not occur – but is sometimes desirable, being the reason for this special feature.
Unity circuit
The unity circuit feeds a low distortion unity gain signal to the JENSEN output transformer.
This gives the best possible sound quality.
Ground-lift“-Switch
This front panel mounted switch allows complete ground and electrical isolation between the
direct injection box and the console or recording device.
 

Mechanical Specifications
Cabinet 2 mm stainless steel
Front- and rear-panel 1,5 mm stainless steel lasercut and photo-chemically etched
Dimensions 185 x 100 x 40 mm
Vibration insulation 4 high-compliance rubber-elements
Operating Voltage
220/110 V AC, selectable via rear panel mounted switch. The fuse is easily
accessible from the rear panel. IEC mains connector with optional fixture.
Construction details
Double sided glass fibre contacted PCB with 70 mm copper plating. 1% metal film resistors
and the finest polypropylene capacitors are used in the signal path. MIL type Switchcraft jacks
and high performance switches ensure flawless operation. The power supply is optimised via
measurement quality toroid transformer and a low impedance design to ensure the lowest
possible noise. Through a double sided PCB all parts are roadworthy secured. A waterclear
blue LED perfects the aesthetics of the DI box.

Technical Data
Input impedance > 20 MOhm
Output impedance180 Ohm at 1 kHz
Frequncy response 20 Hz – 20 kHz (-0,1 dB)
                             5 Hz – 120 kHz (-3 dB)
THD at 0 dBv  0,06% at 20 Hz
                      0,04% at 1 kHz
                      0,035% at 20 kHz
Signal to Noise Ratio 86 dB
Tube ECC 83/7025 A – military E 83 CC optional
Output transformer JENSEN JT-DB-E
Polarity Pin 2 Hot , AES/IEC -Standard
Max. Input voltage > 30 V peak
 

Weight 0.60 kg

Reviews

There are no reviews yet.

Be the first to review “ALPHATON DI 1000 TUBE D.I BOX”

Your email address will not be published. Required fields are marked *

Quick Comparison

ALPHATON DI 1000 TUBE D.I BOX removeSTEWART ADB4-4 CH. ACTIVE D.I BOX removePALMER PAN03 AUDIO TOOLS Active x 4ch DI box 19" Rack removePALMER AUDIO PAN02 TOOLS Active DI-box removeBSS AR-133 ACTIVE DI BOX (Battery/ Phantom Powered) removeARX DI-PLUS 2 STEREO ACTIVE D.I BOX remove
NameALPHATON DI 1000 TUBE D.I BOX removeSTEWART ADB4-4 CH. ACTIVE D.I BOX removePALMER PAN03 AUDIO TOOLS Active x 4ch DI box 19" Rack removePALMER AUDIO PAN02 TOOLS Active DI-box removeBSS AR-133 ACTIVE DI BOX (Battery/ Phantom Powered) removeARX DI-PLUS 2 STEREO ACTIVE D.I BOX remove
Image
SKUDI 1000ADB4EPAN03PAN02AR-133DI-PLUS 2
Rating
Price 773.75 incl. GR VAT 585.13 incl. GR VAT 292.43 incl. GR VAT 68.20 incl. GR VAT 159.00 incl. GR VAT 203.11 incl. GR VAT
Stock

In stock

Available on backorder

Available on backorder

Only 2 left in stock (can be backordered)

Only 5 left in stock (can be backordered)

In stock

AvailabilityIn stockAvailable on backorderAvailable on backorderOnly 2 left in stock (can be backordered)Only 5 left in stock (can be backordered)In stock
Add to cart

Add to cart

Add to cart

Add to cart

Add to cart

Add to cart

Add to cart

Description
Content

Tube-buffered DI-Box DI-1000

The Tube-Buffered DI-Box DI-1000 allows the extraction of all the musical details of
musical interfaces without degrading the sound. This can only be achieved by
providing a very high input impedance to avoid any loading of instrument pickups.This
design approach allows seemingly infinite headroom to preserve the real dynamic range
of the interfaced instruments.A vacuum tube enables all these goals to be achieved
without any compromises in sound quality.The sonic difference between a standard
DI-Box and the Tube-Buffered DI-Box is comparable to the musical resolution difference
between a standard microphone and a studio microphone.One of the best transformers,
the very transparent sounding JENSEN JT-DB-E, was chosen providing complete ground
isolation. The parameters of this transformer, like frequency response, phase response,
group delay and geadroom capabilities, play a vital part in the performance of this DI-Box.
 
Technical Specifications
Input
The signal of the instrument is directly fed to the tube circuit with > 20 MOhms input
impedance to prevent any signal degradation, inevitable in traditional designs.
Buffered Output“
The second stage of the vacuum tube is used to buffer the signal and lower the output
impedance to < 8 kOhms. This unity gain output allows for cable runs of 10 meters
without loosing high frequency information.
Boost circuit
The boost circuit increases the signal send to the output transformer by 15 dB. This may
be useful for instruments with extremely low output, but decreases headroom capability
to 6 Volt rms. Under these circumstances the signal may be clipped, concerning the output
transformer?s signal, which gives you 2nd harmonic tube-like distortion. This distortion
normally does not occur - but is sometimes desirable, being the reason for this special feature.
Unity circuit
The unity circuit feeds a low distortion unity gain signal to the JENSEN output transformer.
This gives the best possible sound quality.
Ground-lift“-Switch
This front panel mounted switch allows complete ground and electrical isolation between the
direct injection box and the console or recording device.
 

Mechanical Specifications
Cabinet 2 mm stainless steel
Front- and rear-panel 1,5 mm stainless steel lasercut and photo-chemically etched
Dimensions 185 x 100 x 40 mm
Vibration insulation 4 high-compliance rubber-elements
Operating Voltage
220/110 V AC, selectable via rear panel mounted switch. The fuse is easily
accessible from the rear panel. IEC mains connector with optional fixture.
Construction details
Double sided glass fibre contacted PCB with 70 mm copper plating. 1% metal film resistors
and the finest polypropylene capacitors are used in the signal path. MIL type Switchcraft jacks
and high performance switches ensure flawless operation. The power supply is optimised via
measurement quality toroid transformer and a low impedance design to ensure the lowest
possible noise. Through a double sided PCB all parts are roadworthy secured. A waterclear
blue LED perfects the aesthetics of the DI box.

Technical Data
Input impedance > 20 MOhm
Output impedance180 Ohm at 1 kHz
Frequncy response 20 Hz - 20 kHz (-0,1 dB)
                             5 Hz - 120 kHz (-3 dB)
THD at 0 dBv  0,06% at 20 Hz
                      0,04% at 1 kHz
                      0,035% at 20 kHz
Signal to Noise Ratio 86 dB
Tube ECC 83/7025 A - military E 83 CC optional
Output transformer JENSEN JT-DB-E
Polarity Pin 2 Hot , AES/IEC -Standard
Max. Input voltage > 30 V peak
 

You're serious about getting rid of all that excess noise on stage, but you've got so many line
instruments you don't know where to start. The ADB-4 from Stewart can take care of all your
high impedance problems. The ADB-4 is 4 active direct boxes, all in a module that only takes
up half a space on your keyboard rack. It's a rugged, durable piece of equipment that packs a
lot of DI power.

? Requires phantom power or 9v battery
? Ground lift switch
? Instrument or speaker level switch
? Transformerless
? Can be used with amp up to 400w
? RF shielding

Palmer PAN 03
19" DI Box 4-Channel active

Active 4-channel DI box. Each channel has a jack input with a parallel output for passing through the signal. An attenuation switch (-30 dB) allows either a line or loudspeaker signal to be connected.Active 4 x DI box, 19" format. Technical specitications identicl to the PAN-02, however, the PAN-03 is built for mains operation. All connections and switches are located on the front panel, an additional parallel XLR output is located in back. 19 inch rack-mount format, 1 rack space, 90 mm front to back.

Product type DI Boxes
Type active
Channels 4
Inputs 4
Input connectors 6.3 mm jack
Max. input level + 45 dBu
Input impedance (@ 60 Hz) 1 M Ohm(s)
Input pad 0 / -30 dB
Outputs 4 (+ 4 parallel XLR outs)
THRU outputs/channel 1
Output connectors 6.3 mm jack , XLR
Max. output level + 10 dBu
Output impedance 600 Ohm(s)
Frequency response 10 - 20000 Hz
Transformer balanced Yes
Ratio 10 : 1
Indicators Power
Controls attenuator , ground lift
Operating voltage external
Cabinet material sheet steel
Cabinet surface Powder coated
Width 480 mm
Width 19 "
Depth 90 mm
Height 45 mm
Height 1 U
Weight 1,6 kg
Standard active DI box. Can be operated with 9 V batteries or 48 V phantom power. High-impedance input; higher output level than with a passive DI box. Active circuitry allows for high input impedance ( 1 meg. ohm) and higher input sensitivity (typical difference between in and out -4 dB). Maximum output impedance with phantom power operation +10 dB. Output: transformer balanced. The special "floating ground" circuitry enables ground lift even during phantom power operation. Metal case 110 x 73 x 42 mm.With added functionality and enhanced audio performance, the AR-133 has been designed to be more affordable for musicians, studios and PA companies. The unit includes phantom power and battery supplies as standard. Should the phantom power from the console fail or be accidentally switched off, the AR-133 automatically switches over to the internal 9V battery providing uninterrupted use. The unit is housed in a rugged aluminium extrusion case, with robust polyurethane end-cheeks which give the AR-133 a very distinctive look. Input connectors are both 1/4" jack sockets and an XLR socket, the latter meaning that the AR-133 can be used to convert unbalanced signals to a balanced output on XLRs throughout. The arched case allows cables to run back underneath the unit from the end for neat cable management. Input attenuation is 0, -20 or -40dB, making the box suitable for instrument, line or amplifier levels on inputs. On the output side, a ground-lift switch is provided for quick solutions to ground-loop problems. The AR-133 uses an enhanced version of the same audio path as the AR-116, now regarded by many people as a reference standard. The sound quality is legendary, particularly on acoustic and bass guitars. Numerous applications can be satisfied by the AR-133. For example, as well as the traditional guitar use, the AR-133 can be used with keyboards, DJ consoles, amplifier outputs, and other electronic sources.An additional bonus is the ability to use the AR-133 as an active balancing device. Input Section Input Impedance  1M Ohm (pad at 0dB) 47k Ohm (pad at -20dB) 47k Ohm (pad at -40dB) Max Input Level +9dBu (pad at 0dB) +29dBu (pad at -20dB) +49dBu (pad at -40dB) Connectors  Two Parallel 1/4" jack connectors and a parallel XLR connector (unbalanced) Jack:  Tip Hot (+ve) Sleeve Ground XLR: Pin 2 Hot (+ve) Pin 1 & 3 Ground Output Section Output Transformer Balanced Max. Output Level  +8dBu into 600 Ohms or greater Connector  XLR3-32 or equivalent System Performance Distortion (THD)  < 0.005% at 1khz, 0dbu output Noise  < -105db unweighted, 22hz-22khz, rms* Frequency Response 30Hz to 20kHz, +0dB/-1dB General Main/Standby battery 9 volt PP3 type, preferably alkaline. Current drain  on phantom - less than 7.5mA on battery - less than 2mA. Phantom Power  +20 volts DC to +48 volts DC Weight 650 gms, excluding batteries. Overall Dimensions  59 mm x 124 mm x 143 mm (2.3" x 4.9" x 5.6“)

Phantom or battery powered in a rugged steel chassis
 
The ARX DI-PLUS 2 represents another major step forward in active direct boxes. Packaged in
a single channel stand-alone format, the DI-PLUS 2 represents a fresh look at active stereo
D.I. concepts.

Precision engineered
Ultra quiet, ultra clean circuitry delivers maximum headroom whatever the signal. Premium grade
components, plus an all-steel chassis gives excellent hum and noise specifications and superb
audio quality in a tough, roadworthy package. Accurate Left and Right channel level matching keeps
the stereo image centred.

Level control
The DI-PLUS 2 features two high impedance unbalanced inputs on the front panel, running to balanced
XLR outputs on the rear. A a global Pad switch drops inputs by 20dB, making it suitable for all applications
from the softest keyboard to the hottest broadcast levels.
 
Battery compartment
The revolutionary simple 'clamshell' action of the DI-PLUS 2 battery compartment makes battery changing
extremely easy, even on the darkest stages.
A 9v alkaline battery snaps into a PCB mounted battery holder for fast, secure location. No fragile battery clip
leads to break, no tools required, no screws to lose. Production crew heaven!
 
Automatic Phantom switching
The DI-PLUS 2 will automatically switch itself to the console's own Phantom Power, if available, and an LED
will indicate this mode. Turn the Phantom Power off and it will instantly revert back to battery mode.

Rugged all-steel case
A lot of direct boxes are fitted into brittle cast alloy cases. Not this one! The tough all-steel inner and outer
chassis of the DI-PLUS 2 provide excellent RF/EMF shielding while making it a sturdy, heavy duty unit that
is hard to dislodge, and hard to leave behind.
 
Rear panel showing Left and Right XLR connectors, ground lift switch, battery check switch and LED, plus
phantom power On LED and captive screw for opening up the unit for battery changing
 
Whether you're a Studio or Live Sound engineer, installation contractor, or broadcast engineer, you want all
the dynamics,clarity and stereo information of the original sound source transferred to the mixing console.
The ARX DI-PLUS 2 provides a rugged, no-compromise solution to all stereo direct injection and signal
balancing requirements.
 
T E C H N I C A L S P E C I F I C A T I O N S:
Max Input Level
+12 dB Phantom powered
+6 dB Battery powered
Input Impedance 1 Meg Ohm
Max Output Level
+17 dB 10K Ohm load Phantom powered
+12 dB 10K Ohm load Battery powered
+11 dB 600 Ohm load Phantom powered
+12 dB 600 Ohm load Battery powered
Output Impedance 680 Ohms Balanced
Output Signal to Noise
-100 dB unweighted
-104 dB A weighted
Dynamic Range
117 dB 10K Ohm load Phantom powered
112 dB 10K Ohm load Battery powered
111 dB 600 Ohm load Phantom powered
107.5 dB 600 Ohm load Battery powered
Distortion 100 Hz .0018%, 1KHz .0028%, 10KHz .0056%
Frequency Response 20Hz to 20KHz, ± 0.2 dB
Gain through Unit: 6dB (Pad switch out)
Pad Switch: Global -20 dB attenuation
Input and Loop Out Connectors
Insulated jacks (!!!Note that Channel A Input connector switches the unit on
when a plug is inserted. Remove plug when storing to avoid battery drain!!!)
Output Connectors
3 pin XLR. Wired Pin 1 Ground, Pin 2 + Hot, Pin 3 - Cold.
Global Audio Ground (Pin 1) lift switch
Construction
All-steel chassis, fibreglass PCB
Battery Access
Twist connector opens chassis, snap-in battery holder inside.
No tools required

Weight0.60 kg0.50 kg1.90 kg0.31 kg0.65 kg0.60 kg
DimensionsN/AN/AN/AN/AN/AN/A
Additional information
Weight 0.60 kg
Weight 0.50 kg
Weight 1.90 kg
Weight 0.31 kg
Weight 0.65 kg
Weight 0.60 kg