Content |
Cable Tester ACT-100
The Alphaton active remote cable tester can be used for testing either normal short cables or long ones, especially mufticores, wkh connectors not being accessible at one time. The tester is especially suded for fixed installations where cables can not be tested with a standard type cable tester or Ohm meter. Either symmetric and unsymmetric cables can be tested. “Cold" solderings and junction resistances are displayed by color or luminosity changes in three color LED Display. The imprinted fault table incorporates alt important fault conditions, indeed not all possible ones due to their reiatively large number. In case the display is in a state which cannot be found on the imprinted table, it can be looked up in the user's manual. In any case, however, the cabie is in aquite unusable state and should be repaired or replaced.The Alphaton cable tester has a SEND and a REMOTE section. The REMOTE sectionconsistsof two recessed mounted XLR type male or female connector and a stereo phone jack at the right hand side of the tester. Additionally, a separate REMOTE plug is delivered togetherwith the active remote cable tester for testing long cables in fixed installations.
| Digital Sound 8928 SPL Meter with Built-In Measurement Mic - calibrated from 300Hz to 8kHz (+/-2dB), 4 control zones in 10dB steps (40-130dB), large LCD display, peak-hold, fast/slow display modes, includes 9V battery.
A superbly designed easy to use sound level meter with features normally only found on more expensive instruments. It has an electret condenser microphone giving virtually instant readings updated every 0.5 seconds on an extra large LCD display.
- 4 measuring ranges, 40 to 70dB, 60 to 90dB, 80 to 110dB or 100 to 130dB
- 0.1dB resolution updated every 0.5 seconds
- Auto ranging or manual range selection
- ʽAʼ & ʽCʼ frequency weighting
- Fast or slow response filters
- 42mm LCD display with quasi-analogue bargraph and function Indicators
- Bargraph in 1dB steps updated every 40ms
- Max hold function to display the highest recorded value
- Min/max memory since power on or last reset
- Low battery indicator
- Auto power off
- Analogue output AC: 0.707 Vrms (at full scale)
- Supplied with battery
|
Digilyzer? DL1
Digital audio analyzer / audio meter with integrated speaker, audio lens and a
comprehensive event logger. Digital audio becomes simple by using the Digilyzer DL1.
The digital audio meter Digilyzer DL1 provides a comprehensive set of analysis
functions for digital, audio and video related audio signals.
It handles virtually all digital audio formats including ADAT and sampling frequencies
up to 96 kHz. The simple and intuitive operation allows the user to monitor, analyze
and troubleshoot any digital signals.
Debugging of digital audio signals becames easy with the assistance of the Digilyzer:
Features like the integrity check, the integrated speaker with audio lens function, the
logging functions, the ?over all? view of all important parameters and many more functions
to allow you to understand whats going on and finding faults easier than ever.
The Digilyzer is a handheld, battery powered device with optional mains power supply and
optional USB interface called MiniLINK.
MiniLINK, the USB interface for the Digilyzer allows documentation and data acquisition of
all DL1 functions in conjunction with the easy to use MiniLINK PC application. MiniLINK
supports online data logging up to several days. Read more about MiniLINK.
Product-details
? AES3, S/PDIF, TOS-Link
? ADAT Interface
? Sampling Frequency 32-96 kHz
? Digital Audio Analysis
? Carrier Status Analysis
? Carrier Signal Measurement
? Dual Domain Monitor Speaker
? Comprehensive Event Logger
|
The tester allows to makea fast test connection for many type of audio and lighting cable, checking up to 7 connections (Neutrik? , Speakon?, XL3, XLR5, DIN RCA, Jack and BNC). Two rows of LEDs will light up to indicate which pin is connected correctly. a red lit LED and beep indicate short-circuited connection
Specifications: Battery: PP3 9V(not included) Accessory: Short Tester pinx2(included) Net Weight: 0.71Kg Dimensions: 178x121x44mm | Overview:
This is an infrared digital forehead thermometer with high precision, which is hand-held and portable for easy use. Non-contact design reduces cross infection effectively, widely used for measuring body temperature.
Features:
High precision infrared sensor, stable and reliable, for safe use, ensures accurate measuring, small error.
Alarm temperature can be set and once exceeded, it will give out a beep sound. Also, it supports the Mute mode.
Humanized design, LCD screen display with high brightness backlight can clearly show the body temperature.
Aim at the forehead (3-5cm), press the measuring button, and the LCD display will show the currently measured temperature.
Automatic store 32 sets of measurement data, you can view the data of the previous measurement.
Short press the Function Setting button to switch between Body and Object temperature modes.
Compact design, lightweight and portable, comfortable grip handle, easy to carry, convenient to use.
Suitable for baby, kids, and adult use and can be widely used in school, office, and at home, etc.
Note: The battery is not included.
Specification:
Model: ZK-YK1028
Measuring Method: Non-Contact
Measuring Distance: 3cm-5cm
Unit of Measurement: Celsius(℃), Fahrenheit(°F)
Measuring Range: 32℃-42.9℃ (89.6°F-109.2°F)
Max. Allowable Error: ±0.3℃ within range 35℃-42℃
Display Resolution: 0.1℃/0.1°F
Operating Environment: 16℃-35℃ (60.8°F-95°F), Humidity≤85%
Transportation Storage Environment: -20℃-50℃ (-4°F-131°F), Humidity ≤90%
Power: DC 3V (2 AAA Batteries Not Included)
Backlight: Highlight Backlight
Automatic Shut-down: 30s
Item Size: 15.0 * 8.5 * 4.3cm / 5.90 * 3.34 * 1.69in
Item Weight: 105g / 3.70oz
Package Size: 17.0 * 10.5 * 4.8cm / 6.69 * 4.13 * 1.89in
Package Weight: 156g / 5.50oz
Package List:
1 * Thermometer
1 * User Manual (English)
|
- Microprocessor-controlled cable tester featuring 3 modes: cable and installed cable test plus test tone mode
- Accepts all standard connectors: XLR, Speakon*, TRS (1/4“, 1/8“), RCA, RJ45, MIDI and USB
- Super-easy operation with intuitive LED display
- Continuity check and intermittent contact detection
- Phantom-power and ground-shield check
- Test-tone generator: 1 kHz or 440 Hz at +4 dBu, -10 dBV or -50 dBV
- Operates with 2 AA size batteries (not included)
- Designed and engineered in Germany
|
Reviews
There are no reviews yet.