ALTO TS212W TRUESONIC 1100W ACTIVE LOUDSPEAKER WIRELESS BLUETOOTH

Alto TS212W 12" 2-Way 1100W Bluetooth-Enabled Powered Loudspeaker

• For Live Stage, Theater, and DJ Setups
• 12" Woofer, 1" Tweeter
• 46 Hz to 22 kHz Frequency Range
• Passively-Cooled Class-D Amplification
• Bluetooth-Enabled for Wireless Streaming
• Clip, Thermal, and Transducer Protection
• Combo XLR Jack Inputs, XLR Mix Output
• Built-In Mixer
• 5 x Integrated Carry Handles
• Supports Stand, Pole, and Wedge Mounting

The Alto TS212W is a 12" 2-Way 1100W Bluetooth-enabled powered loudspeaker designed to provide full-range sound reinforcement and convenient I/O for sound engineers, musicians, performers, and DJs in live stage, theater, karaoke, and club setups. Quiet, passively-cooled Class-D amplification drives the 12" woofer and 1” tweeter to produce 1100W of peak power output with a frequency range of 46 Hz to 22 kHz.

Stream music wirelessly via Bluetooth connectivity. The combo jack inputs allow for XLR or 1/4” connections as well. A mono balanced analog output is available on an XLR 3-pin jack. The built-in mixer includes level controls and a selectable Contour switch to emphasize low and high frequencies. LED indicators allow easy identification of the selected settings and power, signal, and limit status. The clip, thermal, and transducer overdrive protection keep the speaker safe.

The lightweight trapezoidal cabinet features five integrated handles for easy lifting. The TS212W can be mounted on a stand or pole via its M10 suspension joints, or it can be configured as a wedge monitor due to its angled rear panel.

• 550W continuous, 1100W peak power
• 12” LF driver, 2.5” high-temperature voice coil
• 1” neodymium HF driver with precision waveguide
• Bi-amplified design with precision active crossover and EQ
• Integrated 2-channel mixer with dual XLR-1/4” combo mic/line inputs and independent level controls
• Bluetooth function allows you to wirelessly stream backing tracks or background music from any Bluetooth-compatible device
• Bluetooth wirelessly streams a stereo signal to separate speakers
• Custom engineered high-efficiency Class-D amplifiers with passive cooling design
• Without the use of fan, the speaker runs cleaner, quieter, and has longer-term reliability
• Ground-lift switch
• Contour switch for increased EQ control
• Electronic clip, thermal and transducer overdrive protection
• Compact, lightweight, trapezoidal cabinet design for easy transport and installation
• Angled rear panel for wedge monitor applications
• Stand and pole-mountable with integral M10 suspension points
• XLR link output
• Designed and tuned in the USA

With a 12" woofer and a 1" titanium compressor driver, the EKX-12P from Electro-Voice is a powered two-way Loudspeaker providing 1500W of Class D amplification. It\'s suitable in live-music scenarios, lecture setups, and generalized nightclub use. The loudspeaker\'s integrated QuickSmartDSP technology can be modified using the LCD-based menu-navigation screen and the single-knob user interface. Four presets of DSP are provided for various settings—Music, Live, Speech, and Club—though EQ manipulation and five user-programmable presets are all adjustable. Visual monitoring of your limiter, input metering, and master volume allow you to gain-stage properly.

Its on-board amplifier can deliver up to 132 dB of SPL, its frequency response ranges from 50 Hz to 20 kHz at -10 dB, and its intelligent thermal-management system controls fan-speed by means of multiple built-in sensors, thus reinforcing the durable performance of this speaker (whose 15mm wooden enclosure is fronted by an 18 AWG steel grille). Electro-Voice\'s SST waveguide design provides measured and dependable coverage of a given area, and the speaker\'s Cardioid Control Technology allows you to steer output towards the audience while reducing levels up to 35 dB on stage when multiple subwoofers are employed.

For convenience in mounting and transport, this loudspeaker boasts eight M10 threaded mounting points, aluminum pole mounts, and metallic handles; as such, it can be mounted on a tripod stand, on a pole above your subwoofer, or utilized as a floor monitor for artists on stage. You can feed the speaker sweet, sweet audio via RCA inputs or XLR/1/4" combination jacks, and you can link it to other monitors via an XLR link-output.

Key Features:
- Compact Powered bi-amplified
full-range loudspeaker with JBL
DrivePack® technology for portable or
installed use
- Optimized for both portable/rental or
permanent-venue use
- 1750 watts peak output power,
875 watts continuous
- 15-inch Differential Drive® lowfrequency
driver for extended lowfrequency
output
- Robust powder-coated die cast
aluminum handles, designed for
strength and comfort
- Integrated 35 mm stand mount

Specifications:
Frequency Response (+/-3 dB): 60 Hz - 18 kHz80 Hz – 20 kHz
Frequency Range (-10 dB): 45 Hz - 20 kHz50 Hz – 20 kHz
Coverage Pattern: 90° x 50°
Directivity Factor (Q): 12.6
Directivity Index (DI): 11 dB
Maximum Peak Output1: 135 dB SPL 1m
Transducer Section:
Low Frequency Section: JBL 2265FF, 381 mm (15 in) dia., 76 mm (3 in) Dual Coil
neodymium Differential Drive®, Direct Cooled
Bandpass Nominal Impedance: 2 x 2 ohms
High Frequency: JBL 2452H-SL, 100 mm (4 in) titanium damped
diaphragm, 1.5 in. exit.
Bandpass Nominal Impedance: 8 ohms
System:
DPC1 Internal Amplification Output
(at nominal load) 1750 Watts Peak, 875 Watts Continuous
DPC1 Output (Continuous IEC shaped
pink noise into rated load impedance): 750LF/125HF Watts
DPC1 Output Section: LF: Dual Bridged Technology™, Class D
HF: Bridged Class D
Audio Input connector XLR with loop-through
User Controls: 80 Hz Subwoofer High Pass Filter. Enable/Disable
0-16 dB input Attenuator with 32 precision 0.5 dB steps
Signal Processing: DSP based, resident in Input Module.
System Management: DSP based limiters for mechanical and thermal
protection
AC Power Operating Range: 90-132 VAC/216-264 VAC, 50/60 Hz
AC Line Voltage: 50/60 Hz; User Selectable; 120V/240V (-15%, +10%)
AC Input Connector: Neutrik PowerCon (NAC 3MPA)
AC Loop-thru: Neutrik PowerCon (NAC 3MPB)
AC Current Requirement: 6A per system at 120V, 3A per system at 240V
Enclosure:
Box Construction: 5/8 in. multi-ply exterior grade Baltic birch. Internally
braced. Black DuraFlex™ finish.
Suspension System: 13 M10 Fittings, 35 mm pole mount socket
Grille: 14 Gauge Black powder-coated perforated steel with
foam backing.
Dimensions (H x W x D): 613 x 434 x 359 mm
24.1 x 17.1 x 14.1 in
Net Weight: 24.7 kg (55 lb)

Features:

DH-1K 1.5-inch Titanium Diaphragm Compression Driver
EVS-12K 12-inch Woofer
121 dB max. SPL
500 W Class-D Amplifier
Integrated DSP with FIR filter


Cabinet
Powered two-way full-range speaker, 12" woofer, 1.5" compression driver, vented design
Maximum Amplifier Output Capability, IHF-A
500 W
Amplifier Power RMS
420 W
Max. SPL 1m / calc.
121 dB
Frequency Range (-10 dB)
55 Hz to 17 kHz
Nominal Coverage Angle
90° x 50° (Horizontal x Vertical)
Audio Input (LINE 1 or MIC/LINE 2)
XLR and 1/4" TRS combination
Audio Input (AUX)
Stereo RCA, unbalanced
Audio Output (LINK OUTPUT)
XLR, balanced
Digital Signal Processing
28/56-Bit, 48 kHz
Crossover Frequency
1.7 kHz
Product Dimensions (W x H x D)
607 x 362 x 340 mm
Net Weight
16.8 kg
Optional Accessories
---
SH-112A, Dust Cover
F01U270395
VPM 1500, variable speaker pole
F01U141047
BS 35, speaker stand
F01U141046

Key Features:
- Compact Powered bi-amplified
full-range loudspeaker with JBL
DrivePack® technology for portable or
installed use
- Optimized for both portable/rental or
permanent-venue use
- 1750 watts peak output power,
875 watts continuous
- 12-inch Differential Drive® lowfrequency
driver for extended lowfrequency
output
- Robust powder-coated die cast
aluminum handles, designed for
strength and comfort
- Integrated 35 mm stand mount

Specifications:
Frequency Response (+/-3 dB): 65 Hz - 18 kHz80 Hz – 20 kHz
Frequency Range (-10 dB): 55 Hz - 20 kHz50 Hz – 20 kHz
Coverage Pattern: 90° x 50°
Directivity Factor (Q): 12.6
Directivity Index (DI): 11 dB
Maximum Peak Output1: 134 dB SPL 1m
Transducer Section:
Low Frequency Section: JBL 2262FF, 304 mm (12 in) dia., 76 mm (3 in) Dual Coil
neodymium Differential Drive®, Direct Cooled
Bandpass Nominal Impedance: 2 x 2 ohms
High Frequency: JBL 2452H-SL, 100 mm (4 in) titanium damped
diaphragm, 1.5 in. exit.
Bandpass Nominal Impedance: 8 ohms
System:
DPC1 Internal Amplification Output
(at nominal load) 1750 Watts Peak, 875 Watts Continuous
DPC1 Output (Continuous IEC shaped
pink noise into rated load impedance): 750LF/125HF Watts
DPC1 Output Section: LF: Dual Bridged Technology™, Class D
HF: Bridged Class D
Audio Input connector XLR with loop-through
User Controls: 80 Hz Subwoofer High Pass Filter. Enable/Disable
0-16 dB input Attenuator with 32 precision 0.5 dB steps
Signal Processing: DSP based, resident in Input Module.
System Management: DSP based limiters for mechanical and thermal
protection
AC Power Operating Range: 90-132 VAC/216-264 VAC, 50/60 Hz
AC Line Voltage: 50/60 Hz; User Selectable; 120V/240V (-15%, +10%)
AC Input Connector: Neutrik PowerCon (NAC 3MPA)
AC Loop-thru: Neutrik PowerCon (NAC 3MPB)
AC Current Requirement: 6A per system at 120V, 3A per system at 240V
Enclosure:
Box Construction: 5/8 in. multi-ply exterior grade Baltic birch. Internally
braced. Black DuraFlex™ finish.
Suspension System: 9 M10 Fittings + 2 M6 Fittings, 35 mm pole mount
socket
Grille: 14 Gauge Black powder-coated perforated steel with
foam backing.
Dimensions (H x W x D): 533 x 358 x 334 mm
21.0 x 14.1 x 13.1 in
Net Weight: 21.3 kg (47 lb)