Content | VLP Series Power Amplifier
- 1100W RMS Per Channel @ 4 Ohms, 1kHz, 0.1% THD
- 700W RMS Per Channel @ 8 Ohms, 1kHz, 0.1% THD
- 2200W RMS @ 8 Ohms, 1K Hz, 1% THD (Bridge Mode, Mono)
- Total Harmonic Distortion: Less Than 0.5% (20Hz - 20kHz @ 8 Ohms)
- Frequency Response: (+/-05db, @rated output Power, 8 Ohms): 20Hz - 20K Hz
- Slew Rate: 20V Per usec
- Damping Factor @ 8 Ohm: 450
- Impedance: 20 Ohms balanced / 10 Ohms unbalanced
- Cooling System: 2 high speed cooling fans
- Special Features: High/Low Pass Filter / Input Sensitivity Selector / Ground Lift / Limiter
- Dimensions (LxWxH): 17.75" x 19" x 3.5" / 453 x 482 x 88mm (2 rm spaces)
- Weight: 50 lbs. / 23 Kgs. |
This professional stereo power amplifier, working in class-H mode, provides 2x1600W, at an efficiency of around 85%.
A massive transformer based power supply and hand selected components makes this power rating possible with exceptional audio quality and absolute reliability, even in the 2 Ohm mode.
The output stage is fully protected against over-temperature, short circuit, RFI and equipped with soft start circuit and temperature-controlled fan cooling.
The integral soft clip limiter protects against damage to the connected loudspeakers.
The activity of a protective circuit, signal and limiter is shown for each channel by LEDʼs.
AMPLIFIER SPECIFICATIONS |
---|
Power output stereo 2Ω: | 2 x 1600 Watt rms | | Power output stereo 4Ω: | 2 x 1100 Watt rms | | Power output stereo 8Ω: | 2 x 700 Watt rms | | Power output bridged 4Ω: | 3200 Watt rms | | Power output bridged 8Ω: | 2200 Watt rms | | Frequency Response: | 20 Hz ÷ 20 kHz | | Signal/noise rate: | > 102 dB | | Crosstalk: | > 65 dB | | Distortion (THD+N): | | | Intermodulation: | | | Damping factor: | 400:1 (8 W) | | Slew rate: | 50 V/μS | |
INPUT SECTION |
---|
Input connector: | 2 x XLR balanced, 6,3mm jack unbalanced | | Input sensitivity: | 0 / 0.775 dBm/V RMS | | Input impedance: | 20.000 kΩ | | Controls: | Volume control for each channel | |
OUTPUT SECTION |
---|
Output connector: | 2 x Neutrik Speakon 4 ways | |
SYSTEM PARAMETERS |
---|
Cooling: | Two-speed fan | | Protections: | Thermal, temperature, direct current, short circuit, RFI | |
POWER REQUIREMENT |
---|
Operating voltage: | 220÷240 / 110÷120 ~ 50 / 60 V ~ Hz | | Max.current: | 16 A | | Power Consumption: | 6500 W | |
PHYSICAL SPECIFICATIONS |
---|
Height: | 132 / 5.19 mm/inch | | Width: | 483 / 19.01 mm/inch | | Depth: | 455 / 17.91 mm/inch | | Net Weight: | 29.5 / 65.03 Kg/Lbs | |
SHIPPING INFORMATION |
---|
Package height: | 200 / 7.87 mm/inch | | Package width: | 575 / 22.63 mm/inch | | Package depth: | 555 / 21.85 mm/inch | | Shipping Weight: | 32.5 / 71.64 Kg/Lbs |
|
The versatile PX series power amplifiers lineup combines intelligent processing with high output power to meet the requirements of a vast range of sound reinforcement environments. 2x800W@8Ω / 2x1050W@4Ω
The versatile PX series power amplifiers lineup combines intelligent processing with high output power to meet the requirements of a vast range of sound reinforcement environments.
- 2x800W@8Ω
- 2x1050W@4Ω
- Newly developed Class-D amplifier engine with a custom LSI
- Flexible onboard PEQ, crossover, filters, delay, and limiter functions
- Yamaha Speaker presets
- Utlities for safe and secure operation
Type: | Power Amplifier | Power: | 1050W x 2 / 4Ω, 2 x 800W x 8Ω | Frequency Response: | - | Inputs: | XLR-3-31 x2, 1/4 "PHONE(TRS) x2 | Οutput: | Neutrik speakON NL4 x2, Binding post x2 pairs, 1/4" PHONE(TS) x2 | THD: | 0.1% (1kHz, 10W), 0.3% (1kHz, Half power) | Special Items: | - | Dimensions (W x H x D): | 48 x 8.8 x 38.8 cm | Rack Mount: | Yes | Weight: | 7,2 kg | Τype: | Low Impedance | Power 4Ω: | 1000W-1500W | Rack Mount: | 2U |
|
Crown DSi 4000 2x1200W-4Ω Power Amplifier
The Crown? DSi 4000 power amplifi er shall be a solid-state two-channel model
with a switch-mode universal power supply. A rear-panel HD-15 connector shall
provide input/output connectivity between the DSi amplifi er and the DSi-8M
System Monitor.
The outputs shall be usable as stereo or bridged-mono modes of operation.
The bridged-mono mode shall bridge the outputs to provide increased output
voltage.
Front panel controls and indicators shall include the following:
Level: Detented rotary level control, one per channel.
Power Switch: On/off switch applies AC power to the amplifi er.
Sel/Prev/Next Buttons: Three buttons near the LCD screen shall be used to
access menu items and front panel lockout.
LCD Screen: Backlit liquid crystal display shows speaker presets and signal
processing.
Signal Indicator: Green LED, one per channel, illuminates when a very low-level
signal is present at input.
?10 Indicator: Green LED fl ashes when output signal exceeds ?10 dB below
clip.
?20 Indicator: Green LED fl ashes when output signal level exceeds ?20 dB
below clip.
Ready Indicator: Green LED, one per channel, illuminates when the amplifi er is
ready to produce audio.
Clip Indicator: Red LED, one per channel, turns on at the threshold of audible
distortion.
Temp Indicator: Red LED, one per channel, illuminates under excessive temperature
conditions.
Power Indicator: Blue LED illuminates when the amplifi er has been turned on
and has power.
Rear panel controls and connectors shall include the following:
AC Line Connector: NEMA 5-15P (15A).
Input Connector: Two 3-pin removable Phoenix-type connectors each accept a
balanced line-level input signal.
Output Connectors: 4-position barrier strip with connectors for dual louspeakers
or bridge-mono loudspeaker.
HiQnet USB Connector: Type B, connects to a HiQnet network.
HD-15 Connector: For cinema I/O compatibility with DSi-8M System Monitor.
The amplifi er shall have the following specifi cations:
Output Power: 2 ohm Stereo (per channel): 1,600W with 1% THD, 4 ohm
Stereo (per channel): 1,200W with 0.5% THD, 8 ohm Stereo (per channel):
650W with 0.5% THD, 4 ohm Bridge-Mono: 3,200W with 1% THD, 8 ohm
Bridge-Mono: 2,400W with 0.5% THD.
Voltage Gain at 1kHz, 8 ohm rated output: 26 dB.
Frequency Response: +0/?1 dB from 20 Hz to 20 kHz at 1 watt into 4 ohms.
Load Impedance: Safe with all types of loads. Rated for 2 to 8 ohms in Stereo
mode, 4 to 16 ohms in Bridge-Mono mode.
Sensitivity at 8 ohm rated output: 3.61V.
Sensitivity at 4 ohm rated output: 3.47V.
Sensitivity at 2 ohm rated output: 2.84V.
Signal to Noise Ratio (below rated 8-ohm power at 1 kHz): 105 dB
(A weighted).
Damping Factor: Better than 500 from 20 Hz to 500 Hz.
Crosstalk: > 70 dB below rated power, 20 Hz to 1 kHz.
Input Stage: Input is electronically balanced and employs precision 1% resistors.
Input Impedance (nominal): 20 k ohms, balanced;10 k ohms, unbalanced.
Maximum Input Signal: +22 dBu typical.
AC Line Voltage and Frequency Confi gurations Available: 100V, 120V, 220-240V,
50/60 Hz.
AC Line Current: 8.0A.
At Idle: Draws no more than 90 watts.
Operating Temperature: 0° C to 40° C at 95% relative humidity (non-condensing).
The DSP section shall have the following specifi cations:
Input EQ: 6 parametric fi lters per channel with adjustable Q, ±15 dB boost/cut.
Also adjustable high and low shelving fi lters. This 8-fi lter EQ section can be
bypassed.
Crossover Filters: Highpass and lowpass per channel. Butterworth 6/12/18/24
dB per octave, Linkwitz-Riley 24/48 dB per octave. Also includes ±15 dB bandpass
gain and polarity control.
Output EQ: 8 parametric fi lters per channel with adjustable Q, ±15 dB boost/cut.
This 8-fi lter EQ section can NOT be bypassed. Filters are enabled individually.
Output Limiter: Prevents clipping and protects loudspeakers. Choice of ?3, ?6,
or ?12 dB threshold per channel.
Delay: Up to 50 msec total delay per channel.
Presets: 20 presets. One is ?DSP OFF.? Fifteen are factory-set for JBL Cinema
systems. Four are user-defi nable.
Protection shall include the following:
DSi-Series amplifi ers shall be protected against shorted, open or mismatched
loads; overloaded power supplies; excessive temperature; chain destruction
phenomena; excessive output current, and input overload damage. They also
protect loudspeakers from input/output DC, large or dangerous DC offsets and
turn-on/turn-off transients
The chassis shall be steel. Cooling shall be by a proportional speed fan with
front-to-rear airflow.
Dimensions shall be EIA Standard 19-in. rack mount width (EIA RS-310-B), 3.5
in. (8.9 cm) high and 12.25 in. (31.11 cm) deep behind mounting surface.
Net weight shall be 19 lb (8.6 kg). Shipping weight shall be 22 lb (10.0 kg)
The amplifier shall be designated the Crown DSi 4000.
|
The power amp H2500 is part of Dynacordʼs new PowerH SERIES, which marks a milestone in the design and the production of high-performance power amplifiers. The innovative 3-stage Grounded Bridge Class H Topology with "floating” switching power supply unit offers very high and stable output with extreme high efficiency on an extremely high performance level at minimum weight. PowerH amps are ideal for driving professional touring, high-end Concert-Sound and Pro-Sound applications. Next to classical protections, this new design employs the multi-stage ATP system (Advanced Thermal Protection) for the first time, which in most cases prevents the power amplifier from switching off when the temperature exceeds a critical level. The newly designed MCS system (Mains Current Supervision) prevents power amplifier breakdown caused by the activation of the automatic circuit breaker. For this, among other things, the MCS system uses the highly precise measurement of the RMS value ofthe actual mains current consumption. Information about the status of the power amplifier and its internal protections is provided on a LC-display. By utilizing the optionally available remote control module that is compatible with IRIS-Net™, this power amplifier additionally offers comprehensive remote monitoring and remote control functions plus a universal 2-channel digital audio controller (DSP) including highly precise FIR-filtering and digital speaker protection algorithms. Datasheets / ManualsManual (5.50MB)
Load Impedance 2 O, 4 O, 8 O Maximum Midband, Output Power, 1 kHz, THD=1% 2 O - 1900 W, 4 O - 1450 W, 8 O - 850 W Rated Output Power, 20 Hz ... 20 kHz, THD 400 Slew Rate 30 V/µs Signal to Noise Ratio Amplifier, A-weighted, 32 dB constant gain 109 dB Output Noise , A-weighted
|
The S Series of RAM Audio amplifiers distils all these features to fulfill all your needs, whether youʼre starting a P.A. amplifier project from scratch, or you need to upgrade your present sound reinforcement equipment.
In the S Series amps, you'll find five 2-channel models and five 4-channel models, all offering plentiful power levels at low distortion in the range of 1.5 to 6 kilowatts, yet weighing in around 8 kilos and 30 cm deep.
• Ultra-compact and lightweight 2-U high
• Laser cut aluminum front panels with integrated carrying handles
• Neutrik® XLR input connectors, input and signal link in 2 channel models
• Input Link switch: allow daisy-chaining of the input signal
• Neutrik® Speakon® output connectors
• Detented sealed potentiometers for easy recall of volume settings
• ICL™, PMS™, Hi-temp, Signal indicators per channel
• Power on and Stand-by leds
• Highly versatile with multiple configuration and additional module options
• Full PC control via EtheRAM (with EtheRAM Control module)
• Switchable ICL™ clip-limiters per channel
• Switchable (30-50 Hz) sub-sonic highpass filter per channel
• Three-position gain selector (26, 32 or 38 dB)
• Dual or bridge mode selector
• Twin temperature controlled, back to front cooling fans
• Oversized power components (high SOA reserve specification)
Standard Signal Inputs Module: The S Series amps are equipped as standard with twin Neutrik® XLR, doubled by two other XLR connectors for linking purposes. In the 4 Channel models an XLR input per channel is provided with the signal linking facility.
Analog Processor Module: permits a very easy, user-friendly signal processing to enable the amp to set up a bi-amp system without any other outboard device. These are the Processor's main characteristics:
• 2-way stereo crossover (dual mono or single bridged sub output)
• 24dB/oct Linkwitz-Riley configurable crossover (90, 100 o 120Hz)
• Adjustable attenuation in the High-pass outputs (-3, -6 or -9dB)
• Adjustable Limiter, relative to Max. Output (-3, -6 or -9dB)
DSP44_S Module: Digital Signal Processor fully programmable through an USB port. These are the Processor's main characteristics:
• 4 Inputs/4 Outputs or 2 In/2 Out free route configurable.
• 24 bits/192 kHz 256x Oversampling Converters.
• Output Delay: 0 to 7.1 meters (20.69ms) per channel.
• XOver: Up to 48dB/oct Butterworth, Linkwitz-Riley and Bessel.
• EQ: 9 filters per channel (Parametric, Shelving, LP,HP,BP,SB).
• Gain, Mute and Phase inversion per channel.
• RMS Power and Peak Voltage output limiter per channel.
• Real Time operation from USB or front panel configuration.
Standard Signal Inputs Module
EtheRAM Control Module
Ethernet Audio Transport (Coming soon)
Analog Processor Module
DSP44_S Module
EtheRAM Control Module
AES/EBU Digital Input (Coming soon)
|
OUTPUT POWER |
S-1500 |
S-2000 |
S-3000 |
S-4000 |
S-6000 |
S-3004 |
S-4004 |
S-4044 |
S-6004 |
S-6044 |
1kHz, 1.0% THD |
|
|
|
|
|
|
|
|
|
|
2 ohms |
2x880W |
2x1190W |
2x1570W |
2x1950W |
2x2950W |
4x700W |
4x980W |
- |
4x1440W |
- |
4 ohms |
2x575W |
2x790W |
2x1100W |
2x1380W |
2x2025W |
4x500W |
4x670W |
4x975W |
4x1000W |
4x1480W |
8 ohms |
2x325W |
2x460W |
2x630W |
2x810W |
2x1250W |
4x300W |
4x430W |
4x690W |
4x620W |
4x1015W |
Bridge @ 4ohms |
1760W |
2380W |
3140W |
3900W |
5900W |
2x1400W |
2x1960W |
- |
2x2880W |
- |
Bridge @ 8ohms |
1150W |
1580W |
2200W |
2760W |
4050W |
2x1000W |
2x1340W |
2x1950W |
2x2000W |
2x2960W |
P. N. 12dB C.F. |
|
|
|
|
|
|
|
|
|
|
2 ohms |
2x975W |
2x1360W |
2x2060W |
2x2460W |
2x4225W |
4x890W |
4x1170W |
- |
4x2080W |
- |
4 ohms |
2x610W |
2x880W |
2x1240W |
2x1600W |
2x2600W |
4x580W |
4x820W |
4x1230W |
4x1280W |
4x2110W |
Frequency Response (power bandwidth ±0.25dB): 20Hz-20kHz
Phase Response (@1W 20Hz-20kHz): ±15deg
Total Harmonic Distortion (20Hz-20kHz): Intermodulation Distortion (SMPTE): Crosstalk (20Hz-20kHz): >75dB
Voltage Gain (selectable): 26/32/38 dB
Sensitivity: 1500:2.6/1.3/0.6V 2000:3.0/1.5/0.8V 3000:3.6/1.8/0.9V 4000:4.0/2.0/1.0V 6000:5.0/2.5/1.3V
3004:2.6/1.3/0.6V 4004:3.0/1.5/0.8V 4044:3.7/1.9/0.9V 6004:3.5/1.8/0.9V 6044:5.0/2.5/1.3V
Signal to noise ratio: 1500:112dB 2000:113dB 3000:115dB 4000:116dB 6000:118dB
3004:112dB 4004:113dB 4044:116dB 6004:116dB 6044:118dB
Required AC Mains (@4ohms 1/8 r.p.): 1500:4A 2000:4.8A 3000:6.2A 4000:7.5A 6000:10.5A
3004:6A 4004:7.5A 4044:11A 6004:10.5A 6044:15A
Dimensions (WxHxD): 483x88.9x310 mm - 19x3.5x12.2 inches
Weight (Net): 1500/2000: 8Kg - 17.6Lbs 3000/4000/3004/4004/4044: 8.5Kg-18.7Lbs 6000/6004/6044: 8.6Kg-18.9Lbs
Protections: Soft-start, Turn-on Turn-off transients, Muting at turn-on, Over-heating, DC, RF, Short-circuit, Open or mismatched loads, Overloaded power supply,ICL™, PMS™, SSP™ |
Reviews
There are no reviews yet.