| Content |
VLP Series Power Amplifier
Output Power:
- 150W RMS Per Channel @ 4 Ohms, 1kHz, 0.1% THD
- 100W RMS Per Channel @ 8 Ohms, 1kHz, 0.1% THD
(Bridge Mode, Mono)
- 300W RMS @ 8 Ohms, 1K Hz, 1% THD
Total Harmonic Distortion: Less Than 0.1% (20Hz - 20kHz @ 8 Ohms)
Frequency Response: (+/-01db, @rated output Power, 8 Ohms): 20Hz - 20K Hz
Slew Rate: 15V Per usec
Damping Factor @ 8 Ohm: 260
Impedance: 20 Ohms balanced / 10 Ohms unbalanced
Cooling System: 2 indivdual fans
Special Features: High/Low Pass Filter / Input Sensitivity Selector / Ground Lift
Dimensions (LxWxH): 13.25" x 19" x 1.75" / 336 x 482 x 44mm (1-rack mount space)
Weight: 24 lbs. / 11Kgs.
Special Features: High/Low Pass Filter; Input Sensitivity Selector; Ground Lift
|
XB Series - Intelligent Power
Power Without Compromises.
The XB is designed for paging, music and alarm signals. Versatile, dynamic
and extremely rugged according to IEC286-3. For the highest requirements
in safety and quality.
Sequential power on, alive contacts and incorporated ground fault detection-
the XB is the solution under all conditions. Without the need for additional
equipment. For uninterrupted and troublefree operation.
High Tech SMT Design
Protection Circuits: DC, LF, HF, Thermal, Short Circuit, Current Limiter,
3 ms Muting Delay
PHOENIX / Speakon
LED Indicators for POWER, SIGNAL, CLIP, PROTECT
Temperature controlled, variable speed low noise fans
Volume Controls at the back
Stereo / Bridged / Parallel Mode
Softstart
Sequential Remote Power On
Alive Contact
Ground Lift
3 Years Warranty
TECHNICAL DATA:
XB 400: 2x 200 W @ 4 Ohm
Class: AB
Frequency Response: 20 Hz - 20 kHz (0 / -0.3 dB)
THD: < 0.025%
Signal-to-Noise Ratio: < 103 dB
Channel Seperation: > 85 dB
Input Sensitivity: +6 dBu
Input Clipping: 22 dBu
Input Impedance: 20 kOhm
Damping Factor: 500 @ 4 Ohm
Cooling: 2x fan (temp. reg. variable speed)
Weight:12 kg /(26 lbs)
Dimensions: 2 RU / 483 x 88 x 382 mm (19" x 3.5" x 15“) |
The DA-250F is a 4-Channel Digital Power Amplifier featuring lightweight, compact, high power output, and high efficiency. It delivers 250 W × 4 channels (4 Ω output) using a switching power supply. Each channel is equipped with an independent power section. It can be mounted in an EIA Standard equipment rack (1 unit size).
*0 dB = 0.775 V | Power Source | 120 V AC, 50/60 Hz | | Amplification System | Class D | | Power Consumption | 200 W (based on UL/CSA standards)
1300 W (rated output 4 Ω × 4)
850 W (rated output 8 Ω × 4) | | Input | 4 circuits, +4 dB* (1.23 V) (input level control in maximum position),
10 kΩ, electronically-balanced, removable terminal block (3 pins)
CH 1 mode ON/OFF switch (ON: CH 1 to All ch, OFF: Each ch) | | Rated Output | 4 channels: 250 W × 4 (4 Ω), 170 W × 4 (8 Ω)
2 channels (BRIDGE): 500 W × 2 (8 Ω)
M4 screw terminal, distance between barriers: 8.8 mm | | Frequency Response | 20 - 20,000 Hz (±1 dB) | | Total Harmonic Distortion | 0.1% (1 kHz)
0.3% (20 - 20,000 Hz) | | Protection Circuit | Protection against excessive current flow due to overload,
short circuit, unusual DC voltage output,
temperature rise at power amp. heat sink (110℃ or more),
temperature rise inside the unit (80℃ or more) | | S/N Ratio | 100 dB (A-weighted) | | Crosstalk | 70 dB (A-weighted) | | LED Indicator | Power (blue) × 1, Input (green) × 4, Output (yellow) × 4,
Peak (red) × 4, Protect (red) × 4 | | Cooling | Forced air cooling | | Operating Temperature | -10℃ to +40℃ | | Operating Humidity | 90% RH or less (no condensation) | | Finish | Panel: Aluminum, black, alumite Case: Plated steel sheet | | Dimensions | 482 (W) × 44 (H) × 401.8 (D) mm | | Weight | 6.6 kg | | Accessory | Power cord (2 m) …1, Removable terminal plug (3 pins) …4,
Tamper-proof cap …4 |
|
Solid DYNACORD amplifier technology at highly competitive prices.
These amplifiers offer high, stable power output and a high efficiency factor on the high performance level and are therefore the ideal choice for driving a multitude of mobile and club systems. SL series power amplifiers are equipped with a comprehensive protection package and dynamic limiters.
The integrated, switchable Low-Pass Notch filter (a typical DYNACORD special feature) corrects the frequency response and optimizes the transient behaviour of loudspeakers.
Maximum Midband Output Power, THD = 1%, 1 kHz, Dual Channel 2 Ω - 900 W, 4 Ω - 600 W, 8 Ω - 380 W Maximum Single Channel Output Power, Dynamic-Headroom, IHF-A 2 Ω - 1700 W, 4 Ω - 950 W, 8 Ω - 480 W Maximum Bridged Output Power, THD = 1%, 1 kHz 4 Ω - 1800 W, 8 Ω - 1200 W Input Sensitivity, rated power @ 8 Ω, 1 kHz +3.1 dBu (1.11 Vrms) Maximum Input Level +21 dBu (8.69 Vrms) Voltage Gain, ref. 1 kHz 32.0 dB Frequency Response, ref. 1 kHz 10 Hz...40 kHz (±1 dB) Output Stage Topology Class AB Dimensions (W x H x D), mm 483 x 88.1 x 421.5 Weight 14.8 kg (32.6 lbs)
|
- 2Χ350W 8Ω 2x500W 4Ω 2x650W STEREO MODE
- BRIDGE 2000W 4 Ω
- 16Kg
- 2 x 1,000 Watts into 2 Ohms; 2 x 750 Watts into 4 Ohms; 2,000 Watts into 4 Ohms (bridge mode)
- Precise Power, Signal and Clip LEDs to monitor performance
- XLR and 1/4" TRS input connectors for compatibility with any source
- Professional speaker connectors and "touch-proof” binding posts support most speaker wiring systems
- Selectable low-frequency filters (30 Hz or 50 Hz) remove distracting infra-sound frequencies
- Independent limiters per channel offer reliable protection against overload and distortion
- High-current toroidal transformer for ultra-high transient response and absolute reliability
- Ultra-reliable Toshiba/Fairchild power transistors
- Independent DC and thermal overload protection on each channel automatically protects amplifier and speakers without shutting down the show
- “Back-to-front” ventilation system including air filter for reliable operation
- “Built-like-a-tank,” impact-resistant, all-steel 2U rackmount chassis
- High-quality components and exceptionally rugged construction ensure long life
- Conceived and designed by BEHRINGER Germany
|
These amplifiers offer high, stable power output and a high efficiency factor on the high performance level and are therefore the ideal choice for driving a multitude of mobile and club systems. SL series power amplifiers are equipped with a comprehensive protection package and dynamic limiters.
The integrated, switchable Low-Pass Notch filter (a typical DYNACORD special feature) corrects the frequency response and optimizes the transient behaviour of loudspeakers.
Maximum Midband Output Power, THD = 1%, 1 kHz, Dual Channel 2 Ω - 650 W, 4 Ω - 450 W, 8 Ω - 270 W Maximum Single Channel Output Power, Dynamic-Headroom, IHF-A 2 Ω - 1150 W, 4 Ω - 660 W, 8 Ω - 350 W Maximum Bridged Output Power, THD = 1%, 1 kHz 4 Ω - 1300 W, 8 Ω - 900 W Input Sensitivity, rated power @ 8 Ω, 1 kHz + 2,2 dBu (1,0 Vrms) Maximum Input Level +21 dBu (8.69 Vrms) Voltage Gain, ref. 1 kHz 32.0 dB Frequency Response, ref. 1 kHz 10 Hz...40 kHz (±1 dB) Output Stage Topology Class AB Dimensions (W x H x D), mm 483 x 88.1 x 421.5 Weight 12.6 kg (27.8 lbs)
|
Reviews
There are no reviews yet.