The high efficiency of the ED series enables maximum efficiency with low heat generation.
A new and unique Class-H circuity technology using state of the art SMD Surface Mount Technology with a reduced number of components offering performance levels exceeding audiophile levels like a slew rate of 50V/µs and high-end extended dynamic sound. The amplifier provides 2x300W into 4 Ohm is equipped complete with temperature-controlled fan cooling, all common protective circuits such as over-temperature, short circuit, RFI and soft start.
The integral soft clip limiter protects against damage to the connected loudspeakers, the activity of a protective circuit, signal and limiter are shown for each channel by LEDʼs.
AMPLIFIER SPECIFICATIONS
Power output stereo 4Ω:
2 x 300 Watt rms
Power output stereo 8Ω:
2 x 180 Watt rms
Power output bridged 8Ω:
600 Watt rms
Frequency Response:
20 Hz ÷ 20 kHz
Signal/noise rate:
> 105 dB
Crosstalk:
> 70 dB
Distortion (THD+N):
Intermodulation:
Damping factor:
200:1 (8 Ω)
Slew rate:
50 V/μS
INPUT SECTION
Input connector:
2 x XLR balanced, 6,3mm jack unbalanced
Input sensitivity:
0 / 0.775 dBm/V RMS
Input impedance:
10.000 kΩ
Controls:
Volume control for each channel
OUTPUT SECTION
Output connector:
2 x Neutrik Speakon 4 ways
SYSTEM PARAMETERS
Cooling:
Two-speed fan
Protections:
Temperature, DC, RFI short circuit, Soft-Start thermal on transformer
Amplifier class:
H
POWER REQUIREMENT
Operating voltage:
220÷240 / 110÷120 ~ 50 / 60 V ~ Hz
Max.current:
6 A
Power Consumption:
1300 W
PHYSICAL SPECIFICATIONS
Height:
88 / 3.46 mm/inch
Width:
483 / 19.01 mm/inch
Depth:
350 / 13.77 mm/inch
Net Weight:
11.45 / 25.24 Kg/Lbs
SHIPPING INFORMATION
Package height:
120 / 4.72 mm/inch
Package width:
540 / 21.25 mm/inch
Package depth:
470 / 18.05 mm/inch
Shipping Weight:
13.81 / 30.44 Kg/Lbs
Solid DYNACORD technology for fixed installations at very competitive prices. DSA power amplifiers offer a very high, stable output with high efficiency at a high performance level and are therefore the ideal choice for typical fixed installation applications. The connectivity consequently provides Phoenix type in/outs, the input level controls are located on the rear panel, also a switchable high-pass filter (50 Hz, 18 dB/oct) and a Ground Lift switch. The POWER REMOTE connector makes the task of remote controlling the power amplifier as well as switching it on and off simple. For further remote-supervision and –control possibilities and integration into IRIS-Net networks, an optional remote control module (RCM-810) is available.
InterM V-1000 Power amplifier 2Χ340W/4ohm, 2Χ180W/8ohm, 2Χ600W/2ohm bridge 1200W/4ohm 10-83kHz
This website uses cookies to improve your experience. We'll assume you're ok with this, but you can opt-out if you wish. Cookie settingsACCEPT
Privacy & Cookies Policy
Πολιτική χρήσης
Αυτός ο ιστότοπος χρησιμοποιεί cookies για να βελτιώσει την εμπειρία σας ενώ περιηγείστε στον ιστότοπο. Από αυτά τα cookies, κάποια cookie κατηγοριοποιούνται ως απαραίτητα να αποθηκεύονται στο πρόγραμμα περιήγησης σας, καθώς είναι απαραίτητα για τη λειτουργία βασικών λειτουργιών του ιστότοπου. Χρησιμοποιούμε επίσης cookies τρίτων που μας βοηθούν να αναλύσουμε και να κατανοήσουμε πώς χρησιμοποιείτε αυτόν τον ιστότοπο. Αυτά τα cookies θα αποθηκευτούν στο πρόγραμμα περιήγησης σας μόνο με τη συγκατάθεσή σας. Έχετε επίσης την επιλογή να εξαιρεθείτε από αυτά τα cookies. Ωστόσο, η εξαίρεση από ορισμένα από αυτά τα cookie μπορεί να επηρεάσει την εμπειρία περιήγησης σας.
Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.
Any cookies that may not be particularly necessary for the website to function and is used specifically to collect user personal data via analytics, ads, other embedded contents are termed as non-necessary cookies. It is mandatory to procure user consent prior to running these cookies on your website.
.<br> Input Connector: Two 3-pin removable Phoenix-type connectors each accept a<br> balanced line-level input signal.<br> Output Connectors: 4-position barrier strip with connectors for dual louspeakers<br> or bridge-mono loudspeaker.<br> HiQnet USB Connector: Type B, connects to a HiQnet network.<br> HD-15 Connector: For cinema I/O compatibility with DSi-8M System Monitor.<br> The amplifi er shall have the following specifi cations:<br> Output Power: 2 ohm Stereo (per channel): 700W with 1% THD, 4 ohm Stereo<br> (per channel): 500W with 0.5% THD, 8 ohm Stereo (per channel) 275W with<br> 0.5% THD, 4 ohm Bridge-Mono: 1,400W with 1% THD, 8 ohm Bridge-Mono:<br> 1,000W with 0.5% THD.<br> Voltage Gain at 1kHz, 8 ohm rated output: 26 dB.<br> Frequency Response: +0/?1 dB from 20 Hz to 20 kHz at 1 watt into 4 ohms.<br> Load Impedance: Safe with all types of loads. Rated for 2 to 8 ohms in Stereo<br> mode, 4 to 16 ohms in Bridge-Mono mode.<br> Sensitivity at 8 ohm rated output: 2.35V.<br> Sensitivity at 4 ohm rated output: 2.24V.<br> Sensitivity at 2 ohm rated output: 1.88V.<br> Signal to Noise Ratio (below rated 8-ohm power at 1 kHz): 105 dB<br> (A weighted).<br> Damping Factor: Better than 500 from 20 Hz to 500 Hz.<br> Crosstalk: > 70 dB below rated power, 20 Hz to 1 kHz.<br> Input Stage: Input is electronically balanced and employs precision 1% resistors.<br> Input Impedance (nominal): 20 k ohms, balanced;10 k ohms, unbalanced.<br> Maximum Input Signal: +22 dBu typical.<br> AC Line Voltage and Frequency Confi gurations Available: 100V, 120V, 220-240V,<br> 50/60 Hz.<br> AC Line Current: 6.5A.<br> At Idle: Draws no more than 90 watts.<br> Operating Temperature: 0° C to 40° C at 95% relative humidity (non-condensing).<br> The DSP section shall have the following specifi cations:<br> EQ: 6 parametric fi lters per channel with adjustable Q, boost/cut ±15 dB. Also<br> adjustable high and low shelving fi lters.<br> Filters: Highpass and lowpass per channel. Butterworth 12/18 dB per octave<br> and Linkwitz-Riley 24 dB per octave. High and low shelving fi lters, one per<br> channel.<br> Delay: Up to 50 msec total delay per channel.<br> Output Limiter: Prevents clipping and protects loudspeakers. Choice of ?3, ?6,<br> or ?12 dB threshold per channel.<br> Presets: 5 user-defi nable loudspeaker presets and 15 factory-default JBL<br> system presets.<br> Protection shall include the following:<br> DSi-Series amplifi ers shall be protected against shorted, open or mismatched<br> loads; overloaded power supplies; excessive temperature; chain destruction<br> phenomena; excessive output current, and input overload damage. They also<br> protect loudspeakers from input/output DC, large or dangerous DC offsets and<br> turn-on/turn-off transients<br> The chassis shall be steel. Cooling shall be by a proportional speed fan with<br> front-to-rear airfl ow.<br> Dimensions shall be EIA Standard 19-in. rack mount width (EIA RS-310-B), 3.5<br> in. (8.9 cm) high and 12.25 in. (31.11 cm) deep behind mounting surface.<br> Net weight shall be 19 lb (8.6 kg). Shipping weight shall be 22 lb (10.0 kg)</p></td><td>
<p>XB Series - Intelligent Power</p>
<p>Power Without Compromises.<br>The XB is designed for paging, music and alarm signals. Versatile, dynamic <br>and extremely rugged according to IEC286-3. For the highest requirements <br>in safety and quality.<br>Sequential power on, alive contacts and incorporated ground fault detection- <br>the XB is the solution under all conditions. Without the need for additional <br>equipment. For uninterrupted and troublefree operation.</p>
<p>High Tech SMT Design <br>Protection Circuits: DC, LF, HF, Thermal, Short Circuit, Current Limiter, <br>3 ms Muting Delay <br>PHOENIX / Speakon <br>LED Indicators for POWER, SIGNAL, CLIP, PROTECT <br>Temperature controlled, variable speed low noise fans <br>Volume Controls at the back <br>Stereo / Bridged / Parallel Mode <br>Softstart <br>Sequential Remote Power On <br>Alive Contact <br>Ground Lift <br>3 Years Warranty </p>
<p>TECHNICAL DATA:<br>XB 800: 2x 400 W @ 4 Ohm<br>Class: AB<br>Frequency Response: 20 Hz - 20 kHz (0 / -0.3 dB)<br>THD: < 0.025%<br>Signal-to-Noise Ratio: < 103 dB<br>Channel Seperation: > 85 dB<br>Input Sensitivity: +6 dBu<br>Input Clipping: 22 dBu<br>Input Impedance: 20 kOhm<br>Damping Factor: 500 @ 4 Ohm<br>Cooling: 2x fan (temp. reg. variable speed)<br>Weight: 13 kg/(29 lbs) <br>Dimensions: 2 RU / 483 x 88 x 382 mm (19 "acrobat_reader_logo."){kind=logo}
Reviews
There are no reviews yet.