Content | Details
The all metal DB DISPLAY MKII decibel display from American Audio is great for monitoring your sound volume. It also creates a great lightshow in your amp rack. Make sure your speakers stay in great shape by keeping those dBs under control through this monitoring system.
The LED display progresses from green through amber, to red. There are two different operating modes: Dot or Bar. A 5V power supply is included so you can get the unit plug in an running right away. The DB DISPLAY MKII is perfect a stage, church, club or bar install or for a mobile entertainer.
Specifications
• Designed to set in an amp rack to view your decibel level
• Creates a great light show in your amp rack
• Display progresses from green through amber to red
• Sensitivity adjustment on both left and right channels
• 2 separate modes: dot and bar
• Includes 5V power supply
• Line Inputs: Left & Right RCA / Left & Right XLR
• Line Outputs: Left & Right RCA / Left & Right XLR
• Voltage Operation: DC 5V, 500mA Power Supply included
• Dimensions: (LxWxH): 19” x 1.75” x 1.75” / 44.5mm x 483mm x 44.5mm
• Weight: 2.5 lbs. / 1.25kg. | Digital Sound 8928 SPL Meter with Built-In Measurement Mic - calibrated from 300Hz to 8kHz (+/-2dB), 4 control zones in 10dB steps (40-130dB), large LCD display, peak-hold, fast/slow display modes, includes 9V battery.
A superbly designed easy to use sound level meter with features normally only found on more expensive instruments. It has an electret condenser microphone giving virtually instant readings updated every 0.5 seconds on an extra large LCD display.
- 4 measuring ranges, 40 to 70dB, 60 to 90dB, 80 to 110dB or 100 to 130dB
- 0.1dB resolution updated every 0.5 seconds
- Auto ranging or manual range selection
- ʽAʼ & ʽCʼ frequency weighting
- Fast or slow response filters
- 42mm LCD display with quasi-analogue bargraph and function Indicators
- Bargraph in 1dB steps updated every 40ms
- Max hold function to display the highest recorded value
- Min/max memory since power on or last reset
- Low battery indicator
- Auto power off
- Analogue output AC: 0.707 Vrms (at full scale)
- Supplied with battery
|
Cable Tester ACT-100
The Alphaton active remote cable tester can be used for testing either normal short cables or long ones, especially mufticores, wkh connectors not being accessible at one time. The tester is especially suded for fixed installations where cables can not be tested with a standard type cable tester or Ohm meter. Either symmetric and unsymmetric cables can be tested. “Cold" solderings and junction resistances are displayed by color or luminosity changes in three color LED Display. The imprinted fault table incorporates alt important fault conditions, indeed not all possible ones due to their reiatively large number. In case the display is in a state which cannot be found on the imprinted table, it can be looked up in the user's manual. In any case, however, the cabie is in aquite unusable state and should be repaired or replaced.The Alphaton cable tester has a SEND and a REMOTE section. The REMOTE sectionconsistsof two recessed mounted XLR type male or female connector and a stereo phone jack at the right hand side of the tester. Additionally, a separate REMOTE plug is delivered togetherwith the active remote cable tester for testing long cables in fixed installations.
|
The PMBL is a 2 channel passive line level merge box. Each channel has 2 balanced XLR/f inputs. The input signal is merged via a resistor network to a XLR/m output.The top side input is transformer isolated. Possible applications might be the routing of two mixing desks to one power amp or mixing a stereo signal down to mono. Our transformer technology allows for an unbalanced top side input to be sent out balanced.
Specifications:
- Each Channel: Input 1 transformer balanced XLR/f. Symmetrically decoupled through resistors
- Total ohmic value: 2 K Maximum level for THD
|
- Microprocessor-controlled cable tester featuring 3 modes: cable and installed cable test plus test tone mode
- Accepts all standard connectors: XLR, Speakon*, TRS (1/4“, 1/8“), RCA, RJ45, MIDI and USB
- Super-easy operation with intuitive LED display
- Continuity check and intermittent contact detection
- Phantom-power and ground-shield check
- Test-tone generator: 1 kHz or 440 Hz at +4 dBu, -10 dBV or -50 dBV
- Operates with 2 AA size batteries (not included)
- Designed and engineered in Germany
| RS232 Digital Sound Level Meter 8921/8922
- Deluxe super large LCD display w/ affordable price
- Meet IEC60651, type2 class standard
- Unique background noise absorber
- Features w/digital display and analog bar graph
- Professional and rigid design
- Auto / manual ranging ,6 measurement ranges in 10 steps
- Max hold
- Record max / min
- Fast / Slow response mode is selectable
- A /C weighting is selectable
- Easy to calibrate by standard calibrator
- AC/DC analog output
- Tripod mountable
- Backlight function to use in dark area (8922only)
SPECIFICATIONS
Measure range A weight: 30dB~130dB
C weight: 35dB~130dB
Digital display (6 ranges) 30~80, 40~90, 50~100, 60~110, 70-120, 80-130dB
Digital display resolution 0.1dB
Digital updating time 160mS
Quasi-analog bar (6 ranges) 30~80, 40~90, 50~100, 60~110, 70-120, 80-130dB
Quasi-analog bar resolution 1dB
Bar updating time 40mS
Accuracy at 94dB, 1KHz +/-1.5dB
Analog output Microphone AC 0.707Vrms(at full scale); DC 10mV/dB
Dia.6mm electric condenser microphone
Frequency range 31.5Hz~8KHz
Battery life time 30 hours typical
Windscreen LCD YES
size (mm) 42(H)x62(W)
Operating temp. 0~50oC
Operating RH% Humidity
Storage temp. -20~50oC
Storage RH% Humidity
Dimension(mm) Weight 254x77x37
Battery 9V battery x 1pc or 9VDC adaptor
Standard Package Meter/Battery/Manual/carry case
Optional Accessory Computer connection software kit
- DIGITAL DISPLAY WITH ANALOG GRAPH!
- BACKGROUND NOISE ABSORBER !
- BACKLIGHT FOR DARK AREA OPERATION!
- MAX / MIN RECORD, MAX HOLD !
- RS232 INTERFACE !
- MEETS IEC 651, TYPE 2 CLASS !
|
Reviews
There are no reviews yet.