VOX AMPLUG 2 LD Mini amplifier for guitar headphones

Mini amplifier for guitar headphones with advanced analog modeling for authentic high gain emulation with lead tone circuit. AUX input for connection to an external audio source. Operation with 2xAAA batteries.

Overview

With Sennheiserʼs HDVD 800, sound is perfect. The HDVD 800 is able to connect with digital sources and is equipped with a high-quality Burr-Brown digital/analog converter (DAC) that converts digital audio data into analog signals with a resolution of 24 bits and a sampling rate of up to 192 kHz. This enables the HDVD 800 to transmit the entire frequency spectrum of high-end audio sources without any loss of frequencies.

In addition to the symmetrical inputs, the HDVD 800 also has an asymmetrical input socket; incoming signals are symmetrized before further processing takes place. Digital sources can be connected to the rear of the unit via an XLR (AES/EBU) input, optical and coaxial (S/PDIF) digital inputs or USB. All digital inputs accept signals up to 24 bit at 192 KHz*. Designed and manufactured in Germany, this high-end, solid-state amplifier harmonize perfectly and deliver an ultimate acoustic performance when paired with any of Sennheiserʼs audiophile headphones.

Features
D/A transducer for all common formats up to 24 bit / 192 kHz
D/A transducer can be used for CD and DVD players
AES/BU, S/PDIF, USB inputs
Symmetrical (XLR) and asymmetrical (RCA) analog inputs
Symmetrical output
Sockets for four sets of headphones (two of which symmetrical)

Specifications
General

Frequency response
    

 
    

20 Hz - 20  kHz (+0 dB, -1.5 dB)

Signal-to-noise ratio
    

 
    

100  dB (IHF A-weighted, input level control min.)

Channel separation
    

 
    

80 dB between adjacent channels

Line input
    

 
    

Front: 6.3 mm jacks, unbalanced
Rear: RCA connectors, unbalanced

   Input impedance
    

 
    

40 kOhm

   Nominal level
    

 
    

-10 dBV (0.3 V)

Headphone outputs
    

 
    

four 6.3 mm stereo jacks

   Maximum output power
    

 
    

2 x 1.5 W at 8 Ohm (1 channel in use)
2 x 1,2 W an 8 Ohm (four channels in use)

Power supply
        

230 V AC, 50 Hz

Power consumption
    

 
    

10 W

Dimensions (W x H x D)
        

482  mm x 44  mm x 196  mm

Weight
    

 
    

4 kg

HeadAMP - Four Output Stereo Headphone Amp Overview

Most home recordings involve from one to four people, any or all of whom are
going to need headphone monitoring. The monitor amp would be connected
to the tape deck?s headphone output or a mixer output so that the performers
can hear themselves and each other. Of course the same application can apply
to band rehearsals and even home entertainment. HeadAMP provides amplification
and individual volume control for up to 4 headsets. It can be driven by either line-
level or headphone amplifier signals (mono or stereo).

HeadAMP - Four Output Stereo Headphone Amp Specifications:

Signal To Noise Ratio >90dB
IMD (SMPTE) 0.01%
Maximum Input Level +14dBV
Maximum Output Level 20dB per channel
Output Impedance 51 Ohms per channel
Output Connectors Four stereo 1/4? headphone outputs
Power Requirements 12V DC (Adapter included) 
Total Harmonic Distortion

INPUT:    1 audio stereo, 1Vpp/50kΩ on a 6.5mm stereo phone socket.
OUTPUTS:    5 audio stereo, 500mW/8Ω on 6.5mm stereo phone sockets.
AUDIO BANDWIDTH (-3dB):    25kHz.
CONTROL:    5 stereo output level controls (front), 1 mono switch (rear).
GAIN RANGE:    -60dB to +10dB.
S/N RATIO:    78dB.
THD:    0.08% @100mW.
POWER SOURCE:    12V DC, 370mA nom, 1A max.
DIMENSIONS:    16.5cm x 12cm x 4.5cm (6.5” x 4.72” x 1.77”) W, D, H.
WEIGHT:    0.68kg (1.5lbs) approx.
ACCESSORIES:    12V DC power supply.
OPTIONS:    RK-1 19" rack adapter.

• All-passive volume control circuit
• Stereo and AUX inputs
• Dual outputs
• Additional mono output
• Balanced and unbalanced connection
• Integrated high quality headphone amplifier
• Mono, mute and PFL switches
• Stereo volume, AUX and headphone level controls
• Elegant design with solid wood side panels
• Built to last