| Content |
The Apogee X-VID-SYC-GEN Video Expansion Card is designed to fit in the X-Series card slot located in the rear panel of the Apogee Big Ben Master Digital Clock (sold separately). Allows all functions to be controlled from the Big Ben user interface and generates video and provides genlocking function. In genlocking mode the source video-signal will be re-clocked and regenerated, maintaining the same
field and colorburst phase information, but stripped of its line information and replaced by video-black. In slave mode the board will auto-detect the incoming video-standard and configure itself accordingly. The video input is of very high tolerance and will even lock to unstable sources like VCR's.
The Apogee X-VID-SYC-GEN Video Expansion Board has three modes of operation.
•Master mode: The user selects the video format on the frontpanel of the Big Ben. The Big Ben will slave to the generated video signal
•Attended Slave mode: The video board will be configured to autodetect and genlock to the incoming video. The Big Ben will slave to the incoming video signal
•Unattended Slave mode: The video board will be configured to autodetect and genlock to the incoming video. The Big Ben is not clocking to the Video board and therefore both will function independently
Features - Support for PAL, NTSC and 60 Hz B&W standards
- One composite video input and three composite video outputs
- Can operate as a master black-burst generator
- Can operate as genlocking slave device
|
The APH-2n optional accessory pack includes seven tools for use with the H2n. The remote control can be used to start, stop and pause recordings as well as to add marks. The other accessories in the pack are a windscreen that reduces wind and breath noise, a mic clip adapter for use with a mic stand, a tabletop tripod with extendable legs, a padded-shell case, an AC adapter and a USB cable. |
Specifications | General | | Recording media | | CompactFlash (CF) card | | File system | | FAT32 | | Recording format | | BWF (Monophonic, Polyphonic) | | Number of channels | | 8 channels (44.1/48/88.2/96 kHz)
8 channels + stereo mix (44.1/48 kHz)
4 channels (176.4/192 kHz) | | Quantization bit rate | | 16/24 bit | | Sampling frequency | | 44.1/47.952/48/48.048/88.2/96/176.4/192 kHz (47.952/48.048: 48 kHz ± 0.1% pull-down/pull-up) | | Reference clock | | Internal, Word In, Video In, Digital In (AES 1-8 IN, AES A-BIN, ADAT 1-8 IN) | | Type of timecode frame | | 23.976, 24, 25, 29.97DF, 29.97NDF, 30DF, 30NDF | | Limiter | | Attack time: 3 ms
Release time: 300 ms
Threshold: –5 dBFS
Ratio: 32:1 | | Analogue audio inputs and outputs | | The error for nominal and maximum levels is ±1dB for all input and output jacks except the PHONES jack. | | ANALOG INPUT (1-8) | | D-sub 25-pin | | Input impedance | | 10 kOhm | | Nominal input level | | When reference level is –9 dB:
+6 dBu (1.55 Vrms)
When reference level is not –9 dB:
+4 dBu (1.23 Vrms) | | Maximum input level (selectable) | | +15 dBu (4.36 Vrms), +18 dBu (6.16 Vrms), +20 dBu (7.75 Vrms), + 22 dBu (9.76 Vrms), +24 dBu (12.28 Vrms) | | ANALOG INPUT (L/A, R/B) | | XLR-3-31 (1: GND, 2: HOT, 3: COLD) | | Input impedance | | 10 kOhm | | Nominal input level | | When reference level is –9 dB:
+6 dBu (1.55 Vrms)
When reference level is not –9 dB:
+4 dBu (1.23 Vrms) | | Maximum input level (selectable) | | +15 dBu (4.36 Vrms), +18 dBu (6.16 Vrms), +20 dBu (7.75 Vrms), + 22 dBu (9.76 Vrms), +24 dBu (12.28 Vrms) | | ANALOG OUTPUT (1-8) | | D-sub, 25-pin | | Output impedance | | 100 Ohm | | Nominal output level | | When reference level is –9 dB:
+6 dBu (1.55 Vrms)
When reference level is not –9 dB:
+4 dBu (1.23 Vrms) | | Maximum output level (selectable) | | +15 dBu (4.36 Vrms), +18 dBu (6.16 Vrms), +20 dBu (7.75 Vrms), + 22 dBu (9.76 Vrms), +24 dBu (12.28 Vrms) | | ANALOG OUTPUT (A/B) | | XLR-3-32 (1: GND, 2: HOT, 3: COLD) | | Output impedance | | 100 Ohm | | Nominal output level | | When reference level is –9 dB:
+6 dBu (1.55 Vrms)
When reference level is not –9 dB:
+4 dBu (1.23 Vrms) | | Maximum output level (selectable) | | +15 dBu (4.36 Vrms), +18 dBu (6.16 Vrms), +20 dBu (7.75 Vrms), + 22 dBu (9.76 Vrms), +24 dBu (12.28 Vrms) | | PHONES connector | | 6.3-mm standard stereo jack | | Maximum output power | | 45 mW + 45 mW or more (THD+N 0.1 % or less, into 32 Ohm) | | Digital audio inputs and outputs | | DIGITAL IN/OUT (AES/EBU) | | D-sub, 25-pin | | Minimum input voltage | | 2 Vpp | | Maximum input voltage | | 7 Vpp | | Output voltage | | 2–5 Vpp | | Format | | AES3-2003/IEC 60958-4 (AES/EBU) | | DIGITAL I/O (ADAT) | | ADAT optical | | Format | | ADAT | | DIGITAL INPUT A-B | | XLR-3-31 | | Input voltage | | 2–7 Vpp at 110 Ohm | | Format | | AES3-2003 (AES/EBU) | | DIGITAL OUTPUT L-R | | XLR-3-32 | | Output voltage | | 2–5 Vpp at 110 Ohm | | Format | | AES3-2003 (AES/EBU) | | Other inputs and outputs | | RS-422 | | D-sub, 9-pin | | RS-232C | | D-sub, 9-pin | | PARALLEL | | D-sub, 25-pin | | CASCADE IN | | BNC | | Input voltage | | TTL equivalent (5 V) | | Input impedance | | 75 Ohm ±10 %
Allowable frequency deviation of external synchronization: ± 100 ppm | | CASCADE OUT | | BNC | | Output voltage | | TTL equivalent (5 V) | | Output impedance | | 75 Ohm ±10 % | | Sampling frequency | | 44.1/47.952/48/48.048/88.2/96/176.4/192 kHz (47.952/48.048: 48 kHz ± 0.1% pull-down/pull-up) | | TIME CODE IN | | BNC | | Input voltage | | 0.5–5 Vpp | | Input impedance | | 20 kOhm | | TIME CODE OUT | | BNC | | Output voltage | | 2–5 Vpp | | Output impedance | | 600 Ohm ±10 | | WORD/VIDEO IN | | BNC | | Input voltage | | TTL equivalent (5 V) | | Input impedance | | 75 Ohm ±10 %
Allowable frequency deviation of external synchronization: ± 100 ppm | | WORD/VIDEO THRU/OUT | | BNC
OUT/THRU switch included (OUT is for WORD OUT only) | | Output voltage | | TTL equivalent (5 V) | | Output impedance | | 75 Ohm ±10 % | | Sampling frequency (when using WORD) | | 44.1/47.952/48/48.048/88.2/96/176.4/192 kHz (47.952/48.048: 48 kHz ± 0.1% pull-down/pull-up) | | ETHERNET | | RJ45 | | Keyboard | | Mini-DIN (PS/2) | | USB | | USB A-type, 4-pin | | Protocol | | USB2.0 HIGH SPEED (480 Mbit/s) | | Audio performance (analogue input to analogue outp | | Frequency response | | | | 20 Hz - 20 kHz | | ±0,5 dB (all sampling rates) | | at 40 kHz | | +0,5 dB/–2 dB (Fs = 88.2/96 kHz) | | at 80 kHz | | +0,5 dB/–5 dB (Fs = 176.4/192 kHz) | | Distortion | | ≤0.005% (Reference level: –20 dB, input level: +23 dBu, 1 kHz, AES-17LPF) | | S/N ratio | | ≥100 dB(A) (22 kHz LPF) | | Power requirements and other specifications | | Power requirements | | 100–240 V AC, 50–60 Hz | | Power consumption | | 26 W | | Dimensions (W x H x D) | | 483 mm x 88 mm x 288 mm | | Weight | | 4.8 kg | | Operating temperature range | | 5–35 °C |
|
Specifications
General
Recording media CompactFlash card
Tested media SanDisk Extreme IV 4 GB, 8 GB, 16 GB
SanDisk Extreme 4 GB, 8 GB, 16 GB
File system FAT32
File format BWF (single-channel, multi-channel)
Number of audio channels 8 channels at 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz
8 channels + stereo mix at 44.1 kHZ, 48 kHz
4 channels at 176.4 kHz, 192 kHz
Quantization bit rates 16 bit/24 bit
Sampling frequencies 44.1/47.952/48/48.048/88.2/96/176.4/192 kHz
(47.952/48.048: 48 kHz ± 0.1% pull-up/pull-down)
Reference clock Internal, Word in, Video in,
Digital in (CH 1-2, CH 3-4, CH 5-6, CH 7-8)
Timecode frame rates 23.976, 24, 25, 29.97 DF, 29.97 NDF, 30 DF, 30 NDF
Built-in mic Omni directional, monaural
Low cut filter Cut-off frequency: 40/80/120 Hz
Slope: –12/–18 dB/oct
Analogue audio inputs and outputs
MIC IN/LINE IN connectors (1–8) XLR-3-31 (1: GND, 2: HOT, 3: COLD)
Input impedance (LINE) 10 kOhm
Nominal input level (LINE) + 6 dBu (Ref. level: –9 dB)
+ 4 dBu (Ref. level: Other than –9 dB)
Maximum input level (LINE) Selectable: +15 dBu, +18 dBu, +20 dBu, + 22 dBu, +24 dBu
Input impedance (MIC –25) 2.4 kOhm
Minimum input level (MIC –25) –45 dBu
Maximum iput level (MIC –25) +11 dBu
Input impedance (MIC 0) 2.4 kOhm
Minimum input level (MIC 0) –70 dBu
Maximum input level (MIC 0) –14 dBu
LINE OUT connectors (L/R) XLR-3-32 (1: GND, 2: HOT, 3: COLD)
Output impedance 100 Ohm or less
Nominal output level +6 dBu (Ref. level: –9 dB)
Nominal output level +4 dBu (Ref. level: Other than –9 dB)
Maximum output level Selectable: +15 dBu, +18 dBu, +20 dBu, +22 dBu, +24 dBu
PHONES connector 6.3-mm stereo phone jack
Maximum output power 100 mW + 100 mW or more (THD+N: 1 % or less, at 32 Ohm)
Digital audio inputs and outputs
DIGITAL I/O connector D-Sub, 25-pin connector
Format AES3-2003/IEC60958-4 (AES/EBU)
Minimum input voltage 200 mVpp
Maximum input voltage 7 Vpp
Output voltage 3.5 Vpp
DIGITAL OUT connectors BNC
Format AES3-2003/AES-3id-2001 (AES/EBU)
Output voltage 1 Vpp at 75 Ohm
Control inputs and outputs
EXT DC IN connector XLR-4-32 (1: –, 2: NC, 3: NC, 4: +)
Input voltage 11–16 V (2 A)
CASCADE/WORD/VIDEO IN connector BNC
Input voltage 5 V TTL equivalent
Input impedance 75 Ohm ±10 %
Allowable frequency deviation of external sync ±100 ppm
CASCADE/WORD OUT connector BNC
Output voltage 5 V TTL equivalent
Output impedance 75 Ohm ±10 %
Sampling frequencies 44.1/47.952/48/48.048/88.2/96/176.4/192 kHz
(47.952/48.048: 48 kHz ± 0.1 % pull-up/pull-down)
TIME CODE IN connector BNC
Input voltage 0.5–5 Vpp
Input impedance 10 kOhm
TIME CODE OUT connector BNC
Output voltage 2.0 Vpp
Output impedance 600 Ohm
USB port USB B-type, 4-pin
Format USB2.0 HIGH SPEED (480 MBit/s)
KEYBOARD connector Mini-DIN connector (PS/2)
Audio performance
Frequency response (MIC/LINE IN to LINE OUT)
All sample rates 20 Hz – 20 kHz, 0 dB (±0.5 dB)
88.2/96 kHz sample rates at 40 kHz –1 dB (±1.0 dB)
176.4/192 kHz sample rates at 80 kHz –3 dB (+1/–2 dB)
Distortion
LINE IN to LINE OUT 0.003 % or less (–20 dB reference level, +23 dBu input, 1 kHz, AES-17 LPF)
MIC IN (MIC –25) to LINE OUT 0.02 % or less (–20 dB reference level, –10 dBu input, Trim at +20 dB, 1 kHz, AES-17 LPF)
MIC IN (MIC 0) to LINE OUT 0.02 % or less (–20 dB reference level, –35 dBu input, Trim at +20 dB, 1 kHz, AES-17 LPF)
S/N ratio
LINE IN to LINE OUT 110 dB(A) or more (22 kHz LPF)
MIC IN (MIC –25 or MIC 0) to LINE OUT 100 dB(A) or more (22 kHz LPF)
Computer compatibility
Windows Windows XP, Windows Vista, Windows 7
CPU Pentium 300 MHz or faster
Memory 128 MB or more
USB USB 2.0 port
Macintosh Macintosh Mac OS X 10.2 or later
CPU Power PC G3, G4, Intel Mac 266 MHz or faster
Memory 64 MB or more
USB USB 2.0 port
Recommended USB host controller Intel chipset
Power supply and other specifications
Power requirements 100–240 V AC, 50–60 Hz (AC adaptor PS-1225L)
10 AA batteries (Alkaline or NiMH)
External DC battery (DC 11–16 V, 2 A or more)
Battery operation time (continuous operation) Measured according to JEITA standard at 48 kHz, 24-bit, 8 ch playback or recording, phantom power off. Varies with operating conditions.
NP type battery (Li-Ion: 14.8 V/4.6 Ah) About 5 hours
AA type batteries (NiMH) About 2 hours
Power consumption 18 W
Dimensions (W x H x D) 270 mm x 100 mm x 260 mm (excluding protrusions)
Weight 3.65 kg (excluding batteries)
Operating temperature range 0–40 ºC
|
The HD-R1 Solid State Recorder is a two-channel, single rack-mount recording and playback device created with the sound contractor in mind.
Utilizing the highly reliable Compact Flash Card the HD-R1 records 44.1 to 96kHz, 16/24 bit PCM or MP3 files. The ability to control the HD-R1 remotely is provided via RS-232, Parallel, and RJ45 100Mbit Ethernet. File transfer can be accomplished via Ethernet and/or USB (type "A" connector).
To further enhance the HD-R1's feature set, Mic preamps (w/20dB pad) and Phantom Power (rear-panel selectable) have been included. The HD-R1 offers a variety of contractor-friendly I/O options; such as, Unbalanced (RCA), Balanced (XLR and Euroblock), and S/PDIF Digital (Coaxial and Optical).
And of course... the traditional source device features are Power-on-Play, Front Panel Rotary Input Level Controls, Headphone Jack with level control, and a variety of Playback Modes.
* 1U Rack-mount Solid-State Recorder
* Compact Flash Card
* USB host interface for USB Flash Cards
* Audio data formats: PCM (16/24 bit), MP3
* Sampling rates supported: 44.1, 48, 88.2, 96kHz
* Mic/Line XLR (with 20dB pad) balanced I/O
* Phantom Power (rear panel switch and front LED indicator)
* Euroblock terminal (Input and Output)
* Unbalanced RCA (Input and Output)
* Front panel rotary input level controls
* RS-232 interface for control
* RJ45 100Mbit/s Ethernet interface for file transfer and control
* 25-pin parallel remote control interface
* 16 Direct Play via D=SUb25 pin parallel interface
* Power on play (front panel selectable)
* S/PDIF Digital In/Out (Coaxial and Optical)
* Headphone Jack w/level control
* Input through and Auto Fade function
* Input monitoring / mixing of live stereo input along with playback
* Program Play, Folder Play, Shuffle Play, Interval Play modes, etc...
|
For users of just about any TASCAM multitrack, the RC-30P is a wonderful timesaver. Punching in on recordings by hand means you're not ready to play right away. The RC-30P lets you play straight through. While automated punch-ins available on some recorders are also helpful, most punches can be done with the simple and efficient precision of the RC-30P, saving you time.
|
Reviews
There are no reviews yet.