Content |
The design of the HDA range draws upon all of Arcam’s experience as one of the UK’s most respected audio companies, to produce Arcam’s best performing range of audio products yet – using the best quality components and engineering practices, the HDA range is designed and built to give you years of listening enjoyment.
- Extremely efficient class A/B amplification
- 50W of power per channel
- 5 analogue inputs including phono
- 3 digital inputs
- 32-bit DAC,Sabre ESS9016K2M
- Full I/P control
- Total harmonic distortion + noise = 0.003%
SA10
In any amplifier, the signal path is at the mercy of anything that creates noise within the unit. Thus, we spare no expense in using only the most high-quality components, even if it means the cost of our power supplies overtaking that of everything else.
The result, of course, is worth every penny.
A singer’s sharp intake of breath before hitting the chorus, a guitarist’s fingers sliding against the strings – it’s those seemingly minor details that can bring music to life. Fish out one of your all-time favourite albums and play it through a Bluetooth speaker, and guess what? Its sounds like a Bluetooth speaker. Play it through the SA10, and it’s as close to hearing the artist’s performance as you’re likely to get. There’s always joy in digging out an old recording you haven’t heard in years. With the HDA range, it’ll feel like hearing it forthe first time. |
Ti 120 SIGN.
Special power and output transformer
from BHS uk and Mundof M-Cap
signal capasitors
Integrated tube amp.Four line inputs.
2X12AU7, 4x KT 88, 2x12AX7
2x6SN7 75 Wrms per chan.4-8 ohm.
Class AB push-pull.Remote control inc.
Negative feedback on/of switch.
echnical specification
|
|
|
Integrated Amplifier
|
Frequency response:
|
10 Hz - 50 kHz (± 0.5 dB)
|
Total harmonic distortion (THD):
|
1 % (1 kHz)
|
Signal-to-noise ratio:
|
92 dB
|
Input Impedance:
|
100 kOhm
|
|
|
Vacuum tube:
|
4x KT88/EL34, 2x 12AU7, 2x 12AX7, 2x 6SN7
|
Dimensions W x H x D:
|
440 x 220 x 390 mm
|
Weight:
|
28 kg
|
Accessories:
|
Remote Control
|
Input Terminals:
|
Tape, CD, AUX, Tuner
|
Output terminals:
|
Tape out
|
Circiut:
|
Class A/B P.P.
|
Colour:
|
Chassis chrome, transformer black
|
Colour front:
|
black, silver
|
Sensitivity
|
590 mV
|
Output Impedance:
|
4 Ohm, 8 Ohm
|
Power Output:
|
2 x 70 Watt @ 1 % THD
|
Consumption:
|
max. 380 Watt
|
Highlights
|
switchable reduction of feedback
|
| For a long time, installers worldwide have been unhappy with consumer electronics and they were looking for a professional integrated amplifier for use in commercial environments, boardrooms or small businesses designed for 24/7 operation. Therefore Apart developed the CONCEPT1, a stereo or two mono channel (2 x 80 watts @ 4 ohms) amplifier for small and medium-sized projects.
This CONCEPT1 2-zone integrated stereo amplifier can operate with one stereo zone, two volume-linked mono zones or two individual-volume mono zones. The unit can be controlled via RS232 what makes integration into your AV solution possible. The built-in limiters and system design guarantee a failsafe solution 24 hours a day, 7 days a week.
To make the life of the end-user as easy as can be, the CONCEPT1 has user settings and installer settings. Only the absolute
19" (483 mm wide) rack mounting |
Yes |
height- rack units (1U=44 mm) |
2 U |
depth (build in) |
293 mm |
power supply |
230 VAC volts |
power consumption (max) |
< 200 watts |
output power RMS 4 ohms |
2 x 80 watts |
output power RMS 8 ohms |
2 x 60 watts |
music program power |
100 watts |
minimum impedance load |
4 ohms |
zone outputs |
2 |
MIC inputs balanced |
1 |
line input unbalanced |
4 |
tone control |
Yes |
RS232 (serial communication port) |
Yes |
priority switch |
2 |
priority levels |
1 |
cooling system |
convection |
applicable low impedance |
Yes |
|
Class XD™ amplification designed to eliminate crossover distortion at low signal levels New balanced volume topology controllable in 1dB steps, giving very fine control, and superbly accurate channel balance Audiophile grade oversize toroidal transformer and substantial extruded heatsink allowing 2 x 120 Watts RMS into 8 Ohms or 2 x 200W into 4 ohms. Separate transformer taps for left and right channels, twin rectifiers and separate PSUs for dual mono operation of the left and right power amplifiers A separate toroidal transformer supplies the preamp making the 851A effectively a Pre and Power amp combination in one box CAP5 protection technology for trouble free operation Acoustically damped full metal chassis with thick brushed aluminium front panel Customisable front panel display Balanced and unbalanced analogue audio inputs for superior connectivity RS232 controllable Eco-friendly Available in black and silver finishes
|
Power Output One Channel Driven :275 watts
Dimensions (Without Brackets, Including Feet) :17-1/16" W x 9-5/8" D x 3-11/16" H (43.34 cm W x 24.45 cm D x 9.37 cm H)
Weight | Metric :28 lbs | 12.70 kg
Dimensions (With Brackets, Feet Removed) :19-1/16" W x 9-5/8" D x 3-7/16" H (41.42 cm W x 24.45 cm D x 8.73 cm H)
Finish :Available in both silver and black
Power Output Two Channels Driven :230 watts each
|
Τi 60 tube
Integrated tube amp.Four line inputs.
2X12AU7, 4x EL34, 1x12AX7
35 Wrms per chan.4-8 ohm.
Class AB push-pull
Remote control included.
Technical specification
|
|
|
Integrated Amplifier
|
Frequency response:
|
10 Hz - 50 kHz (± 0.5 dB)
|
Total harmonic distortion (THD):
|
1 % (1 kHz)
|
Signal-to-noise ratio:
|
92 dB
|
Input Impedance:
|
100 kOhm
|
|
|
Vacuum tube:
|
4x KT88/EL34, 2x 12AU7, 2x 12AX7, 2x 6SN7
|
Dimensions W x H x D:
|
440 x 220 x 390 mm
|
Weight:
|
28 kg
|
Accessories:
|
Remote Control
|
Input Terminals:
|
Tape, CD, AUX, Tuner
|
Output terminals:
|
Tape out
|
Circiut:
|
Class A/B P.P.
|
Colour:
|
Chassis chrome, transformer black
|
Colour front:
|
black, silver
|
Sensitivity
|
590 mV
|
Output Impedance:
|
4 Ohm, 8 Ohm
|
Power Output:
|
2 x 70 Watt @ 1 % THD
|
Consumption:
|
max. 380 Watt
|
Highlights
|
switchable reduction of feedback
|
|
Reviews
There are no reviews yet.