ARTSOUND A8862 LASERGRIP THERMOMETER

 ARTSOUND A8862 LASERGRIP THERMOMETER

Temperature range: -32 C - 550 C
Accuracy: 1,5%
Power supply: 9V
Weight: 258gr

Cable Tester ACT-100

The Alphaton active remote cable tester can be used for testing either normal short
cables or long ones, especially mufticores, wkh connectors not being accessible at
one time. The tester is especially suded for fixed installations where cables can not
be tested with a standard type cable tester or Ohm meter. Either symmetric and
unsymmetric cables can be tested.
“Cold" solderings and junction resistances are displayed by color or luminosity changes
in three color LED Display. The imprinted fault table incorporates alt important fault
conditions, indeed not all possible ones due to their reiatively large number. In case the
display is in a state which cannot be found on the imprinted table, it can be looked up in
the user's manual. In any case, however, the cabie is in aquite unusable state and should
be repaired or replaced.The Alphaton cable tester has a SEND and a REMOTE section.
The REMOTE sectionconsistsof two recessed mounted XLR type male or female connector
and a stereo phone jack at the right hand side of the tester. Additionally, a separate REMOTE
plug is delivered togetherwith the active remote cable tester for testing long cables in fixed
installations.

This is an on-the-road tool you certainly can't miss in your gearbox! A nifty, handy cabletester, which allows you to check up to six (welding) connections and gives you a visual readout by 2 rows of 6 LED's. The checking itself is done manually per connected pin. A LED will light up to indicate what pin is connected correctly on which side. A short-circuit check with a red LED and audio-warningsignal is also included. On the left and right side you'll find inputs for 6,3 symm. jack, BNC, RCA, 5p. DIN, 5p. XLR, 3p. XLR and Neutrik® Speakon®.

Palmer Pro MCT DMX 3-pin and 5-pin DMX and XLR cable tester MCT DMX This cable tester checks 3-pin and 5-pin DMX cables for continuity in fully automatic or manual pin selection modes. Pin connection status of the male and female cable ends is indicated by two rows of bright LEDs. In addition, the unitʼs 3-pin connectors can also be used to test XLR microphone cables. The DMX Cable Tester comes with two L-brackets for variable mounting options.

• Tests 3-pin and 5-pin DMX cables for continuity
• Also tests 3-pin XLR microphone cables
• Automatic test mode or manual pin 1 - 5 selection
• LED indicators
• Mounting brackets included

The tester allows to makea fast test connection for many type of audio and
lighting cable, checking up to 7 connections (Neutrik? , Speakon?, XL3,
XLR5, DIN RCA, Jack and BNC). Two rows of LEDs will light up to indicate
which pin is connected correctly. a red lit LED and beep indicate short-circuited
connection

Specifications:
Battery: PP3 9V(not included) Accessory: Short Tester pinx2(included)
Net Weight: 0.71Kg Dimensions: 178x121x44mm

The MiniSPL is the perfect accessory to the Acoustilyzer & Minilyzer for
acoustical measurements.
  The MiniSPL is a battery powered measurement microphone. Together
with the Acoustilyzer or Minilyzer, it forms an acoustical analyzer and integrating
sound level meter. Additionally it may be operated as a stand-alone microphone
e.g. connected to a balanced audio-line, a microphone-input or a sound-card.
  
Product-details
? Battery powered
? Factory-set sensitivity
? No phantom power required
? 1/2" microphone, class 2 acc. IEC 61672
? Omni-directional
? Supplied with mic clamp, wind protection
? Typical frequency response included
MiniSPL together with Acoustilyzer:
? SPL Meter / RTA
? Reverberation Time RT60
? Delay Time
? FFT Analyzer
? Speech Intelligibility STI-PA
MiniSPL together with Minilyzer:
? Measurements: SPL, min./max., Leq
? 1/3rd octave spectrum analyzer