Content | Non-Contact Laser Thermometer LCD Digital IR Infrared Thermometer GM400 Temperature Meter Gun Point -50~400 Degree
This infrared thermometer USES non-contact infrared sensing technology, the target of safety, preparation, fast, reliable measurement, is widely used in measuring the mechanical, chemical, ceramics, light industry, food, metallurgy, electric power, high temperature heat treatment and other industries, dangerous and difficult to close to the surface temperature measurement. Temperature measurement is widely used in the school laboratory and home.
Objects of any temperature greater than absolute zero radiation infrared energy, this energy to around at the speed of light transmission, infrared lens collects and gathers the infrared energy to the sensor, the sensor produces a low output voltage, the voltage is proportional to the temperature of the target object, voltage after processing for the temperature value.
- Not recommended for human use.
Main features:
1. Temperature range: -50 ℃ ~ 400 ℃ (-58 ℉ ~ 752 ℉)
2. Accuracy: ± 1.5 ° C (± 2.7 ° F) OR ± 1.5% ° C
3. ℃ / ℉ conversion selection function
4. Display resolution: 0.1 ℃ or 0.1 ℉
5. Working environment: 10 ℃ - ~ 40 ℃ (50 ℉ ~ 104 ℉), relative humidity: 10 ~ 90RH no condensation
6. Storage temperature: -10- ~ 40 ℃ (14 ℉ ~ 104 ℉)
7. Detection time: ≤ 0.8second
8. Distance coefficient ratio: 12: 1 (distance and measuring point size ratio)
9. Emissivity: Preset: 0.95
10. Power supply: 2 7 batteries (purchase, replace the battery more convenient)
11. Battery life of about 12 hours
12.LED backlight (easy to use at night)
13. Automatic shutdown function (about 10 seconds)
Model |
INFRARED THERMOMETER-GM400 |
Temperature range |
-50 ℃ ~ 400 ℃ (-58 ℉ ~ 752 ℉) |
Accuracy |
± 1.5 ° C (± 2.7 ° F) OR ± 1.5% ° C |
Display resolution: |
0.1 ℃ or 0.1 ℉ |
Working environment |
10 ℃ - ~ 40 ℃ (50 ℉ ~ 104 ℉), relative humidity: 10 ~ 90RH no condensation |
Storage temperature |
-10- ~ 40 ℃ (14 ℉ ~ 104 ℉) |
Detection time |
≤ 0.8second |
Distance coefficient ratio |
12: 1 (distance and measuring point size ratio) |
Emissivity Preset: |
0.95 |
Power supply |
2 7 batteries (purchase, replace the battery more convenient) |
Battery life |
12 hours |
LED |
LED backlight |
Automatic shutdown function |
about 10 seconds |
|
Minirator MR1 is the powerful analog audio generator providing a comprehensive
set of analog audio test signals required in a professional audio environment.
This handy audio generator enables you to stimulate any analog device with a
broad range of appropriate signals like sine wave, pink noise, white noise,
sweeps and many others, for performance checking, maintenance and repairs.
Convenient, reliable and optimized - Minirator fits into your pocket as well as in
your budget.
Product-details
Signals:
? Sine Wave
? Square Wave
? Frequency Sweep
? White Noise
? Pink Noise
? Polarity Test Signal
Features:
? 20Hz to 20kHz, adjustable
in 1/3rd octave steps
? Level adjustable
? Low distortion
|
- Measures impedance of speaker lines up to 100k ohms
- Batteries: four (AA)
- Zero adjustment for accuracy on all ranges
- Easy to read meter calibrates directly in ohms
- Includes carrying case, test leads and impedance to power reference chart
- Five year warranty
|
The tester allows to makea fast test connection for many type of audio and lighting cable, checking up to 7 connections (Neutrik? , Speakon?, XL3, XLR5, DIN RCA, Jack and BNC). Two rows of LEDs will light up to indicate which pin is connected correctly. a red lit LED and beep indicate short-circuited connection
Specifications: Battery: PP3 9V(not included) Accessory: Short Tester pinx2(included) Net Weight: 0.71Kg Dimensions: 178x121x44mm | Tests XLR, 1/4 in., 1/8 in., TT, RCA and MIDI connectors.
The intelligent, CPU-controlled CT100 accepts virtually any connector type:
XLR, mono and TRS phone (1/4 in., 1/8 in., TT), RCA and MIDI. It shows
which input pin is connected to which output pin. Separate LEDs indicate
proper shield connection and phantom power presence. The CT100 also
offers an installed cable test mode and a continuity check plus a test tone
generator.
Features
3 modes: cable test mode, installed cable test mode, and test tone mode
Accepts XLR, mono and stereo TRS phone (1/4 in., 1/8 in., TT),
RCA and MIDI Connectors
Continuity check
Intermittent detect
Phantom power detect
Grounded shield detect
Test tone generation (1 kHz and 440 Hz)
Battery operation (requires 2 AA alkaline batteries) | Details
The all metal DB DISPLAY MKII decibel display from American Audio is great for monitoring your sound volume. It also creates a great lightshow in your amp rack. Make sure your speakers stay in great shape by keeping those dBs under control through this monitoring system.
The LED display progresses from green through amber, to red. There are two different operating modes: Dot or Bar. A 5V power supply is included so you can get the unit plug in an running right away. The DB DISPLAY MKII is perfect a stage, church, club or bar install or for a mobile entertainer.
Specifications
• Designed to set in an amp rack to view your decibel level
• Creates a great light show in your amp rack
• Display progresses from green through amber to red
• Sensitivity adjustment on both left and right channels
• 2 separate modes: dot and bar
• Includes 5V power supply
• Line Inputs: Left & Right RCA / Left & Right XLR
• Line Outputs: Left & Right RCA / Left & Right XLR
• Voltage Operation: DC 5V, 500mA Power Supply included
• Dimensions: (LxWxH): 19” x 1.75” x 1.75” / 44.5mm x 483mm x 44.5mm
• Weight: 2.5 lbs. / 1.25kg. |
Reviews
There are no reviews yet.