| Content | 6-channel dimmer for LED calibrate minimum power 1w
Single phase Dimmer DMX – 512 High quality 6 channels 400watt each, special for LED sources adjustable from 3 watts. On the front panel it has 6 protection fuses of 2 A for each channel. On the back of the Dimmer, the connection is made with detachable terminals. You have the option of manual check to adjust your lighting percentage.
D46 DMX INSTRUCTIONS FOR USE
The dimmer is connected to a single-phase supply with a Shuko socket.
The dimmer works digitally and has 6 channels. The DMX connection is made on the front panel with a male XLR 3 PINS input (1 pins earth – 2 pins ( – ) and 3 pins (+ ), DMX continuity is made with XLR female with the same connections and you can connect DMX to terminals that are on the back of the dimmer.
The red led shows the voltage supply, the green led shows the DMX communication (DATA).
The display shows the number of DMX channels (001-512) channels. The up / down buttons raise or lower the number of channels (eg 001, 002, 003, ...).
The ( + /- ) manual check buttons are used to check the channels
The connection of the loads to the output is done with screw terminals. The indications are L (phase), N (neutral) and G (ground) and the power of each channel is 400 Watts.
After connecting the dimmer, open the ON-OFF switch. The red led lights up and the display shows an error (i.e. there is no communication). To start communication with the dimmer, connect the DMX in input plug to the console.. The display shows 001 and the DATA led lights up. Depending on what channel the display is showing, that channel of the console starts the dimmer.
If the dimmer shows 001 it means that the dimmer is connected to the console from channel 1-6. If it shows 002 it is connected to channels 2-7. If it shows 003 it is connected to channels 3-8 and so on.
If you want to connect more dimmers from the DMX OUT plug, connect your next dimmer or to the In-Out terminals on the back..
If any LED does not light up, it means that there is an error in the connection. If you want to check the dimmer channels (manual check), press the buttons (+ / –) for 3 seconds together. Then the display shows . By pressing the up button, you continuously raise the lighting percentage of the channel. Control the other channels in the same way by pressing the (+ / – ) buttons.
If you want to control all channels together in master position then the display should show the number .
To restore the dimmer to its original state after the manual check, press the (+ / – ) buttons at the same time. Minimum control load 3 watts. |
Digital Programmable dimmer. 6 DMX channels. 24 programmable scenes.LCD display.
Power failure memory.Each channel can be programmed with preheat level, maximum
output level, control curve and fade time.
Channel output (Single phase) 10A/Ch Total 60A.
Channel output (Three phases) 10 A/Ch Total 20A. |
Digital 6-channel dimmer pack - Universal dimmer pack for professional use
- Can be operated 1-phase or 3-phase
- 6 x 10 A
- DMX-control or analogue control possible
- The DMX-starting address can be adjusted on the device
- Synchronisation of several DPX-610 S possible via DMX
- Adjusting the lamp pre-heat
- All modes are displayed via LEDs and the display
- With automatic circuit breaker per channel
- Channel-outputs on the rearpanel via safety sockets
|
Zero88 Betapack3 Schuko + DMX
Excellent value 6 channel dimmers for multipurpose use
The Betapack 3 range of digitally controlled dimmer packs offer one of the most cost effective and versatile solutions to dimming currently available.
Manufactured to the highest professional standards, this comprehensive range of 6 x 10 Amp packs includes variants with sockets to match most global standards.
The Betapack 3 range is available with MCB?s per channel giving you peace of mind and maximum protection.
The versatility of the Betapack 3 means it can be 19" rack or wall mounted using the brackets supplied or made portable by adding the optional "Easicarry" kit consisting of a handle and four feet. Its legendary reliability and durability make it the dimmer of choice for a huge variety of venues worldwide.
| Features |
- MCB protection as standard
- Isolated DMX input
- Patchable per channel
- Preheat, Topset and Dimmer Law selectable per channel
- 12 programmable backup memories
- 3 programmable 99-step sequences with adjustable times
- Auto DMX termination when loop-through plug is removed
- Auto frequency tracking
|
- Lock and Reset functions
- Temperature monitoring and progressive overheat shutdown
- Convection cooled
- DMX Status indication
- 19" Rack and Wall mounting brackets included
- Easy to service- common service operations need only a screwdriver
| |
![]() ![]() ![*]() Universal power-pack for professional use ![*]() Can be operated 1-phase or 3-phase 12 x 10 A ![*]() DMX-control or analogue control possible ![*]() Synchronisation of several DPX-1210 possible via DMX ![*]() The channels can either be dimmed or switched ![*]() Adjusting the lamp pre-heat for the dimmed channels ![*]() All modes are displayed via LEDs and the display ![*]() With automatic circuit breaker per channel ![*]() Channel-outputs on the rearpanel via pole connectors ![*]() technical specifications: ![*]() Power supply: 230-380 V AC, 50 Hz ~ ![*]() Max. power output: 27600 W ![*]() Max. current: 120 A ![*]() Number of control-channels: 12 ![*]() Max. output/channel: 2300 W ![*]() Max. current/channel: 10 A ![*]() Integrated programs: 12 ![*]() DMX in / out ![*]() Analogue input: 15-pin Sub-D socket, 12 channels, 0/10 V DC ![*]() Output sockets: Via pole connectors ![*]() Fuse: 12 x F 10 A, 230 V ![*]() Dimensions (WxDxH): 482 x 485 x 176 mm ![*]() 19" mounting dimensions with 4 u ![*]() Minimum mounting depth: 500 mm ![*]() Weight: 27 kg
| 2U digital Dimmer, 6 channels with 10A current each, LCD display, single or full adjusting lamp pre-heat, Softpatch, manual channel operation, Curve: Linear, Square, Switch, DMX 512 in/out 3-pin XLR or analogue 0-10V, 1-phase or 3-phase 380-230V AC, 50Hz, 10Α automatic circuit breaker per channel. Dimensions: 410x482x95mm. Weight: 8kg. (70064122). Applications: live / disco / bar / restaurant / theaters.
6x10A dimmer for DMX & analog signals, connection via terminal blocks
- Universal dimmer pack for professional use
- Can be operated 1-phase or 3-phase
- 6 x 10 A
- DMX control or analog control possible
- The DMX-starting address can be adjusted on the device
- Synchronization of several devices possible via DMX
- Adjusting the lamp pre-heat
- All modes are displayed via LEDs and the display
- With automatic circuit breaker per channel
- Channel-outputs on the rearpanel via pole connectors
- Only for professional use
- Preprogrammed 12 chasers
- Can be operated in 6 CH mode
- Controlling by Analog 0-10 V; stand-alone; DMX
- (19") 48.3 cm rack installation 2 U
| Power supply: |
230/380 V AC, 50 Hz |
| Output power: |
Max. 13800 W
Max. 2300 W per channal |
| Output current: |
Max. 60 A |
| Power connection: |
Mains input via screw terminal |
| Power output: |
Screw terminal |
| Power output fuse per channel: |
C 10 A Fuse resettable |
| Programs: |
Preprogrammed 12 Chasers |
| DMX channels: |
6 |
| DMX input: |
3-pin XLR (M) mounting version |
| DMX output: |
3-pin XLR (F) mounting version |
| Control: |
Analog 0-10 V; stand-alone; DMX |
| Control channels: |
6 |
| Color: |
Black |
| Housing design: |
(19") 48.3 cm rack installation 2 U |
| Dimensions: |
Width: 48,3 cm
Depth: 41 cm
Height: 8,9 cm |
|
Reviews
There are no reviews yet.