ATEL D46 LED Dimmer 6 Channel O LIGHTING

205.00 incl. GR VAT

Only 3 left in stock (can be backordered)

EAN: N/A
Installments calculation
CompareAdd to wishlist Submit Better Price
6-channel dimmer for LED calibrate minimum power 1w Single phase Dimmer DMX – 512 High quality 6 channels 400watt each, special for LED sources adjustable from 3 watts. On the front panel it has 6 protection fuses of 2 A for each channel. On the back of the Dimmer, the connection is made with detachable […]

 

Read more

6-channel dimmer for LED calibrate minimum power 1w

Single phase Dimmer DMX – 512 High quality 6 channels 400watt each, special for LED sources adjustable from 3 watts. On the front panel it has 6 protection fuses of 2 A for each channel. On the back of the Dimmer, the connection is made with detachable terminals. You have the option of manual check to adjust your lighting percentage.

D46 DMX INSTRUCTIONS FOR USE

 

The dimmer is connected to a single-phase supply with a Shuko socket.

The dimmer works digitally and has 6 channels. The DMX connection is made on the front panel with a male XLR 3 PINS input (1 pins earth – 2 pins ( – ) and 3 pins (+ ), DMX continuity is made with XLR female with the same connections and you can connect DMX to terminals that are on the back of the dimmer.

The red led shows the voltage supply, the green led shows the DMX communication (DATA).

The display shows the number of DMX channels (001-512) channels. The up / down buttons raise or lower the number of channels (eg 001, 002, 003, …).

The ( + /- ) manual check buttons are used to check the channels

The connection of the loads to the output is done with screw terminals. The indications are L (phase), N (neutral) and G (ground) and the power of each channel is 400 Watts.

After connecting the dimmer, open the ON-OFF switch. The red led lights up and the display shows an error (i.e. there is no communication). To start communication with the dimmer, connect the DMX in input plug to the console.. The display shows 001 and the DATA led lights up. Depending on what channel the display is showing, that channel of the console starts the dimmer.

If the dimmer shows 001 it means that the dimmer is connected to the console from channel 1-6. If it shows 002 it is connected to channels 2-7. If it shows 003 it is connected to channels 3-8 and so on.

If you want to connect more dimmers from the DMX OUT plug, connect your next dimmer or to the In-Out terminals on the back..

If any LED does not light up, it means that there is an error in the connection. If you want to check the dimmer channels (manual check), press the buttons (+ / –) for 3 seconds together. Then the display shows . By pressing the up button, you continuously raise the lighting percentage of the channel. Control the other channels in the same way by pressing the (+ / – ) buttons.

If you want to control all channels together in master position then the display should show the number .

To restore the dimmer to its original state after the manual check, press the (+ / – ) buttons at the same time. Minimum control load 3 watts.

Weight 2.00 kg

Reviews

There are no reviews yet.

Be the first to review “ATEL D46 LED Dimmer 6 Channel O LIGHTING”

Your email address will not be published. Required fields are marked *

Quick Comparison

ATEL D46 LED Dimmer 6 Channel O LIGHTING removeEUROLITE DPX-1210 MODULAR DIMMER 12X10A/DMX & 0-10V removeWORK WD 1215 DMX 12 CHANNELS DIGITAL DIMMER removeEUROLITE DPX-620 6CH 20A DMX and Analog Dimmer Pack removeLITEPUTER DX-626 6 CHANNELS DIMMER 20A removeSHOWTEC 50901 DDP-616 6 Channel Digital Dimming Pack 16A/Ch remove
NameATEL D46 LED Dimmer 6 Channel O LIGHTING removeEUROLITE DPX-1210 MODULAR DIMMER 12X10A/DMX & 0-10V removeWORK WD 1215 DMX 12 CHANNELS DIGITAL DIMMER removeEUROLITE DPX-620 6CH 20A DMX and Analog Dimmer Pack removeLITEPUTER DX-626 6 CHANNELS DIMMER 20A removeSHOWTEC 50901 DDP-616 6 Channel Digital Dimming Pack 16A/Ch remove
Image50915 showtec dimmer 6channel ddp-616 16a
SKUD46 OLIGHTDPX-1210WD 1215 DMXDPX-62063000150901
Rating
Price 205.00 incl. GR VAT 906.44 incl. GR VAT 1,380.74 incl. GR VAT 677.12 incl. GR VAT 640.00 incl. GR VAT 580.00 incl. GR VAT
Stock

Only 3 left in stock (can be backordered)

In stock

In stock

Available on backorder

In stock

Only 1 left in stock

AvailabilityOnly 3 left in stock (can be backordered)In stockIn stockAvailable on backorderIn stockOnly 1 left in stock
Add to cart

Add to cart

Add to cart

Add to cart

Add to cart

Add to cart

Add to cart

Description• Redesigned and improved 6-channel dimmer • Ideal dimmer for touring and fixed installation • Clear LCD display for all menu settings • Strong 19" housing • Variable Fan speed cooling system
Content6-channel dimmer for LED calibrate minimum power 1w Single phase Dimmer DMX – 512 High quality 6 channels 400watt each, special for LED sources adjustable from 3 watts. On the front panel it has 6 protection fuses of 2 A for each channel. On the back of the Dimmer, the connection is made with detachable terminals. You have the option of manual check to adjust your lighting percentage. D46 DMX INSTRUCTIONS FOR USE   The dimmer is connected to a single-phase supply with a Shuko socket. The dimmer works digitally and has 6 channels. The DMX connection is made on the front panel with a male XLR 3 PINS input (1 pins earth – 2 pins ( – ) and 3 pins (+ ), DMX continuity is made with XLR female with the same connections and you can connect DMX to terminals that are on the back of the dimmer. The red led shows the voltage supply, the green led shows the DMX communication (DATA). The display shows the number of DMX channels (001-512) channels. The up / down buttons raise or lower the number of channels (eg 001, 002, 003, ...). The ( + /- ) manual check buttons are used to check the channels The connection of the loads to the output is done with screw terminals. The indications are L (phase), N (neutral) and G (ground) and the power of each channel is 400 Watts. After connecting the dimmer, open the ON-OFF switch. The red led lights up and the display shows an error (i.e. there is no communication). To start communication with the dimmer, connect the DMX in input plug to the console.. The display shows 001 and the DATA led lights up. Depending on what channel the display is showing, that channel of the console starts the dimmer. If the dimmer shows 001 it means that the dimmer is connected to the console from channel 1-6. If it shows 002 it is connected to channels 2-7. If it shows 003 it is connected to channels 3-8 and so on. If you want to connect more dimmers from the DMX OUT plug, connect your next dimmer or to the In-Out terminals on the back.. If any LED does not light up, it means that there is an error in the connection. If you want to check the dimmer channels (manual check), press the buttons (+ / –) for 3 seconds together. Then the display shows . By pressing the up button, you continuously raise the lighting percentage of the channel. Control the other channels in the same way by pressing the (+ / – ) buttons. If you want to control all channels together in master position then the display should show the number . To restore the dimmer to its original state after the manual check, press the (+ / – ) buttons at the same time. Minimum control load 3 watts.

* Universal power-pack for professional use

* Can be operated 1-phase or 3-phase 12 x 10 A

* DMX-control or analogue control possible

* Synchronisation of several DPX-1210 possible via DMX

* The channels can either be dimmed or switched

* Adjusting the lamp pre-heat for the dimmed channels

* All modes are displayed via LEDs and the display

* With automatic circuit breaker per channel

* Channel-outputs on the rearpanel via pole connectors

* technical specifications:

* Power supply: 230-380 V AC, 50 Hz ~

* Max. power output: 27600 W

* Max. current: 120 A

* Number of control-channels: 12

* Max. output/channel: 2300 W

* Max. current/channel: 10 A

* Integrated programs: 12

* DMX in / out

* Analogue input: 15-pin Sub-D socket, 12 channels, 0/10 V DC

* Output sockets: Via pole connectors

* Fuse: 12 x F 10 A, 230 V

* Dimensions (WxDxH): 482 x 485 x 176 mm

* 19" mounting dimensions with 4 u

* Minimum mounting depth: 500 mm

* Weight: 27 kg

WD 1215 DMX
 
12 channels digital module dimmer. This dimmer has incorporated a 32 bit high power
microcomputer with aa time processing unit. Each channel can be programmed with the
adress, a control curve, the limitation, the preheat of the lamps and the loadcheck. 12
internal memories. Can be linked with oyher dimmers. Protections: Short circuit, power
failure memory. Alarm of over voltage. Temperature with switch off. Electronic fuse and
loadcheck. 10A per channel. 3 phase connection.
Dimensions: 483x178x436 mm. Weight: 31 Kgs.

  • Universal dimmer pack for professional use
  • Can be operated 1-phase or 3-phase
  • 6 x 20 A
  • DMX-control or analogue control possible
  • The DMX-starting address can be adjusted on the device
  • Synchronisation of several DPX-620 possible via DMX
  • Adjusting the lamp pre-heat
  • All modes are displayed via LEDs and the display
  • With automatic circuit breaker per channel
  • Channel-outputs on the rearpanel via pole connectors
  • Only for professional use
Power supply: 230-380 V AC, 50 Hz ~
Max. power output: 27600 W
Max. current: 120 A
Number of control channels: 6
Max. output/channel: 4600 W
Max. current/channel: 20 A
Integrated programs: 12
Output sockets: via pole connectors
Circuit breaker: 6 x C 20 A
Dimensions (WxDxH): 420 x 482 x 95 mm
  Rack installation with 2 U
Minimum mounting depth: 500 mm
Weight: 8 kg

 

DX-626 is a sophisticated DMX 6 Channel dimming pack. Its C3 liner dimming curve
ensures the accuracy of dimming effects on each fader scale. Each channel provides
20A output and is equipped with a 25A high-speed magnetic breaker. DX-626 has a
thermo-controlled fan which will activates automatically when the temperature is over
35°C (95°F). It can keep the system?s temperature in a safe range and reduce dust
accumulation. The 6 dimming sliders on the control panel are convenient for testing.
In addition to DMX input, it also has analog 0 ? 10 V DC input.

Features:
6 channels, each 20A.
C3 liner dimming curve.
Automatically detect power frequency (50Hz/60Hz) in different area and stabilizes the
dimming output.
The thermo-controlled fan will be activated automatically when the temperature is over 35°C
(95°F), stop the output when over 75°C° (167°F) and restart output when below 65°C (149°F). 
Self-testing function to test without a console. 
Each channel has individual 0-6% preheat setting for protecting loads. 
Each channel can be set as dimming or non-dimming.

 
Power supply 100?120V AC, 200?240V AC  50/60 Hz, 3?4w (1?3w optional)
Output       Maximal 20A per channel, total 20A.
DMX signal input/ output DMX512 
DMX signal connector  XLR-5pin, XLR-3pin, 6p4c phone jack connector 
Analog signal input  0 --- 10V DC 6 Channels ( 9 pin D-type, female )
Analog signal power input   DC 0-10V 
Analog signal connector   D-Type Plug 9Pin(F) 
Analog input channel   9 channels
Preheat setings 0 --- 6%
Dimension 19? 2U, 482(W) x 88(H) x 313(D) mm
Weight         8  Kg
 

DDP-616 6 Channel Digital Dimming Pack • Redesigned and improved 6 channel dimmer • Ideal dimmer for touring and fixed installation • Clear LCD display for all menu settings • Strong 19 inch housing Power supply: AC 220 V - 50/60 Hz, single phase connection Power supply: AC 380 V – 50/60 Hz, 3-phase connection Output power: Max. 10 Amp each channel, Total 60A Output connector: Schuko Circuit breaker: 16 A Control signal: DMX-512, Analogue 0-10 V Protection: Short circuit, temperature, overload Dimensions: 483x380x90 mm (LxWxH) (Rubber feet removed) Dimensions: 483x385x94 mm (LxWxH) (incl. rubber feet) Weight: 12 kg
Weight2.00 kg28.00 kg31.00 kg9.00 kg5.00 kg13.00 kg
DimensionsN/AN/AN/AN/AN/AN/A
Additional information
Weight 2.00 kg
Weight 28.00 kg
Weight 31.00 kg
Weight 9.00 kg
Weight 5.00 kg
Weight 13.00 kg