Content | • Eight and four channel models with 300W and 150W per channel • Minimal footprint and mass arround 200mm depth and 6 Kg • Optional Add-on card to interface with third party alarm systems with GPIO connections • FCM™ Faulty Channel Management system to avoid entire device shutdown • State-of-the-art layout for maximum performance and reliability • Highly oversized thermal dissipation design for maximum reliability • Superb distortion and noise figures • All channels bridgeable by pairs • Selectable gain in four channel groups (26, 32 and 38dB) • Subsonic filter per channel (35Hz user selectable) • Temperature and signal dependant, intelligent cooling system for minimal noise • Optimal heat extraction due to the air tunneled enclosure and insulator-less power device attachment to the heatsink • Direct connector-less output for maximum quality loudspeaker control • High grade engineering inside with the latest SMD technology • Balanced Inputs with 0.1% tolerance resistors for a precise noise rejection • Critical electronic and mechanical parts selection • Innovative protection systems, FCM™ Faulty Channel Management and SSP™ SOA Sentry Protection • Detented and optionally tamper-proof volume potentiometers • Hi efficiency, two steps Class H Audio topology • Protection, Signal and Clip indicators per channel • Power On and Standby general indicators • Extremely compact, fully featured QuantaPulse Power supply • Low current consumption and heat generation allowing less demanding conditions for multiple amplifier installations • Factory preset worldwide mains voltage power supply • Laser cut four milimeters aluminium front panel • Rugged 2U steel chasis
|
OUTPUT POWER |
T-604 |
T-1204 |
T-1208 |
T-2408 |
RMS, 1kHz, 1.0% THD+N |
|
|
|
|
4 ohms |
4x 160 W |
4x 320 W |
8x 150 W |
8x 300 W |
8 ohms |
4x 115 W |
4x 220 W |
8x 100 W |
8x 195 W |
Bridge @ 8ohms |
2x 320 W |
2x 640 W |
4x 300 W |
4x 600 W |
Pink Noise 12dB CF |
|
|
|
|
4 ohms |
4x 210 W |
4x 415 W |
8x 180 W |
8x 370 W |
Frequency Response (power bandwidth ±0.25dB): 20Hz-20kHz
Phase Response (@1W 20Hz-20kHz): ±15deg
Total Harmonic Distortion (20Hz-20kHz): Intermodulation Distortion (SMPTE): Crosstalk (20Hz-20kHz): >70dB
Voltage Gain (selectable): 26/32/38 dB
Sensitivity: T604:1.5/0.8/0.4V - T1204:2.1/1.0/0.5V - T1208:1.4/0.7/0.4V - T2408:2.0/1.0/0.5V
Signal to noise ratio: T604:107dB - T1204:110dB - T1208:107dB - T2408:110dB
Required AC Mains (@8ohms 1/8 rated power): T604:1A - T1204:1.5A - T1208:1.4A - T2408:2.6A
Dimensions (WxHxD): 483x88.9x210 mm - 19x3.5x8.27 inches
Weight (Net): T604/T1204: 5.4Kg - 11.8Lbs T1208/T2408: 6.2Kg-13.5Lbs
Protections: Soft-start, Turn-on Turn-off muting, Over-heating, DC, RF, Short-circuit, Open or mismatched loads, Overloaded power supply, SSP™ and FCM™ |
Model CT475
Product Type Amplifier
Channels 4
Sensitivity 1.4V
Rated Power Output 75W per Channel into 8 ohms
Signal to Noise Ratio (below rated power 20Hz to 20kHz, A-Weighted 110dB
Total Harmonic Distortion (THD) (full rated power, 20Hz - 20kHz)
Intermodular Distortion (from 0dB down to -40dB)
Frequency Response (at 1W into 4/8 ohms) ± 0.5dB
Crosstalk (below rated power 20Hz to 1kHz) > 70dB
Common Mode Rejection (20Hz to 1kHz) > 55dB, typically > 70dB
Dimension (H x W x D) 1.75" x 19" x 14.25“
Weight 10 lbs (4.5 kg)
|
Amplifier Gain 32 dB (Lo-Z), 33 dB (70V), 36 dB (100V) Analog Inputs 4, electronically balanced, Phoenix-type Audio Network No CAN Bus Interface Yes (With Optional RCM-810 Card) Continuous Rated Power (1 kHz, THD 1%) 100v 1000 Watts Continuous Rated Power (1 kHz, THD 1%) 2Ω 1000 Watts Continuous Rated Power (1 kHz, THD 1%) 4Ω 1000 Watts Continuous Rated Power (1 kHz, THD 1%) 70v 1000 Watts Continuous Rated Power (1 kHz, THD 1%) 8Ω 500 Watts Continuous Rated Power (20-20 kHz, THD Continuous Rated Power (20-20 kHz, THD Continuous Rated Power (20-20 kHz, THD Continuous Rated Power (20-20 kHz, THD Cooling Front-to-Rear, continuously variable fans DIM 30 0.02 % Electronics Type Amplifier Frequency Response 15 Hz-30 kHz Input Impedance (Balanced) 20 kΩ Input Sensitivity 0 dBu (.775V)-2 Ω, +3 dBu (1.1V)-4/8 Ω, +6 dBu (1.55) 70V/100V Intermodulation Distortion (SMPTE) 0.05 % Mains Voltage 220 - 240 V, 50 - 60 Hz or 120 V, 50 - 60 Hz, 50 - 60 Hz Network Control (IRIS-Net) Optional Total Harmonic Distortion 0.05 % Variable Load Drive (VLD) Yes Height 2RU 88.1 mm (3.47“) Width 483 mm (19.02“) Depth 421.5 mm (16.59“) Weight Net 11.1 kg (24.47 lbs)
| - 6CH 60W DIGITAL AMPLIFIER
- LIGHT WEIGHT
- 6 BUS BROADCASTING FUNCTION WITH A UTP (CATEGORY 5) CABLE.
- VOLUME AND 5 BAND EQ TUNING FUNCTION BY CHANNEL
- AMP ID AUTO/MANUAL ALLOCATION FUNCTION
- SELF-BROADCASTING FUNCTION USING A LOCAL INPUT
- INTERFACE FUNCTION WITH OTHER EQUIPMENT USING A CONTROL INPUT/OUTPUT CONTACT
- Manufacturer: INTER-M
- Category: AMPLIFIERS
- Use: POWER AMPLIFIERS 100V
- Measurement Unit: Attribute34381
- Warranty Months: 12
- Depth (cm): 38.0
- AC Line Voltage and Frequency Configurations Available: 220-240VAC DC24V
- Height (cm): 8.8
- Weight (Kg): 13.0
- Order Quantity: 1
- Power Output: 60
- Rack Installation Possible: Yes
- Channels: 6
- Power Output W/4Ω: 60
- Frequency Response (at 1W, 4/8Ω) (dB) ±: 80Hz-20KHz
- Catalog: Professional
- Amplifier Type: Power Amplifier
- Load Impedance: Ohm
- Group: Attribute49042, Attribute50583
- Width (cm): 48.2
|
The XM series multi-channel power amplifiers are ideal for theater, hall, and conference room installations. The lineup includes 80W × 4 and 180W × 4 models, meeting the needs of a wide variety of installed systems. The XM amplifiers are a compact 2U size and surprisingly lightweight, making them easy to handle and install. Switching power supplies deliver high output power while minimizing the unit's physical size. The XM series has monitor/remote jacks that allow external devices to be connected for status monitoring or control from a remote location.
Dimensions (W x H x D): 480 x 88 x 412 mm, Weight: 10 kg
Four high-power channels. Switchable stereo, parallel, or bridged operation. Versatile connectivity and high-pass filters for a variety of applications. Distribution drive capability for parallel multi-speakers systems (XM4180).
Monitor/Remote connector for remote monitoring and control.
| Product Features:
- 4 x 75 Watts into 4 Ohms; 4 x 50 Watts into 8 Ohms
- ATR (Accelerated Transient Response) technology for ultimate punch and clarity
- Ultra-light, ultra-low noise and ultra-efficient switch-mode power supply for noise-free audio, superior transient response and low power consumption
- Independent limiters for each channel offer maximum output level with reliable overload protection
- Detented gain controls for precise setting and matching of sensitivity
- Precise Power, Signal and Clip LEDs to monitor performance
- Servo-balanced XLR and 1/4" TRS inputs plus professional speaker connectors
- Independent DC and thermal overload protection on each channel automatically protects amplifier and speakers without shutting down the show
- “Back-to-front" ventilation system including air filter for reliable operation
- “Built-like-a-tank“, impact-resistant and all-steel 1U rackmount chassis
- Minimum depth chassis (10.1" / 257 mm) and ultra-light weight design (8.8 lbs / 4.0 kg) fits into compact, inexpensive effects racks
- High-quality components and exceptionally rugged construction ensure long life
|
Reviews
There are no reviews yet.