Content |
frequency response 53 Hz – 22 kHz
crossover frequency 3 kHz
low-frequency amplifier power 40 watts
high-frequency amplifier power 30 watts
maximum signal-to-noise (dynamic range) > 100 dB (typical A-weighted)
polarity positive signal at + input produce outward LF cone displacement
input impedance 20 k ohms balanced, 10 k ohms unbalanced
input sensitivity 85 mV pink noise input produces 90 dBA output SPL at one meter with volume control at maximum
power factory programmed for either 115V ~50/60 Hz or 230V ~50/60 Hz
protection RF interference, output current limiting, over temperature, turn-on/off transient, subsonic filter, external mains fuse
cabinet vinyl-laminated MDF
size 7.7” x 7” x 10”; 19.5cm x 17.6cm x 25.2cm
weight 11 lbs./unit; 5 kg.
|
PRICE PER UNIT ADAMs A7 & A7X: the evolution of a legend The predecessor to the A7X, the A7, became the most famous of all ADAM monitors in a very short time. Not only has it been reviewed over three dozen times with outstanding results, it has also received numerous awards. The A7 quickly gained mass appeal, praised in many of the worldʼs largest internet forums. Still today, the A7 are the reference monitors in many smaller studios. With the A7X, ADAM Audio proudly presents the evolution of a legend. It takes everything that made the A7 such an outstanding speaker to a new level. Driver technology The first aspect that distinguishes the old from the new model is the X-ART tweeter. The ʽXʼ stands for ʽeXtended frequency responseʼ and thus for one of the features of the Accelerating Ribbon Technology that has been drastically improved: the frequency response. It now extends all the way up to 50kHz. In addition, the X-ART tweeter has a higher efficiency and higher maximum sound pressure levels. The perfect integration with the lower frequencies has been achieved with a newly designed 7” midwoofer. It has been redesigned with a much bigger voice coil (1.5”) and is driven by an amplifier with twice the power compared to its predecessor. This combination produces an amazing sound and pressure levels with an almost distortion-free musical reproduction. Amplifiers / controls Each driver has its own dedicated amplifier. A 50W A/B amp is responsible for the X-ART tweeter, while the midwoofer is being driven by a 100W PWM amp. The front panel includes a power switch and a control for the volume that retains the volume setting independently from the on/off switch. On the rear panel are several additional controls: a gain for the high frequencies (± 4dB) and two shelf filters for high and low frequencies. To ensure greater compatibility, there are both XLR (balanced) and RCA (unbalanced) connectors. Mid-Woofer | | Number | 1 | Basket Ø | 7" (175 mm) | Voice coil Ø | 1.5" (38 mm) | Cone material | Carbon/Rohacell/Glass Fiber | Tweeter | | Number | 1 | Type | X-ART | Diaphragm area | 4 inch² (2420 mm²) | Equiv. Diaphragm Ø | 2" (56 mm) | Velocity transform ratio | 4:1 | Diaphragm weight | 0.17 g | Built-in Amplifiers | | Mid-Woofer | 1 | Type | PWM | Amp. power RMS / music | 100 W / 150 W | Tweeter | 1 | Type | A/B | Amp. power RMS / music | 50 W / 75 W | Control panel | | Input Sensitivity | -∞ to +14 dB | High Shelf EQ > 5 kHz | ±6 dB | Low Shelf EQ | ±6 dB | Tweeter gain | ±4 dB | Input connectors | | Analog | XLR / RCA | General data | | Frequency response | 42 Hz - 50 kHz | THD 90dB/1m > 100 Hz | ≤0.5 % | Long term output | ≥106 dB | Max. peak | ≥114 dB | Crossover frequencies | 2500 Hz | Input impedance | 30 KOhm | Weight | 20.3 lb (9,2 kg) | Magnetically shielded | No | Height x Width x Depth | 13.5" (337 mm) x 8" (201 mm) x 11" (280 mm) | Warranty | 5 Years | Delivery contents | Power cord, Manual |
|
DM-2100: 2.1-ch Speaker System
Features The DM-2100 2.1-ch Speaker System is an affordable way to add accurate reference monitoring with a subwoofer for enhanced bass response. The left and right speakers each offer 15 watts of power, while the 50-watt subwoofer provides a powerful low-end boost. And with 24-bit/96kHz digital inputs, the DM-2100 is perfect for use with Roland/BOSS digital studios and instruments, or with computer systems and more.
- Affordable 2.1-channel monitoring system with 24-bit/96kHz digital inputs
- Powered bass reflex speakers with 15 watts per side and flat frequency response
- Active subwoofer with 50-watt amplifier for increased low end
- Front-mounted controls convenient located on right speaker
- Coaxial and optical digital inputs, plus analog inputs (RCA and 1/4-inch type)
- Sleek black wooden cabinets with magnetic shielding
Rated Output Power50W + 15W + 15WSpeakerSubwoofer: 16cm, Satellite Units: 9.2cmNominal Input LevelLine 1: -10dBu, Line 2: -10dBuInput Impedance18k ohmControlsR Channel: Bass Control Knob, Treble Control Knob, Volume 1 (Digital In/ RCA pin), Volume 2 (1/4” phone), Power Switch, Digital Input Select Switch, Phase SwitchConnectorsR Channel: Line 1 Jack (L, R; RCA pin), Line 2 Jack (L (MONO), R; 1/4” phone), Optical Input Connector, Coaxial Input Connector, Dedicated connector for power control and audio signal, Channel Input Jack (R; RCA pin),
L Channel: Channel Input Jack (L; RCA pin),
Sub Woofer: Dedicated connector for power control and audio signal, Channel Output Jacks (L, R; RCA pin), AC In JackDigital InputSampling Rate 32/44.1/48/96 kHz, D/A Convertor 24 bitsPower SupplyAC117, 230 or 240VAccessoriesSpeaker Cables (RCA pin type), Dedicated Cable for power control and audio signal, Power CableSize and Weight ( Satellite Units )Width130 mm5-1/8 inchesDepth160 mm6-5/16 inchesHeight200 mm7-7/8 inchesWeight
Size and Weight ( SubWoofer )Width240 mm9-1/2 inchesDepth300 mm11-13/16 inchesHeight330 mm13 inches
|
* Active studio monitors with USB audio interface
* 4.25-inch magnetically shielded, inverted cone, copolymer woofer
* 1-inch silk dome high frequency driver
* 2 x 20 watts of internal stereo power
* Two combination mic and instrument/line inputs
* Two 1/8-inch stereo headphone outputs with level controls
* Includes Cakewalk® Sonar LE music production software
* Mic and instrument/line gain control with clip LED
* 16-bit 44.1kHz/48kHz
* Stereo RCA and 1/8-inch aux inputs
* 2-position switch for no-latency direct stereo and mono monitoring
* Mix control to balance computer and audio sources
* USB and speaker cable included
|
PRICE PER UNIT S1X The S1X nearfield monitor delivers high quality sound in a very small cabinet. The S1X has all the critical features of the new SX-Series: the X-ART tweeter in combination with the ADAM designed class A/B amplifier and the HexaCone woofer with optimized magnet/voice-coil systems, driven by premium PWM amplifiers. The smallest reference speaker The combined features of crystal clear resolution, tight and precise low-frequency reproduction and the effortless musical reproduction sets this speaker apart from all conventional designs. The S1X is the first choice in all environments that require high quality within a small space, whether it is a smaller studio, an OB vehicle, or a 5.1 installation. Woofer | | Number | 1 | Basket Ø | 6" (156 mm) | Voice coil Ø | 1.5" (37 mm) | Cone material | HexaCone | Tweeter | | Number | 1 | Type | X-ART | Diaphragm area | 4 inch² (2420 mm²) | Equiv. Diaphragm Ø | 2" (56 mm) | Velocity transform ratio | 4:1 | Diaphragm weight | 0.17 g | Built-in Amplifiers | | Woofer | 1 | Type | PWM | Amp. power RMS / music | 200 W / 280 W | Tweeter | 1 | Type | A/B | Amp. power RMS / music | 50 W / 100 W | Control panel | | Input Sensitivity (coarse) | ±10 dB | High Shelf EQ > 6 kHz | ±6 dB | Low Shelf EQ | ±6 dB | Tweeter gain | ±4 dB | Input connectors | | Analog | XLR | General data | | Panel | Rear | Frequency response | 40 Hz - 50 kHz | THD > 80 Hz | ≤1.5 % | Long term output | ≥103 dB | Max. peak | ≥113 dB | Crossover frequencies | 2200 Hz | Input impedance | 10 KOhm | Weight | 13.2 lb (6 kg) | Magnetically shielded | Optional | Height x Width x Depth | 11.5" (295 mm) x 7" (175 mm) x 10" (260 mm) | Warranty | 5 Years | Delivery contents | Power cord, Manual |
|
MYTHO 6 is a two-way reference studio monitor that features a high quality large metal dome tweeter for the best vocal reproduction and a 6” neodymium vented woofer with a large sized 51 mm voice coil that guarantees very high energy for tight and controlled bass reproduction and perfect thermal stability with minimum power compression.
The magnetic circuit features a special air ventilation to reduce air compression, air noises and minimize distortion in large excursion situations. The MYTHO 6 is equipped with two separate amplifiers: 200 W for the low frequencies and 100 W for the high. The design is a classic AB circuit, unparalleled for low distortion and natural sound. The signal processing is executed from a dedicated high quality DSP processing. It features a solid aluminium cabinet internally braced and reinforced to improve low frequencies behaviour and reduce resonances.
Acoustical Specifications |
---|
Frequency Response -3 dB: | 40 Hz | ÷ 20 kHz | Max SPL: | 114 dB | | Horizontal coverage angle: | 110° | | Vertical coverage angle: | 70° | | Compression Driver: | 1" neo, metal dome | | Woofer: | 6.5" neo, ICC technology | |
INPUT/OUTPUT SECTION |
---|
Input connectors: | combo XLR/Jack | | Input sensitivity: | -6/+6 dBu | |
PROCESSOR SECTION |
---|
Crossover frequencies: | 1900 Hz | | Protections: | thermal, excurs., rms | | Limiter: | soft limiter | | Controls: | bass tilt, roll-off, treeble tilt, desktop, DSP controlled | |
AMPLIFIER SPECIFICATIONS |
---|
High frequencies: | 100 Watts | | Low frequencies: | 200 Watts | | Cooling: | convection | | Connections: | vde | |
CABINET |
---|
Cabinet Material: | die cast aluminum | | Hardware: | orientation adjustable stand | |
PHYSICAL SPECIFICATIONS |
---|
Height: | 370/14.5 mm/inch | | Width: | 265/10.4 mm/inch | | Depth: | 250/9.8 mm/inch | | Net Weight: | 10.5/23 Kg/Lbs |
|
Reviews
There are no reviews yet.