Content | • Solid housing
• RIAA Equalization
• High quality components
The PRE-101 is a phono pre-amp with RIAA equalization. The tiny signal of magnetic pick-ups is amplified to fit the line-level inputs of mixers or USB sound-cards.
Specifications Frequency Response: 20Hz-20KHz RIAA
Inputs: RCA
Outputs: RCA
Input sensitivity: 3mV for 1000 mV output
Input Impedance: 47 kOhm
Nominal Output Voltage: 0 dBV
Max Output voltage: +16 dBu
Output impedance: 100-600 Ohms
Power supply: 18V AC (adapter included)
Dimensions: 40 x 113 x 80 mm (HxWxD)
Weight: 0,35 Kg |
The AD2022 is Avalon's fourth generation of fully discrete, symmetrical Pure Class A microphone preamplifiers. The dual mono AD2022 includes the original sonic capabilities and transparency of the M2, M22 and M5 preamplifiers plus several additional features, including selectable microphone source loading for optimized cable/mic matching, improved high-voltage Class A regulated power supplies, two high Z instrument inputs, variable-passive high pass filter, teflon/ silver wiring and doubled plated circuit boards for superior low level signal transfer. AD2022 FEATURES Symmetrical Pure Class A design, two channels Microphone and hi-Z instrument inputs Gain switched 4dB steps plus +/- 3dB fine output trim Selectable microphone input impedance matching Low noise -126dB EIN Ultra high quality, low-ratio, balanced input transformer Balanced, high-current Class A output to +36dB Large illuminated analog VU meters and twin peak LED's Regulated phantom power supply +48v Input polarity phase reverse High headroom +36dB input before overload Input -20dB pad for high level signals Sealed silver relays for all signal routing External AC 150w toroidal power chassis Fully discrete Class A regulated audio power supplies Deep, musical sound-stage, transparent amplification
MICROPHONE INPUT The AD2022 incorporates the most advanced high-performance microphone transformer available. Split low-ratio primary windings are carefully combined within a custom mu-metal core for extended smooth frequency response and very low distortion. Sealer silver relays are used for minimal signal invasion. The input signal selector, high pass filter, polarity-phase reverse, +48v power and the 20dB input attenuator all utilize local sealed relay operation. A variable passive high pass filter provides a minimum phase shift design while eliminating low frequency rumble, wind noise and mechanical vibration at sub sonic frequencies.
SYMMETRICAL PURE CLASS A DESIGN Two 100% discrete, high-voltage, symmetrical Pure Class A signal amplifiers are utilized per channel. The first operates in a cascaded-cascode FET configuration while the second stage amplifier is fully bipolar. The twin amplifiers share the total available gain requirement. This shared architecture increases the high level headroom capability, improves transient response and doubles the internal bandwidth of the ultra-high performance pure Class A signal amplifiers. OUTPUT and METERING High-current DC coupled, Class A discrete amplifiers are utilized for the output drive interface with +36dB capability into all known loads. Two large, high-quality analog VU meters indicate accurate signal readings while bi-color LED's offers peak indication at 0dB and +20dB.
AD2022 PREAMPLIFIER SPECIFICATIONS Circuit Topology: Twin cascode FET and bipolar low level signal amplifiers, high-voltage, 100% discrete, symmetrical Pure Class A Input Type and Load: Transformer balanced low-ratio, 50, 150, 600 and 1k5 ohm input load selection Maximum Mic Level: +36dB balanced XLR pin 2 hot (with -20dB passive attenuator) Maximum Instrument Level +18dB at 100k ohms instrument input level, standard mono 1/4 inch jack Input Attenuator: -20dB resistive pre transformer primary, sealed silver relay Phantom Power: +48v regulated 50mA capability, sealed silver relay High Pass Filter: Passive, variable from 30Hz to 185Hz @ 6dB per octave, sealed silver relay. Polarity Reverse: Sealed silver relay on microphone input Gain Range Input: +20dB to +64dB in 4dB steps Gain Output Range: +/- 3dB variable conductive plastic potentiometer Maximum Output Level: +36dB balanced 600 ohms, DC coupled, discrete symmetrical Pure Class A Output Type: XLR connector, pin 2 hot Noise EIN Unweighted: -126dB 150 ohm Noise 20kHz Unweighted: -102dB Distortion THD, IMD: 0.05% nominal Frequency Response -3dB: 1Hz to 120kHz transformer limit System Bandwidth: DC to 1MHz Output Meter: High quality, illuminated analog VU meter 0dB = +4dB. Peak Meter: Bi-color LED's 0dB and +20dB peak detection circuit. AC power supply B2T: External toroidal 100V to 240V, 50-60Hz selectable, 150 watts maximum. Cables: 90V ac, 4 pin male power input connector, B2T required, internal DC regulation Dimensions: 19 x 12 x 3.5 in (482 x 305 x 89mm) Weight: 15lbs (6.8kg) Dimensions - Shipping Carton: 24 x 21.5 x 7.5 in (610 x 546 x 190mm) Weight - Packed: 25lbs (11.4kg) |
EWI PDI-100 PARA ACOUSTIC DI Box
This is a medium grade professional application Para Acoustic Active DI, which will work well on instruments with passive pickups or active pickups.
The construction is reasonably rugged and the components are well suited for the application yielding results that are typically acceptable for all but the most discerning artists.
The on-board tone and volume controls give the operator a lot of choices in shaping their sound prior to sending the signal to the mix console. This allows an artist to use this device in-place of or in addition to a traditional stage amp for their instrument. This is an excellent choice for IEM bands, or bands that like to keep their stage volume low.
This item is typically used to split the instrument signal going to a stage amp so a feed can be sent also to the mix board, or be used as a stand-alone instrument pre-amp. It is equipped with a ¼” jack for input, a 1/4" jack for output to a stage amp, one XLR jack for the send to the board and a TRS jack for inserting an FX device.Since this is an active D.I. box, it needs to be powered which can be done either with Phantom Power from the mix board, or with the supplied internal 9v battery. The battery is fairly easy to change by removing one screw in the bottom of the case.
|
-
- Ultra-high quality 8-channel A/D and D/A interface for virtually any digital recording/mixing environment
- 8 state-of-the-art MIDAS designed Mic Preamplifiers
- Phantom power on all microphone inputs
- Reference-class Cirrus Logic 24-bit converters for ultimate signal integrity
- Processes 48 and 44.1 kHz sample rates
- External sample rate synchronization via word clock or ADAT input
- Optical ADAT in/out interface for ultimate compatibility
- All mic/line inputs routed to the ADAT output
- ADAT input routed to all Line outputs
- “Planet Earth" switching power supply for maximum flexibility (100 - 240 V~), noise-free audio, superior transient response plus low power consumption for energy saving
- High-quality components and exceptionally rugged construction ensure long life
- Conceived and designed by BEHRINGER Germany
|
The PreSonus HP60 is the most flexible and advanced headphone amplifier system available for professional and project recording studios as well as live sound in-ear monitoring systems. Loaded with six independent,
loud and clear headphone amplifiers, the HP60 features dual stereo inputs as well as external input, for each
channel allowing you to mix between three stereo audio streams (mix A, mix B, and external input). Stereo output is also available on each channel to send line level headphone channel mixes to additional headphone amplifiers or monitor systems. Each channel features headphone level, mix control between A and B inputs, external input volume, mute and mono. The HP60 also features talkback via external XLR microphone input. Common set up of the HP60 in a recording session is to send the main control room mix to input A. Send the click track to input B. Send the each band member direct recording input to each channelʼs external input (more me). This will allow each band member to create a mix between the main mix, the click track and themselves. The HP60 is the ultimate headphone amplification system delivering loud and clear headphone mixes for real-world recording situations.
Features:
-Six independent ultra low noise, high output headphone amplifiers (150 mW per channel)
-Two sets of stereo inputs (A and B) with balanced TRS connectors
-Stereo external input point on each channel for "more me” with trim control
-Mix control between inputs A and B
-Talkback with external XLR microphone with control
-Direct stereo line output on each channel
Input A
|
(2) ¼” TRS balanced 10 Ohms
|
Input B
|
(2) ¼” TRS balanced 10 Ohms
|
External input
|
TRS stereo unbalanced 10 Ohms
|
Headphone amplifier output power
|
150 mW RMS (60 Ohms) per channel
|
Audio outputs
|
¼” TRS stereo unbalanced per channel
|
Master controls
|
Talk button, Talkback volume, Input A, Input B
|
Channel controls
|
Headphone level, Mix A/B control, External input level, Mono, Mute
|
External talkback
|
XLR with TS external control jack
|
Power
|
IEC 110V-240V internal switching
|
|
- 1 microphone, XLR (bal.) or 6.3 mm jack (unbal.)
- Gain control, 10 steps (6-50 dB)
- Phantom power can be switched on
- Clip LED
- 1 line output, XLR (bal.) or 6.3 mm (unbal.)
- Operation via supplied power unit
Power supply: | 12 V DC, 150 mA | Input impedance: | 10 kohms bal./unbal. | Max. input level: | +4 dB bal./+10 dB unbal. | Gain: | 50 dB XLR/44 dB jack | T.H.D.: | 0.01 % | Frequency range: | 25 Hz - 16 kHz | S/N ratio: | >75 dB | Dimensions: | 143 x 93 x 45 mm | Weight: | 350 g |
|
Reviews
There are no reviews yet.