Content |
D4175_MANUAL_GB_V1.pdf
HP-500
• Full protection circuits • Efficient forced air cooling • Stereo & Bridge mode
The DAP HP Series power amplifiers are the solution when true quality is needed in an affordable price range. The HP Series are 5 models representing output powers from stereo 200W until 1400W. All including the best protection circuits and built in a strong solid housing to achieve many years of reliable power. They are the best mobile choice for musicians, DJs, and entertainers but also perfect for installations in discos, pubs or any kind of public areas.
The HP Series power amplifiers by DAP Audio are the obvious choice for musicians, DJs, and entertainers and also perfectly suited for permanent installation in discos, pubs or public areas. The DAP Audio HP Series includes five power-amp models with outputs ranging from 200W to 1400W RMS stereo at 4 Ohms. The solid yet fashionable housings all hold forced air-cooling systems and the best protection circuits, ensuring many years of reliable amplification.
The HP-500 and HP-900 are ideal for pubs, bars, and parties. These class AB power amps deliver enough output to make everyone sing along and dance to their favorite tunes.
These amplifiers truly are the best choice wherever quality and reliability at affordable prices are required.
specifications
Output Power Stereo 2Ohm: Not Allowed Stereo 4Ohm: 2x 200 Watt RMS Stereo 8Ohm: 2x 150 Watt RMS Bridge 2Ohm: Not Allowed Bridge 4Ohm: Not Allowed Bridge 8Ohm: 1x400 Watt RMS Frequency Response: 10Hz - 20KHz, +/-1dB THD: 100dB A-weighted Crosstalk: >75dB Damping Factor: >100 8 OHM Gain: 32dB Input Sensitivity: 0,775V (+/-1dBv) Input Impedance: 20kOhm balanced, 10kOhm unbalanced Output Mode: Stereo / Parallel / Bridge Amp Technology: Class AB Protection: Clip Limiter (Fixed) Short Circuit Overheat Overload DC Voltage Cooling: Forced-air by axial fan Airflow: Front to side Input Connectors: 3-pin XLR Output Connectors: Speakon Power Connector: IEC Input Voltage: 210~240VAC, 50/60Hz Dimensions: 483 x 310 x 88mm Weight: 8Kg |
VLP Series Powere Amplifier
Output Power: 300W RMS Per Channel @ 4 Ohms, 1kHz, 0.1% THD 200W RMS Per Channel @ 8 Ohms, 1kHz, 0.1% THD (Bridge Mode, Mono) 600W RMS @ 8 Ohms, 1K Hz, 1% THD
Total Harmonic Distortion: Less Than 0.1% (20Hz - 20kHz @ 8 Ohms)
Frequency Response: (+/-01db, @rated output Power, 8 Ohms): 20Hz - 20K Hz
Slew Rate: 15V Per usec
Damping Factor @ 8 Ohm: 300
Impedance: 20 Ohms balanced / 10 Ohms unbalanced
Cooling System: 2 indivdual fans
Special Features: High/Low Pass Filter / Input Sensitivity Selector / Ground Lift Limiter
Dimensions (LxWxH): 14" x 19" x 3.5" / 360 x 482 x 88mm 2-rack mount spaces
Weight: 33 lbs. / 15 Kgs.
Special Features: High/Low Pass Filter; Input Sensitivity Selector; Ground Lift; Limiter
| Phonic's MAX 1500 Power Amplifier provides 900 Watts of power at 8 ohms (bridge mono) or 450 Watts at 4 ohms (stereo) - ideal for clubs, churches, auditoriums and more. Input to the MAX 1500 amp is achieved via XLR or phone jack, and output is achieved either through Speakon-type connectors or traditional binding posts. The MAX 1500 features ground switches, user defeatable clip limiters, selectable high pass filters, and the option to choose between stereo, parallel and bridge operating modes, making this amplifier ideal for real world application.
- Output power: 450W @ 4 Ohms stereo, 280W @ 8 Ohms stereo
- High-current toroidal transformers for greater power and low noise
- Independent user-defeatable peak limiters reduce distortion
- Selectable High-Pass filter at 30Hz or 50Hz
- XLR and 1/4' TRS input jacks
- Binding post and Speakon?-type outputs
- Front mounted gain controls for easy access
- Signal and Peak LED indicators to monitor performance
- Short circuit, thermal, subsonic, RF protection, output DC offset
- Power on/off muting
|
XB Series - Intelligent Power
Power Without Compromises. The XB is designed for paging, music and alarm signals. Versatile, dynamic and extremely rugged according to IEC286-3. For the highest requirements in safety and quality. Sequential power on, alive contacts and incorporated ground fault detection- the XB is the solution under all conditions. Without the need for additional equipment. For uninterrupted and troublefree operation.
High Tech SMT Design Protection Circuits: DC, LF, HF, Thermal, Short Circuit, Current Limiter, 3 ms Muting Delay PHOENIX / Speakon LED Indicators for POWER, SIGNAL, CLIP, PROTECT Temperature controlled, variable speed low noise fans Volume Controls at the back Stereo / Bridged / Parallel Mode Softstart Sequential Remote Power On Alive Contact Ground Lift 3 Years Warranty
TECHNICAL DATA: XB 800: 2x 400 W @ 4 Ohm Class: AB Frequency Response: 20 Hz - 20 kHz (0 / -0.3 dB) THD: < 0.025% Signal-to-Noise Ratio: < 103 dB Channel Seperation: > 85 dB Input Sensitivity: +6 dBu Input Clipping: 22 dBu Input Impedance: 20 kOhm Damping Factor: 500 @ 4 Ohm Cooling: 2x fan (temp. reg. variable speed) Weight: 13 kg/(29 lbs) Dimensions: 2 RU / 483 x 88 x 382 mm (19" x 3.5" x 15“)
|
Power Output Level R-300 PLUS
STEREO
8ohm(T.H.D 0.05%) 170W+170W
4ohm(T.H.D 0.05%) 250W+250W
BRIDGED MONO
8ohm(T.H.D 0.05%) 460W
8ohm(T.H.D 0.5%) 500W
Frequency Response 20Hz- 20kHz, ±0.5dB
Convection Cooled
SoftStart Protection System
Balanced 10kΩ@0.775V Inputs
|
These amplifiers offer high, stable power output and a high efficiency factor on the high performance level and are therefore the ideal choice for driving a multitude of mobile and club systems. SL series power amplifiers are equipped with a comprehensive protection package and dynamic limiters.
The integrated, switchable Low-Pass Notch filter (a typical DYNACORD special feature) corrects the frequency response and optimizes the transient behaviour of loudspeakers.
Maximum Midband Output Power, THD = 1%, 1 kHz, Dual Channel 2 Ω - 650 W, 4 Ω - 450 W, 8 Ω - 270 W Maximum Single Channel Output Power, Dynamic-Headroom, IHF-A 2 Ω - 1150 W, 4 Ω - 660 W, 8 Ω - 350 W Maximum Bridged Output Power, THD = 1%, 1 kHz 4 Ω - 1300 W, 8 Ω - 900 W Input Sensitivity, rated power @ 8 Ω, 1 kHz + 2,2 dBu (1,0 Vrms) Maximum Input Level +21 dBu (8.69 Vrms) Voltage Gain, ref. 1 kHz 32.0 dB Frequency Response, ref. 1 kHz 10 Hz...40 kHz (±1 dB) Output Stage Topology Class AB Dimensions (W x H x D), mm 483 x 88.1 x 421.5 Weight 12.6 kg (27.8 lbs)
|
Reviews
There are no reviews yet.