Content |
D4178_MANUAL_GB_V1.pdf
DAP HP-2100
• Full protection circuits • Efficient forced air cooling • Stereo & Bridge mode
The DAP HP Series power amplifiers are the solution when true quality is needed in an affordable price range. The HP Series are 5 models representing output powers from stereo 200W until 1400W. All including the best protection circuits and built in a strong solid housing to achieve many years of reliable power. They are the best mobile choice for musicians, DJs, and entertainers but also perfect for installations in discos, pubs or any kind of public areas.
The HP Series power amplifiers by DAP Audio are the obvious choice for musicians, DJs, and entertainers and also perfectly suited for permanent installation in discos, pubs or public areas. The DAP Audio HP Series includes five power-amp models with outputs ranging from 200W to 1400W RMS stereo at 4 Ohms. The solid yet fashionable housings all hold forced air-cooling systems and the best protection circuits, ensuring many years of reliable amplification.
The HP-1500 and HP-2100 are the mid-range of the DAP Audio HP power amplifier series and are ideal for medium-sized events and clubs. Both with sufficient output to provide the audience with powerful basses and impressive highs.
These amplifiers truly are the best choice wherever quality and reliability at affordable prices are required.
SPECIFICATIONS
Output Power Stereo 2Ohm: Not Allowed Stereo 4Ohm: 2x 1000 Watt RMS Stereo 8Ohm: 2x 700 Watt RMS Bridge 2Ohm: Not Allowed Bridge 4Ohm: Not Allowed Bridge 8Ohm: 1x2000 Watt RMS Frequency Response: 10Hz - 20KHz, +/-1dB THD: 100dB A-weighted Crosstalk: >75dB Damping Factor: >250 8 OHM Gain: 34.5dB Input Sensitivity: 0,85V (+/-1dBv) Input Impedance: 20kOhm balanced, 10kOhm unbalanced Output Mode: Stereo / Parallel / Bridge Amp Technology: Class H Protection: Clip Limiter (Fixed) Short Circuit Overheat Overload DC Voltage Cooling: Forced-air by axial fan Airflow: Front to side Input Connectors: 3-pin XLR Output Connectors: Speakon Power Connector: IEC Input Voltage: 210~240VAC, 50/60Hz Dimensions: 483 x 360 x 88mm Weight: 14Kg |
Number of Channels: 2
Output Power: (per channel)
8 ohms 1000W
4 ohms 1850W
2 ohms N/A
Output Power: (bridged)
8 ohms 3700W
4 ohms N/A
THD%: (@1dB below max output)
@ 1kHz |
The E Series is a range of lightweight, high-power switch mode amplifiers designed to the highest standards of reliability and sound quality. Developed for the touring market, E Series retain the sonic integrity of the benchmark MC and T Series amplifiers, without the physical weight. The switch mode power supply is capable of delivering high peaks without any perceptible bass 'sag' at very low distortion and is kept within its safe operating area by the new, sophisticated MC² Audio 'intelligent' limiter. The E15, E25, E45 and E4-75 feature MC² Audioʼs proprietary current driven output stages for ultra-high definition sound, delivered over the entire audio bandwidth. The E90 and the E100 are Class D amplifiers designed to meet the demands for higher power with increased efficiency whilst still maintaining the renowned MC² Audio sonic qualities and unsurpassed reliability. All MC² Audio products are covered by a 5 year warranty. Number of Channels: 2 Frequency Response: 20Hz to 20kHz (+/- 0.3dB) Output Power: (per channel) 8 ohms 1250W 4 ohms 2500W 2 ohms 4200W Output Power: (bridged) 8 ohms 5000W 4 ohms 8400W THD%: (@1dB below max output) @ 1kHz 20Hz to 20kHz Gain / Sensitivity: Gain 26/32/33dB Sensitivity (for max power) dBu +15.7/9.7/5.7 (4.7/2.4/1.5V) Power Consumption: Nominal @ 240v into 4 ohms 4.5A Nominal @ 120v into 4 ohms 9.0A Dimensions: (2U) (mm) Amplifier 88(h) x 482(w) x 428(d) Single Box (UK shipping) 230 x 580 x 560 Double Box (outside UK) 250 x 610 x 600 Weight: Amplifier 11.4kg Boxed (shipping weight) 13.4kg User's Manual
|
Power supply
- Powersoft legendary universal switch-mode power supply up to 400VAC tolerant with Power Factor Correction
- Patented output filter with ripple cancellation network
- Low Inrush Limiting reduces AC inrush current, removing the need for expensive power sequencers
- Detachable AC mains cable with IEC C19/22.2 (16A for EU, 20 A for USA) socket
Protections
Fully protected circuit design with:
- Ac protection: shut down power supply when AC mains voltage is outside the operating range
- Clip limiter: prevents severely clipped waveforms from reaching loudspeakers, while still maintaining full peak power output
- DC protection: protects against infrasonic signal at the outputs
- VHF protections: protects the loudspeakers against non-audible, strong, non-musical high-frequency signals
- Short circuit protection: protects the amplifier from short circuit or other stressful events for the output circuits with automatic protection reset
- Long term limiter: protects the loudspeaker against steady long term RMS (non-audio) signals, by reducing maximum output
- Thermal protection: output stages operating temperature up to 80 °C (176 °F)
- Temperature controlled continuous variable speed fan, front to back airflow
- Temperature forecast with LCD traced historical behavior
General
- Fixed frequency switchmode output stage for high grade sound accuracy
- Compact size – all models only 1 RU for reduced rack cost and space
- Light weight – for easier racking and shipping: 7 kg (15.4 lbs)
- Standard Phoenix connectors: analog audio outputs, aux supply, alarms and GPIO
- Remotely switchable double input (main and aux) per channel
Loudspeaker system configuration
- Direct drive either low impedance loads or 70V / 100V Hi-Z distributed lines
- Switchable 35Hz / 70Hz high pass filter per channel
- Mixed configuration with Lo-Z/Hi-Z systems possible
- Bridged mode low impedance per channel pair
Alarms and GPI/O
- NC/NO contacts per channel for alarm notifications
- Remote ON/OFF switch
- Remote VCA control per channel
Digital Signal Processing
- TI C6000 DSP platform
- AD/DA converter: dual 24bit @ 48 kHz Tandem® architecture
- Input/output independent equalizers per channel providing PEQ, raised cosine, shelving IIR filters as well as custom output FIR filters
- Delay up to 100 ms for time alignment
- Active DampingControl™ for cable compensation
- Peak, RMS voltage, RMS current, TruePower™ limiters
Remote Control & Monitoring
Via software:
- Control and diagnostics monitoring via ArmoníaPlus
- Dedicated WebApp
Via Hardware:
- Attenuation (from 0dB to 26dB)
- High-pass filters (35Hz, 70Hz)
- Lo-Z/Hi-Z/70V/100V output selection
- Adjustable gain (from 26dB to 35 dB)
General |
Output power per Channel |
Output power per Channel |
1000 W @ 2 Ω |
800 W @ 4 Ω |
800 W @ 8 Ω |
Bridge mode |
|
2000 W @ 4 Ω |
1600 W @ 8 Ω |
Max output voltage / current |
Max unclipped output voltage@8 Ω |
|
|
115 Vpeak |
Current |
|
|
45 Apeak |
AC main power |
Power supply |
Universal, regulated switch mode with PFC (Power Factor Correction) |
Nominal power requirement |
|
|
100-240 V ±10%, 50-60 Hz |
Operating voltage |
|
|
90 V – 264 V |
Power consumption / current draw |
Idle |
|
115 V: 23 W – 0.34 A |
230 V: 23.3 W – 0.21 A |
1/8 of max output power @ 4 Ω |
|
115 V: 267 W – 2.5 A |
230 V: 274 W – 1.5 A |
THERMAL |
Operating temperature range |
|
|
0° – 45° C – 32° – 113° F |
Thermal dissipation* |
Idle |
|
115 V: 78 BTU/h |
230 V: 79 BTU/h |
1/8 of max output power @ 4 Ω |
|
115 V: 229 BTU/h |
230 V: 251 BTU/h |
|
XR Series - Intelligent Power New Horizons.
A lightweight with enormous power output. Combined with digital signal processing. That's what we call flexibility! Locally controlled or completely networked. No matter what the requirements are. The integrated powerful digital signal processor (DSP) and controller allows for a troublefree and easy adjustment to any acoustical environment. Wear-free digital potentiometers, sequential remote power on, alive contacts for easy supervision, computer controlled monitoring - its enless list of useful feature make it the right choice for any installation. XR - the new definition of Intelligent Power
High Tech SMT Design Digital Signal Processor Excellent sound and superior impulse response Protection Circuits: DC, LF, HF, Thermal, Short Circuit, Current Limiter, 3 ms Muting Delay PHOENIX / Speakon High-End Switched Power Supply with Power Factor Correction (not XR4000) LED Indicators for SIGNAL, CLIP, PROTECT, POWER Temperature controlled, variable speed low noise fans Digital wear-free Volume Controls (can be operated manually) Stereo / Bridged / Parallel Mode Softstart Sequential Remote Power On Alive Contact Paging Input Monitor Output SXL Dataport Perfect Weight-to-Power ratio 3 Years Warranty
Technical Data: XR 4000: 2x 2800 W @ 2 Ohm 2x 2070 W @ 4 Ohm Class: H Frequency Response:20 Hz - 20 kHz (0 / -0.3 dB) THD: < 0.02% Signal-to-Noise Ratio: < -106 dB Channel Seperation: > 85 dB Input Sensitivity: +6 dBu Input Clipping: 22 dBu Input Impedance: 20 kOhm Damping Factor: 750 to 1200 @ 4 Ohm Cooling: 4 Fans (temp. reg. variable speed) Weight: 9 kg Dimensions: 2 RU / 483 x 88 x 454 mm(19" x 3.5" x 17.9“)
|
- 2900W RMS x 1 at 2 ohms
- 1780W RMS x 1 at 4 ohms
- 975W RMS x 1 at 8 ohms
- 2525W RMS x 2 at 2 ohms
- 1510W RMS x 2 at 4 ohms
- 890W RMS x 2 at 8 ohms
- 2 channel independent, fourth-order Linkwitz-Riley crossovers
- DDT protection
- Revolutionary IPR class D topology
- Detented input controls
- Combination XLR 1/4 inputs
- 4 pole twist lock output connectors
- Ultra-light weight
- Individual signal pass 1/4" jacks on each channel
- LED illuminated
- Standby, LED power present indication
- Weight Unpacked: 6.2 kg
- Weight Packed: 7.9 kg
- Width Packed: 53.34 cm
- Height Packed: 53.848 cm
- Depth Packed: 15.24 cm
|
Reviews
There are no reviews yet.