| Content |
D4179_MANUAL_GB_V1.pdf
HP-3000
• Full protection circuits
• Efficient forced air cooling
• Stereo & Bridge mode
The DAP HP Series power amplifiers are the solution when true quality is needed in an affordable price range. The HP Series are 5 models representing output powers from stereo 200W until 1400W. All including the best protection circuits and built in a strong solid housing to achieve many years of reliable power. They are the best mobile choice for musicians, DJs, and entertainers but also perfect for installations in discos, pubs or any kind of public areas.
The HP Series power amplifiers by DAP Audio are the obvious choice for musicians, DJs, and entertainers and also perfectly suited for permanent installation in discos, pubs or public areas.
The DAP Audio HP Series includes five power-amp models with outputs ranging from 200W to 1400W RMS stereo at 4 Ohms. The solid yet fashionable housings all hold forced air-cooling systems and the best protection circuits, ensuring many years of reliable amplification.
The HP-3000 represents the true heavy-duty machine in this series. This 3-step H-Class power amp is designed for use in larger venues and clubs. It delivers enough power to seriously shake the foundations and make your audiences dance and party until dawn.
These amplifiers truly are the best choice wherever quality and reliability at affordable prices are required.
SPECIFICATIONS
Output Power
Stereo 2Ohm: Not Allowed
Stereo 4Ohm: 2x 1400 Watt RMS
Stereo 8Ohm: 2x 1200 Watt RMS
Bridge 2Ohm: Not Allowed
Bridge 4Ohm: Not Allowed
Bridge 8Ohm: 1x2800 Watt RMS
Frequency Response: 10Hz - 20KHz, +/-1dB
THD: 100dB A-weighted
Crosstalk: >75dB
Damping Factor: >100 8 OHM
Gain: 36dB
Input Sensitivity: 0,775V (+/-1dBv)
Input Impedance: 20kOhm balanced, 10kOhm unbalanced
Output Mode: Stereo / Parallel / Bridge
Amp Technology: Class H 3-STEP
Protection: Clip Limiter (Fixed)
Short Circuit
Overheat
Overload
DC Voltage
Cooling: Forced-air by axial fan
Airflow: Front to side
Input Connectors: 3-pin XLR
Output Connectors: Speakon
Power Connector: IEC
Input Voltage: 210~240VAC, 50/60Hz
Dimensions: 483 x 400 x 88mm
Weight: 17Kg |
Τελικός Ενισχυτής Switching, ισχύος 2X3000W/4Ω, bridged 6000W/4Ω, με ενσωματωμένο επεξεργαστή DSP με έτοιμα preset για διάφορα ηχεία, EQ, limiting, compression, delay, crossover frequencies και subharmonic synthesizer για κάθε κανάλι. Είσοδοι τύπου Phoenix & HD-15, έξοδοι τύπου Barrier Strip, διαχείριση μέσω με Η/Υ (USB) συμβατότητα με HiQnet. Κατάλληλος για κινηματογραφική χρήση, 15 έτοιμα εργοστασιακά preset για κινηματογραφικά ηχεία JBL. Βάρος 10,6 Kg. |
Engineered from the ground up for unmatched quality and performance,
the Crown? DSi Series of power amplifiers offers three models of 500W,
800W, and 1200W per channel at 4 ohms. Onboard digital signal processing
includes crossovers, EQ filters, delay and output limiting. Rear panel HD-15
connector provides easy input/output connectivity between DSi amplifiers
and the new DSi-8M System Monitor.
The intuitive front panel LCD screen guides installers through a setup process?
featuring presets for the industry-standard JBL cinema loudspeaker systems?
to make configuration quick and easy.
At the touch of a button, Crown?s DSi cinema amplifiers deliver perfectly matched
performance with each award-winning JBL ScreenArray? system, making this the
ultimate cinema solution.
Features :
Includes three models of 500W, 800W, and 1200W per channel at 4 ohms
Automatic presets for popular JBL cinema speaker systems for quick, easy
configuration
Intuitive front-panel LCD screen guides installers through setup
Onboard digital signal processing includes crossovers, EQ filters, delay, and
output limiting
Computer connectivity via USB allows fast setup and configuration with HiQnet?
System Architect? software
Rear-panel HD-15 connector provides easy input/output connectivity between DSi
amplifiers and new DSi-8M System Monitor
Switch-mode universal power supply
All products fill 2U rack spaces and weigh under 19 pounds
Barrier strip outputs, removable Phoenix-style input
Three-Year, No-Fault, Fully Transferable Warranty completely protects your investment
and guarantees its specifications
The Crown? DSi 1000 power amplifi er shall be a solid-state two-channel model
with a switch-mode universal power supply. A rear-panel HD-15 connector shall
provide input/output connectivity between the DSi amplifi er and the DSi-8M
System Monitor.
The outputs shall be usable as stereo or bridged-mono modes of operation.
The bridged-mono mode shall bridge the outputs to provide increased output
voltage.
Front panel controls and indicators shall include the following:
Level: Detented rotary level control, one per channel.
Power Switch: On/off switch applies AC power to the amplifi er.
Sel/Prev/Next Buttons: Three buttons near the LCD screen shall be used to
access menu items.
LCD Screen: Backlit liquid crystal display shows speaker presets and signal
processing.
Signal Indicator: Green LED, one per channel, fl ashes when a very low-level
signal is present at input.
?10 Indicator: Green LED flashes when output signal exceeds ?10 dB below
clip.
?20 Indicator: Green LED flashes when output signal level exceeds ?20 dB
below clip.
Ready Indicator: Green LED, one per channel, illuminates when the amplifi er is
ready to produce audio.
Clip Indicator: Red LED, one per channel, turns on at the threshold of audible
distortion.
Temp/Fault Indicator: Red LED, one per channel, illuminates under Fault or
excessive temperature conditions.
Power Indicator: Blue LED illuminates when the amplifi er has been turned on
and has power.
Rear panel controls and connectors shall include the following:
AC Line Connector: NEMA 5-15P (15A).
Input Connector: Two 3-pin removable Phoenix-type connectors each accept a
balanced line-level input signal.
Output Connectors: 4-position barrier strip with connectors for dual louspeakers
or bridge-mono loudspeaker.
HiQnet USB Connector: Type B, connects to a HiQnet network.
HD-15 Connector: For cinema I/O compatibility with DSi-8M System Monitor.
The amplifi er shall have the following specifi cations:
Output Power: 2 ohm Stereo (per channel): 700W with 1% THD, 4 ohm Stereo
(per channel): 500W with 0.5% THD, 8 ohm Stereo (per channel) 275W with
0.5% THD, 4 ohm Bridge-Mono: 1,400W with 1% THD, 8 ohm Bridge-Mono:
1,000W with 0.5% THD.
Voltage Gain at 1kHz, 8 ohm rated output: 26 dB.
Frequency Response: +0/?1 dB from 20 Hz to 20 kHz at 1 watt into 4 ohms.
Load Impedance: Safe with all types of loads. Rated for 2 to 8 ohms in Stereo
mode, 4 to 16 ohms in Bridge-Mono mode.
Sensitivity at 8 ohm rated output: 2.35V.
Sensitivity at 4 ohm rated output: 2.24V.
Sensitivity at 2 ohm rated output: 1.88V.
Signal to Noise Ratio (below rated 8-ohm power at 1 kHz): 105 dB
(A weighted).
Damping Factor: Better than 500 from 20 Hz to 500 Hz.
Crosstalk: > 70 dB below rated power, 20 Hz to 1 kHz.
Input Stage: Input is electronically balanced and employs precision 1% resistors.
Input Impedance (nominal): 20 k ohms, balanced;10 k ohms, unbalanced.
Maximum Input Signal: +22 dBu typical.
AC Line Voltage and Frequency Confi gurations Available: 100V, 120V, 220-240V,
50/60 Hz.
AC Line Current: 6.5A.
At Idle: Draws no more than 90 watts.
Operating Temperature: 0° C to 40° C at 95% relative humidity (non-condensing).
The DSP section shall have the following specifi cations:
EQ: 6 parametric fi lters per channel with adjustable Q, boost/cut ±15 dB. Also
adjustable high and low shelving fi lters.
Filters: Highpass and lowpass per channel. Butterworth 12/18 dB per octave
and Linkwitz-Riley 24 dB per octave. High and low shelving fi lters, one per
channel.
Delay: Up to 50 msec total delay per channel.
Output Limiter: Prevents clipping and protects loudspeakers. Choice of ?3, ?6,
or ?12 dB threshold per channel.
Presets: 5 user-defi nable loudspeaker presets and 15 factory-default JBL
system presets.
Protection shall include the following:
DSi-Series amplifi ers shall be protected against shorted, open or mismatched
loads; overloaded power supplies; excessive temperature; chain destruction
phenomena; excessive output current, and input overload damage. They also
protect loudspeakers from input/output DC, large or dangerous DC offsets and
turn-on/turn-off transients
The chassis shall be steel. Cooling shall be by a proportional speed fan with
front-to-rear airfl ow.
Dimensions shall be EIA Standard 19-in. rack mount width (EIA RS-310-B), 3.5
in. (8.9 cm) high and 12.25 in. (31.11 cm) deep behind mounting surface.
Net weight shall be 19 lb (8.6 kg). Shipping weight shall be 22 lb (10.0 kg) |
BASIC Series - Intelligent Power
BASIC - that's meeting the tightest budgets and professional requirements
in reliability, flexibility and sound. Alone or in combination with the other
products of the Bittner portfolio.
The consequent realisation of the Bittner quality standards indicates once
more our understanding of the contracting business. It underlines our philosophy
that cost consciousness has nothing to do with giving up standards. Compromise
is a word unknown to Bittner Audio!
The incorporation of detent potentiometers, clip limiter, protection circuits for
any imaginable situation, as well as a first-class production process using only
highest-quality components made the BASIC series the choice of most contractors.
Certainly more than basic!
High Tech SMT design
Excellent sound and superior impulse response
Protection Circuits: DC, LF, HF, Thermal, Short Circuit, Current Limiter, 3 ms Muting Delay
XLR Inputs
Speakon and Binding Posts
Clip Limiter
Toroidal transformers
LED Indicators for SIGNAL, CLIP, PROTECT, POWER
Temperature controlled, variable speed, low noise fans
Detent potentiometers
Stereo / Bridged / Parallel Mode
Ground Lift
Robust Steel Chassis
3 Year Warranty
TECHNICAL DATA:
Basic 400: 2x 200 W @ 4 Ohm
Class: AB
Frequency Response: 20 Hz - 20 kHz (0 / -0.3 dB)
THD: < 0.03%
Signal-to-Noise Ratio: < -102 dB
Channel Seperation: > 85 dB
Input Sensitivity: +6 dBu
Input Clipping: 22 dBu
Input Impedance: 20 kOhm
Damping Factor: > 400 @ 4 Ohm
Cooling: 2x Fan (temp. reg. variable speed)
Weight: 12 kg.
Dimensions : 2 RU/483x89x265 mm (19" x 3.5" x 12.6“) | L2400 750W-750W 4ohm (500W-500W 8ohm)
COMPACT MODERN DESIGN
Compact size (2U-Rack Height) with up to 1200W per channel@2ohms
these amps save valuable rack space without compromising power output.
HIGH CURRENT TOROIDAL TRANSFORMER
A high-current toroidal transformer saves rack space
and minimizes hum and noise.
EXCELLENT SOUND QUALITY
The low T.H.D.(0.05%) and high damping factor (400 or higher)
gives excellent sound quality.
2 STAGE POWER SUPPLY
The high-power units (L1800 and L2400) have a 2-Stage Class-H design
that maximizes their performance.
EQUIPPED WITH 30Hz or 50Hz HPF
All amplifiers are equipped with high-pass filters on each channel to
help maintain sound quality, yet help protect the loudspeakers.
EXTENSIVE PROTECTION CIRCUITS
Extensive protection circuits monitor over voltage/current conditions, overheating,
output shorts, and DC voltage to improve performance and reliability.
CLIP-LIMITER CIRCUITS
Clip-limiters on each channel are provided to help prevent
distortion due to excessive signal levels.
L.E.D FUNCTION DISPLAYS
Power, Clip limiter, Signal, Protection, Mode (Parallel/Stereo/Bridged)
LEDs on the front panel indicate the status of the unit in operation. |
Power Output Level R-150 PLUS
STEREO
8ohm(T.H.D 0.05%) 50W+50W
4ohm(T.H.D 0.05%) 75W+75W
BRIDGED MONO
8ohm(T.H.D 0.05%) 50W
8ohm(T.H.D 0.5%) 170W
Frequency Response 20Hz- 20kHz, ±0.5dB
Convection Cooled
SoftStart Protection System
Balanced 10kΩ@0.775V Inputs
|
Reviews
There are no reviews yet.